01.080.20 特定设备用图形符号 标准查询与下载
共找到 356 条与 特定设备用图形符号 相关的标准，共 24 页
1.1 This practice establishes a set of symbols to be used for marking of packages or containers to indicate special handling and storage requirements. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Pictorial Markings for Handling of Goods
- ICS
- 01.080.20
- CCS
- 发布
- 2021-10-01
- 实施
Medical devices - Symbols to be used with information to be supplied by the manufacturer - Part 1: General requirements (ISO 15223-1:2021)
- ICS
- 01.080.20
- CCS
- 发布
- 2021-10-00
- 实施
- 2021-10-01
This document specifies symbols used to express information supplied for a medical device. This document is applicable to symbols used in a broad spectrum of medical devices, that are available globally and need to meet different regulatory requirements. These symbols can be used on the medical device itself, on its packaging or in the accompanying information. The requirements of this document are not intended to apply to symbols specified in other standards.
Medical devices - Symbols to be used with information to be supplied by the manufacturer - Part 1: General requirements (ISO 15223-1:2021)
- ICS
- 01.080.20
- CCS
- 发布
- 2021-09-29
- 实施
- 2021-12-31
Road vehicles. Symbols for controls, indicators and tell-tales
- ICS
- 01.080.20
- CCS
- 发布
- 2021-09-20
- 实施
- 2021-09-20
Basic and safety principles for man-machine interface, marking and identification – Identification of equipment terminals, conductor terminations and conductors
- ICS
- 01.080.20
- CCS
- 发布
- 2021-09-07
- 实施
- 2021-09-07
IEC 60445:2021 is available as IEC 60445:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60445:2021 applies to the identification and marking of terminals of electrical equipment such as resistors, fuses, relays, contactors, transformers, rotating machines and, wherever applicable, to combinations of such equipment (e.g. assemblies), and also applies to the identification of terminations of certain designated conductors. It also provides general rules for the use of certain colours or alphanumeric notations to identify conductors with the aim of avoiding ambiguity and ensuring safe operation. These conductor colours or alphanumeric notations are intended to be applied in cables or cores, busbars, electrical equipment and installations. This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It has the status of a basic safety publication in accordance with IEC Guide 104. IEC 60445:2021 cancels and replaces the sixth edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) the definitions have been aligned with IEC 60050-195:2021 and IEC 60050-826; b) the provisions for colour to be used for identification of certain designated conductors are made requirements and not only recommendations; c) introduction of a new subclause on marking of protective terminals for multiple power supply inputs on equipment.
Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor terminations and conductors
- ICS
- 01.080.20
- CCS
- 发布
- 2021-09-03
- 实施
- 2021-11-20 (7)
This document specifies symbols (i.e. conventional signs) for use on controls, indicators and tell-tales applying to passenger cars, light and heavy commercial vehicles and buses, to ensure identification and facilitate use. This document additionally describes the purpose and application for the symbols. It also indicates the colours of possible optical tell-tales, which inform the driver of either correct operation or malfunctioning of the related devices.
Road vehicles - Symbols for controls, indicators and tell-tales
- ICS
- 01.080.20
- CCS
- T39
- 发布
- 2021-09-00
- 实施
This document specifies symbols used to express information supplied for a medical device. This document is applicable to symbols used in a broad spectrum of medical devices, that are available globally and need to meet different regulatory requirements. These symbols can be used on the medical device itself, on its packaging or in the accompanying information. The requirements of this document are not intended to apply to symbols specified in other standards.
Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Part 1: General requirements
- ICS
- 01.080.20
- CCS
- 发布
- 2021-07-06
- 实施
- 0000-00-00
This Regulation applies to vehicles of categories L1 and L3 1 with regard to driver operated controls. This Regulation specifies requirements for the location, identification, illumination and operation of controls, tell-tales and indicators on mopeds and motorcycles.
Uniform provisions concerning the approval of two-wheeled motor cycles and mopeds with regard to driver-operated controls including the identification of controls, tell-tales and indicators
- ICS
- 01.080.20
- CCS
- 发布
- 2021-07-01
- 实施
ISO 3767-4:2016 standardizes symbols for use on operator controls and other displays on forestry machinery.
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 4: Symbols for forestry machinery
- ICS
- 01.080.20
- CCS
- 发布
- 2021-07-01
- 实施
ISO 3767-5:2016 standardizes symbols for use specifically on operator controls and other displays on manual portable forestry machines such as chain saws and brush saws.
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 5: Symbols for manual portable forestry machines
- ICS
- 01.080.20
- CCS
- 发布
- 2021-07-01
- 实施
ISO 3767-3:2016 standardizes symbols for use on operator controls and other displays on powered lawn and garden equipment.
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment — Symbols for operator controls and other displays — Part 3: Symbols for powered lawn and garden equipment
- ICS
- 01.080.20
- CCS
- 发布
- 2021-07-01
- 实施
Earth-moving machinery -- Machine safety labels -- General principles
- ICS
- 01.080.20
- CCS
- P97
- 发布
- 2021-04-20
- 实施
本文件规定了智能坐便器的常用图形符号。 本文件适用于智能坐便器, 用于智能坐便器的操作控制器、 指示器和相关文件, 表明智能坐便器的特征、 操作指示、 功能状况等。
Graphical symbols for smart toilets
- ICS
- 01.080.20
- CCS
- C307
- 发布
- 2021-03-30
- 实施
- 2021-09-25
Road vehicles – Motorcycles and mopeds – Symbols for controls, indicators and tell-tales
- ICS
- 01.080.20
- CCS
- 发布
- 2021-03-19
- 实施
- 2021-03-19
Road vehicles. Motorcycles and mopeds. Symbols for controls, indicators and tell-tales
- ICS
- 01.080.20
- CCS
- 发布
- 2021-03-11
- 实施
- 2021-03-11
Le présent amendement spécifie de nouveaux symboles liés à de nouvelles fonctions, principalement assurées par les systèmes de commande électroniques concernant le virage en fourrière du tracteur, le bras de relevage arrière, le contrôle de traction de l'attelage arrière, l'attel
Tractors, machinery for agriculture and forestry, powered lawn and garden equipment - Symbols for operator controls and other displays - Part 2 : Symbols for agricultural tractors and machinery - Amendment 1
- ICS
- 01.080.20
- CCS
- 发布
- 2021-03-03
- 实施
- 2021-03-03
This document specifies the symbols, i.e. conventional signs, used to identify certain controls, indicators and tell-tales on a motorcycle/moped1) and to facilitate their usage. This document also indicates the colours of possible optical tell-tales which warn the rider of the operation or malfunctioning of the related devices and equipment. This document is applicable to those controls, indicators and tell-tales, which, when used, are fitted on the instrument panel or in the immediate vicinity of the motorcycle/moped rider.
Road vehicles - Motorcycles and mopeds - Symbols for controls, indicators and tell-tales
- ICS
- 01.080.20
- CCS
- T80
- 发布
- 2021-03-00
- 实施
Graphical symbols for thermal cutting equipmen
- ICS
- 01.080.20
- CCS
- 发布
- 2021-01-26
- 实施
Graphical symbols for thermal cutting equipmen
- ICS
- 01.080.20
- CCS
- 发布
- 2021-01-26
- 实施
