97.220.30 标准查询与下载

T/ZZB 1123-2019 室内健身小蹦床

本标准规定了室内健身小蹦床的术语和定义、产品分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存、质量承诺。 本标准适用于直径规格80cm～150cm，离地高度22cm～38cm，承重100 kg及以下，供14周岁～60周岁人群室内健身用的小蹦床（以下简称“小蹦床”）。 本标准不适用于安装有扶手、护栏等辅助装置的小蹦床。

Indoor mini body-building trampoline

EN ISO 20957-9:2016/A1:2019 固定的训练器材-第9部分:椭圆形教练器附加的特殊安全要求和试验方法 包含修改件A1,2019

Stationary training equipment - Part 9: Elliptical trainers, additional specific safety requirements and test methods - Amendment 1 (ISO 20957-9:2016/Amd 1:2019)

ISO 20957-9:2016/Amd 1:2019 固定训练设备第9部分:椭圆训练器附加特殊安全要求和试验方法修改1

Stationary training equipment — Part 9: Elliptical trainers, additional specific safety requirements and test methods — Amendment 1

ASTM F406-19 非全尺寸婴儿床/游乐场的标准消费者安全规范

1.1 This consumer safety specification establishes testing requirements for structural integrity and performance requirements for non-full-size cribs/play yards, both rigid sided and mesh/fabric assemblies. It also provides requirements for labeling and instructional material. The term unit or product will refer to a non-full-size crib/play yard. 1.2 This specification covers a framed enclosure with a floor made for the purpose of providing sleeping and playing accommodations for a child who cannot climb out and is less than 35 in. (890 mm) in height. It also covers bassinet, changing table, or similar accessories to a non-full size crib/play yard. These accessories shall also comply with the applicable requirements of ASTM standards addressing those accessories. For example, a changing table that attaches to a play yard shall also comply with the applicable requirements in Specification F2388. This specification does not cover inflatable products. 1.3 No product produced after the approval date of this consumer safety specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all applicable requirements contained herein, before and after all testing. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This consumer safety specification includes the following sections: Title Section Scope 1 Referenced Documents 2 ASTM Standards 2.1 EN Standards 2.2 ISO Standards 2.3 Federal Regulations 2.4 Terminology 3 Definitions of Terms Specific to This Standard 3.1 Accessory 3.1.1 Accessory Attachment Components 3.1.2 Bassinet/Cradle Accessory 3.1.3 Cantilevered Accessory 3.1.4 1 This consumer safety specification is under the jurisdiction of ASTM Committee F15 on Consumer Products and is the direct responsibility of Subcommittee F15.18 on Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Changing Tables. Current edition approved March 15, 2019. Published May 2019. Originally approved in 1977. Last previous edition approved in 2017 as F406 – 17. DOI: 10.1520/F0406-19. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 Conspicuous 3.1.5 Cord 3.1.6 Corner Post 3.1.7 Dropgate 3.1.8 Dynamic Load 3.1.9 Fabric 3.1.10 Foldable Side or End 3.1.11 Key Structural Elements 3.1.12 Manufacturer’s Recommended Use Position 3.1.13 Mattress 3.1.14 Mattress Support Surface 3.1.15 Mesh 3.1.16 Mesh/Fabric Unit 3.1.17 Moveable Side 3.1.18 Non-Full-Size Crib 3.1.19 Non-paper Label 3.1.20 Occupant 3.1.21 Paper Label 3.1.22 Play Yard 3.1.23 Protrusion 3.1.24 Rigid Sided Product 3.1.25 Seam 3.1.26 Static Load 3.1.27 Stationary Side 3.1.28 Strap 3.1.29 Structural Failure 3.1.30 Calibration and Standardization 4 General Requirements 5 Corner Posts 5.1 Scissoring, Shearing, or Pinching 5.6 Latching and Locking Mechanisms 5.8 Openings 5.9 Protective Components 5.10 Labeling 5.11 Stability 5.12 Cord/Strap Length 5.13 Coil Springs 5.14 Entrapment in Accessories 5.15 Mattress 5.16 Mattresses for Rigid Sided Products 5.17 Protrusions 5.18 Bassinet/Cradle Accessories – Missing Accessory Attachment Components 5.19 Record Keeping 5.20 Performance Requirements for Rigid Sided Products 6 Crib-Side Height 6.2 Spacing of Unit Components 6.3 Hardware 6.4 Fasteners 6.5 Construction and Finishing 6.6 Requirements for Cutouts 6.7 Plastic Teething Rail 6.10 Cyclic Test 6.11 Side(s) or End(s) Latch Testing, or Both 6.12 Dropgate or Other Moveable Side Latch Testing 6.12.1 Foldable Side or End Latch Testing 6.12.2 Mattress Support System Vertical Impact Test Requirements 6.13 Mattress Support System Testing 6.14 Crib Side Test Requirements 6.15 Spindle/Slat Strength Testing 6.16 Performance Requirements for Mesh/Fabric Products 7 Height of Sides 7.2 Side Deflection and Strength 7.3 Floor Strength 7.4 Top Rail Covering Material 7.5 Mesh Requirements 7.6 Mesh Openings 7.6.1 Mesh Strength 7.6.2 Fabric Material Requirements 7.7 Fabric Strength 7.7.1 Mesh/Fabric Assembly Requirements 7.8 Sewn Assembly 7.8.1 Seam Strength 7.8.2 Mesh/Fabric Attachment Strength 7.8.3 Mattress Vertical Displacement 7.9 Top Rail Configuration 7.10 Top Rail to Corner Post Attachment 7.11 Test Methods 8 Component Spacing Test Apparatus 8.1 Component-Spacing Test Method 8.2 Test Requirements for Cutouts 8.3 Plastic Teething Rail Test for Rigid Sided Products 8.4 Cyclic Test 8.5 Side or End Latch Test, or Both, for Rigid Sided Products 8.6 Movable Side Latch Tests 8.6.3 Hinged Drop Gate Latch Test 8.6.4 Test Procedure for Latches to Prevent Folding of a Foldable Side or End 8.6.5 Mattress Support System Vertical Impact Test for Rigid Sided Products 8.7 Mattress Support System Test for Rigid Sided Products 8.8 Crib Side Test 8.9 Crib Side Cyclic Tests 8.9.4 Crib Side Static Test 8.9.5 Crib Side Spindle/Slat Torque Test 8.9.6 Spindle/Slat Static Load Strength 8.10 Side Deflection and Strength Tests for Mesh/Fabric Products 8.11 Floor Strength Test for Mesh/Fabric Products 8.12 Locking Mechanism Test 8.13 Dropgate Locking Device Test Method 8.13.1 Folding Latch Test Method 8.13.2 Mesh Opening Test 8.14 Test for Strength of Mesh and Integrity of Attachment 8.15 Mesh/Fabric Attachment Strength Test Method 8.16 Test for Stability of Product 8.17 Permanency of Labels and Warnings 8.18 Removal of Protective Components 8.21 Torque Test 8.21.3 Tension Test 8.21.4 Vinyl Thickness Measurement 8.22 Test for Attachment of Storage Pouch or Other Parts with Printed Warnings 8.23 Cord/Strap Length Test Method 8.24 Protrusions 8.25 Entrapment Tests 8.26 False Latch 8.27 Mattress Vertical Displacement Test 8.28 Top Rail Configuration Test 8.29 Minimum Space when Folded 8.29.1 Top Rail V-Shape Configuration Test 8.29.2 Top Rail to Corner Post Attachment Test 8.30 Load Application Procedure 8.30.3 Bassinet and Cradle Accessory – Sleep Surface Collapse/Tilt 8.31 Marking and Labeling 9 Labeling 9.1 Warning Statements 9.2 Instructional Literature 10 Warning Statements 10.1.2 Water Mattress Use 10.3.3 Keywords 11 Design Guidelines for Protrusions Annex A2 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the F406 − 19 2 Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards

