01.100.20 机械工程制图 标准查询与下载

BS EN ISO 15785:2002 技术制图.粘合叠层和压连接接点的符号表示和标示

Technical drawings - Symbolic presentation and indication of adhesive fold and pressed joints

DS/ISO 128-44:2002 技术制图 表示的一般原则 第44部分：机械工程制图部分

This part of ISO 128 specifies the general principle for presenting sections on mechanical engineering drawings following the orthographic projection methods specified in ISO 5456-2. For areas on sections, representation is according to ISO 128-50.

Technical drawings - General principles of presentation - Part 44: Sections on mechanical engineering drawings

EN ISO 15785:2002 技术制图.符号编写和加压粘合叠层连接件ISO 15785-2002

Technical drawings - Symbolic presentation and indication of adhesive, fold and pressed joints ISO 15785: 2002

ISO 15785:2002 技术制图.粘合、折叠和叠压接缝的符号指示和表示法

This International Standard establishes rules for the symbolic presentation and indication of adhesive, fold and pressed joints in technical drawings.

Technical drawings - Symbolic presentration and indication of adhesive, fold and pressed joints

DS/ISO 13715:2002 技术制图 未定义形状的边缘 词汇和指示

This International Standard defines terms defining the states of edges and specifies rules for representing states of edges of undefined shape in technical drawings.

Technical drawings - Edges of undefined shape - Vocabulary and indications

DS/ISO 128-24:2002 技术制图 表示的一般原则 第24部分：机械工程制图上的线条

This part of ISO 128 specifies general rules and basic conventions for the types of lines on mechanical engineering drawings.

Technical drawings - General principles of presentation - Part 24: Lines on mechanical engineering drawings

KS A ISO 10578-2001(2011) 技术制图方向和位置公差投影公差带

Technical drawings－Tolerancing of orientation and location－Projected tolerance zone

PP 8888-1-2001 工程绘图规程.第1部分:学校和学院使用BS 8888:2000：技术产品文献的指南

Engineering drawing practice - Part 1: A guide for schools and colleges to BS 8888:2001: Technical product documentation

BS ISO 128-34:2001 技术制图.表示的一般原则.机械工程图的视图

This part of ISO 128 specifies rules for the presentation of views additional to those of ISO 128-30 and applicable to mechanical engineering drawings that follow the orthographic projection methods specified in ISO 5456-2. Attention has also been given to reproduction requirements, including those of microcopying according to ISO 6428.

Technical drawings - General principles of presentation - Views on mechanical engineering drawings

BS ISO 128-44:2001 技术制图.表示的一般原则.机械工程制图部分

This part of ISO 128 specifies general principles for presenting sections on mechanical engineering drawings following the orthographic projection methods specified in ISO 5456-2. For areas on sections, representation is according to ISO 128-50[1]. Attention has also been given to the requirements of reproduction, including microcopying in accordance with ISO 6428. NOTE The basic rules for cuts and sections are given in ISO 128-40[2].

Technical drawings - General principles of presentation - Sections on mechanical engineering drawings

NF E04-526-2:2001 技术图纸.表示方法的一般原则.第44部分:机械工程图纸上的截面部位

Technical drawings - General principles of presentation - Part 44 : sections on mechanical engineering drawings.

LST EN ISO 6411:2001 技术图纸 中心孔的简化表示（ISO 6411:1982）

Technical drawings - Simplified representation of centre holes (ISO 6411:1982)

ISO 128-44:2001 技术制图 画法的一般原则 第44部分：机械工程制图的截面图

This part of ISO 128 specifies general principles for presenting sections on mechanical engineering drawings following the orthographic projection methods specified in ISO 5456-2. For areas on sections, representation is according to ISO 128-5011]. Attention has also been given to the requirements of reproduction, including microcopying in accordance with ISO 6428. NOTE The basic rules for cuts and sections are given in ISO 128-40'2l

Technical drawings - General principles of presentation - Part 44: Sections on mechanical engineering drawings

ISO 128-34:2001 技术制图 画法的一般原则 第34部分:机械工程制图的视图

This part of ISO 128 specifies rules for the presentation of views additional to those of ISO 128-30 and applicable to mechanical engineering drawings that follow the orthographic projection methods specified in ISO 5456-2. Attention has also been given to reproduction requirements, including those of microcopying according to ISO 6428.

Technical drawings - General principles of presentation - Part 34: Views on mechanical engineering drawings

KS B 0618-2000(2005) 中心孔表示法

Representation of center hole

DIN 6780:2000 技术制图.孔的简化画法和尺寸标注

The document contains rules for the symbolic representation of holes, counterbores, countersinks and chamfers as well as internal threads and the simplified dimensioning of which by means of leader lines. Apart form the indication of the dimensions of cross sections and depth requirements concerning the features the indication of tolerances of dimensions, form and positions, the indication of surface roughness and the dimensioning of groups of holes are also specified.

Technical drawings - Simplified representation and dimensioning of holes

BS ISO 10579:2000 技术图纸.尺寸和公差.非刚性零部件

Gives rules for dimensioning and tolerancing non-rigid parts where restraining of features is required during verification of dimensions and tolerances specified on a drawing and specifies indications on drawings.

Technical drawings - Dimensioning and tolerancing - Non-rigid parts

JIS B 0001:2000 机械工程技术制图

この規格は，JIS Z 8310に基づき，機械工業の分野で使用する，主として部品図及び組立図の製図について規定する。なお，この規格に規定していない事項については，JIS Z 8310及びそれぞれ別に定める製図に関する日本工業規格による。

Technical drawings for Mechanical Engineering

JIS B 0028:2000 技术制图.尺寸和公差表示.锥形

この規格は，円すいの図面指示に用いる図記号及び寸法.公差の表示方式を規定する。この規格では，軸直角断面()が円である円すいだけを扱う。注()JIS B 0154(円すぃ用語)の204参照 備考1.この規格では，簡単のために円すい台だけで図示してぃるが、適用範囲に従う円すいであれば，どんなタイプの円すいにも適用してよい。2.この規格に規定する寸法.公差の表示方式以外の方式を禁止するものではない。

Technical drawings -- Dimensioning and tolerancing -- Cones

JIS B 0029:2000 技术制图.方向和位置的公差表示.突出公差带

この規格は，突出公差域の定義及びその表示方式について規定する。備考1.この規格に定める方式は，JIS B 0021の13.同とじでぁる。2.この規格の対応国際規格を次に示す。ISO 10578: 1992 Technical drawings-Tolerancing of orientation and location-Projected tolerance zone

Technical drawings -- Tolerancing of orientation and location -- Projected tolerance zone