01.100.20 机械工程制图 标准查询与下载

BS ISO 15786:2008 技术图纸 孔的简化表示和尺寸标注

BS ISO 15786:2008 Technical drawing. Simplified representation and dimensioning of holes BS ISO 15786 has been established to specify the simplified representation and dimensioning of holes. It establishes rules to determine, unambiguously, methods for the representation — both complete and simplified — and the dimensioning of holes, as well as the structure and sequence of the descriptive elements for the simplified representation of holes. Contents of BS ISO 15786: Foreword Introduction Scope Normative references Terms and definitions Methods of representation and dimensioning of holes Complete representation and complete dimensioning of holes Complete representation and simplified dimensioning of holes Simplified representation and simplified dimensioning of holes Representation of holes on the same drawing Structure of dimensioning of holes Structure and sequence of descriptive elements for simplified dimensioning of holes Graphical symbols Number of groups of holes and number of holes in a group Indication of tolerances Hole bottom Countersinks and chamfers Depth dimensions Indication of surface texture Indication of dimensions on geometrical tolerances Examples for representation and dimensioning of holes, counterbores and internal threads Bibliography

Technical drawings. Simplified representation and dimensioning of holes

BS ISO 15786:2009 技术制图.孔洞的简化表示法和尺寸规格

Technical drawings - Simplified representation and dimensioning of holes

LST EN ISO 10135:2009 产品几何规格（GPS） 技术产品文档（TPD）中模塑零件的绘图指示（ISO 10135:2007）

Geometrical product specifications (GPS) - Drawing indications for moulded parts in technical product documentation (TPD) (ISO 10135:2007)

NF E04-131*NF EN ISO 10135:2009 产品几何量技术规范(GPS).技术产品文件(TPD)中模压零件的图纸说明

Geometrical product specifications (GPS) - Drawing indications for moulded parts in technical product documentation (TPD).

ISO 15786:2008 工程制图.孔的简化表示和尺寸标记

Technical drawings - Simplified representation and dimensioning of holes

GSO ISO 10110-17:2008 光学和光子学 光学元件和系统图纸的准备 第17部分：激光辐照损伤阈值

ISO 10110 specifies the presentation of design and functional requirements for optical elements in technical drawings used for manufacturing and inspection. This part of ISO 10110 specifies rules for the indication of the damage threshold from laser irradiation up to which optical surfaces shall not exhibit any damage as defined in ISO 11254-1.

Optics and photonics - Preparation of drawings for optical elements and systems - Part 17: Laser irradiation damage threshold

DIN 30630:2008 工程制图.机械工程中的一般公差.公差规则和总体规划

Technical drawings - General tolerances in mechanical engineering - Tolerance rule and general plan

KS B ISO 10135-2007 技术图纸 模制、铸造和锻造零件的简化表示

Technical drawings－Simplified representation of moulded, cast and forged parts

KS B ISO 1101-2007 技术图纸 几何公差 形状、方向、位置和跳动的公差 一般性、定义、符号、图纸上的指示

Technical drawings－Geometrical tolerancing－Tolerancing of form, orientation, location and run-out－Generalities, definitions, symbols, indications on drawings

KS B ISO 2692-2-2007 技术图纸 形位公差 最大材料原则 第2部分：最小材料要求

Technical drawings－Geometrical tolerancing－Maximum material principle－Part 2：Least material requirement

KS B ISO 2692-1-2007 技术图纸 形位公差 最大材料原理

Technical drawings－Geometrical tolerancing－Maximum material principle

KS B ISO 2692-1:2007 技术制图几何公差最大材料原则

Technical drawings－Geometrical tolerancing－Maximum material principle

KS B ISO 2692-2:2007 技术制图几何公差最大材料原则 第2部分：最小材料要求

Technical drawings－Geometrical tolerancing－Maximum material principle－Part 2：Least material requirement

KS B ISO 1101:2007 技术制图几何公差形状、方向、位置和跳动公差总则、定义、符号、图纸标注

Technical drawings－Geometrical tolerancing－Tolerancing of form, orientation, location and run-out－Generalities, definitions, symbols, indications on drawings

KS B ISO 10135:2007 技术制图模制、铸造和锻造零件的简化表示法

Technical drawings-Simplified representation of moulded, cast and forged parts

DS-håndbog 112.3:2007 技术产品文件 机械机械工程图 第3部分：特定图纸指示

This DS-handbook 112.3 contains specific standards for mechanical engineering drawings. It deals with general drawing indications and indication of machinery components.

Technical product documentation - Mechanical mechanical engineering drawings - Part 3: Specific drawings indications

DS-håndbog 112.2:2007 技术产品文档 机械机械工程制图 第2部分：表示的一般原则

This DS-handbook 112.2 contains general standards for mechanical engineering drawings.It deals with general drawing rules.

Technical product documentation - Mechanical mechanical engineering drawing - Part 2: General principles of presentation

DS/EN ISO 2692:2007 产品几何规格（GPS） 几何公差 最大材料要求（MMR）、最小材料要求（LMR）和互易要求（RPR）

This International Standard defines the maximum material requirement, the least material requirement, the reciprocity requirement and specifies their applications. The use of these requirements is to control specific functions of workpieces where there is a mutual dependence of size and geometry, for fulfilling the function assembly of parts (for maximum material requirement) and e.g. for fulfilling the function minimum wall thickness (for least material requirement). However the maximum material requirement and least material requirement may be used to fulfill other functional design requirements.

Geometrical product specifications (GPS) - Geometrical tolerancing - Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)

JIS B 0004:2007 弹簧的技术表示法

この規格は，ばねの図示方法及び設計·製作仕様の表示方法について規定する。

Technical representation of springs

KS B ISO 5460-2005(2010) 技术图纸 - 几何公差 - 形式 方向 位置和运行的公差 - 验证原则和方法 - 指南

Technical drawings - Geometrical tolerancing - Tolerancing of form, orientation, location and run-out - Verification principles and methods - Guidelines