ASTM F2983-13(2018) 摔跤垫标签和保养说明制造商标准指南

1.1 This guide sets forth labeling and instruction guidelines for manufacturers of wrestling mats. 1.2 This guide applies only to wrestling mats whose standard specifications are under auspices of ASTM Committee F08. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Manufacturers for Labeling and Care Instructions for Wrestling Mats

ASTM F2106-18 评价电动跑步机设计和性能特性的标准试验方法

1.1 These test methods specify procedures and equipment used for testing and evaluating a motorized treadmill for compliance to Specification F2115. Both design and operational parameters will be evaluated. Where possible and applicable, accepted test methods from other recognized bodies will be used and referenced. In case of a conflict between this document and Specification F2115, Specification F2115 takes precedence. 1.2 This test method is to be used in conjunction with Specification F2276, Test Methods F2571, and Specification F2115. 1.3 This standard takes precedence over Specification F2276 and Test Methods F2571 in areas that are specific to motorized treadmills. 1.4 Requirements—A motorized treadmill is to be tested for all of the following parameters: 1.4.1 Stability, 1.4.2 Exterior design, 1.4.3 Endurance loading, 1.4.4 Static loading, 1.4.5 Adjustable incline system, 1.4.6 Controls, 1.4.7 Motorized drive system, 1.4.8 Folding treadmills, 1.4.9 Additional universal design requirements, 1.4.10 Documentation, 1.4.11 Marking, and 1.4.12 Warnings/Warning labels. 1.5 This test method2 contains additional requirements to address the accessibility of the equipment for persons with disabilities. 1.6 The values stated in SI units are to be regarded as the standard. The values in parenthesis are for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 These test methods are under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and are the direct responsibility of Subcommittee F08.30 on Fitness Products. Current edition approved June 1, 2018. Published July 2018. Originally approved in 2001. Last previous edition approved in 2012 as F2106 – 12. DOI: 10.1520/ F2106-18. 2 This work was funded, in part, by the Rehabilitation Engineering Research Center on RecTech through the National Institute on Disability, Independent Living, and Rehabilitation Research grant #90RE5009-01-00. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 2. Referenced Documents

Standard Test Methods for Evaluating Design and Performance Characteristics of Motorized Treadmills

ASTM F1250-18 固定式直立和横卧运动自行车及上半身和全身测功器的标准规范

Standard Specification for Stationary Upright and Recumbent Exercise Bicycles and Upper and Total Body Ergometers

ASTM F2115-18 电动跑步机的标准规格

Standard Specification for Motorized Treadmills

ASTM F3023-18 评定固定式直立和横卧运动自行车及上半身和全身测功器的设计和性能特性的标准试验方法

1.1 These test methods specify procedures and equipment used for testing and evaluating stationary exercise upright and recumbent bicycles and ergometers for compliance to Specification F1250. Both design and operational parameters will be evaluated. Where possible and applicable, accepted test methods from other recognized bodies will be used and referenced. In the case of a conflict between this document and Specification F1250, Specification F1250 takes precedence. 1.2 Requirements—Stationary exercise bicycles and ergometers are to be tested for the parameters specified in Specification F2276 and Test Methods F2571 and the following parameters unique to this equipment: 1.2.1 Seat post construction and loading, 1.2.2 Handlebar construction and loading, 1.2.3 Pedal construction and loading, 1.2.4 Crank arm and enclosure entrapment, 1.2.5 Seat back support loading, 1.2.6 Stability, 1.2.7 Direct Drive Exercise Bicycle Pedal Endurance, 1.2.8 Warnings, and 1.2.9 Documentation. 1.3 This test method2 contains additional requirements to address the accessibility of the equipment for persons with disabilities. 1.4 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Evaluating Design and Performance Characteristics of Stationary Upright and Recumbent Exercise Bicycles and Upper and Total Body Ergometers

BS EN ISO 20957-8:2017 固定式训练设备.第8部分:步进机、阶梯攀缘器和攀缘器.附加的特殊安全要求和试验方法

Stationary training equipment. Steppers, stairclimbers and climbers. Additional specific safety requirements and test methods

BS EN ISO 20957-10:2017 固定的训练器材.第10部分:带固定轮或无自由飞轮的训练自行车.附加特定安全要求和试验方法

Stationary training equipment. Exercise bicycles with a fixed wheel or without freewheel. Additional specific safety requirements and test methods

KS G ISO 20957-6:2017 固定训练设备第6部分:跑步机附加特殊安全要求和试验方法

Stationary training equipments－Part 6：Treadmills, additional specific safety requirements and test methods

KS G ISO 20957-6-2017(2022) 固定式训练设备第6部分:跑步机、附加特殊安全要求和试验方法

Stationary training equipments－Part 6：Treadmills, additional specific safety requirements and test methods

KS G ISO 20957-6-2017 固定训练设备第6部分:跑步机附加特殊安全要求和试验方法

Stationary training equipments－Part 6：Treadmills, additional specific safety requirements and test methods

KS G ISO 20957-2-2017(2022) 固定训练设备.第2部分:力量训练设备.附加特殊安全要求和试验方法

Stationary training equipment — Part 2: Strength training equipment — Additional specific safety requirements and test methods

KS G ISO 20957-2:2017 固定式训练器材 第2部分：力量训练器材附加的特殊安全要求和试验方法

Stationary training equipment — Part 2: Strength training equipment — Additional specific safety requirements and test methods

KS G ISO 20957-2-2017 固定训练设备 - 第2部分:力量训练设备 附加的具体安全要求和测试方法

Stationary training equipment — Part 2: Strength training equipment — Additional specific safety requirements and test methods

T/CSSGA 1003.5-2017 搏击类运动护具 第5部分：护裆

T/CSSGA 1003的本部分规定了护裆的分类、要求、试验方法、检验规则和标识、包装、运输、贮存。

Protective equipment for martial arts—Part 5：Genital protectors

T/CSSGA 1003.7-2017 搏击类运动护具 第7部分：拳套

T/CSSGA 1003的本部分规定了拳套的分类、要求、试验方法、检验规则和标识、包装、运输、贮存。

Protective equipment for martial arts—Part 7：Hand protectors

T/CSSGA 1003.8-2017 搏击类运动护具 第8部分：护脚

T/CSSGA 1003的本部分规定了护脚的要求、试验方法、检验规则和标识、包装、运输、贮存。

Protective equipment for martial arts—Part 8：Instep and foot protectors