01.100.20 机械工程制图 标准查询与下载
共找到 332 条与 机械工程制图 相关的标准，共 23 页
この規格は，線である部分の輪郭(profiled outline)及び面である部分の輪郭(profiled surface)の寸法及び幾何公差の表示方式について規定する。備考 この方式は，JIS B 0021の中に“線の輪郭度公差”及び“面の輪郭度公差”として示してある。
Technical drawings -- Dimensioning and tolerancing of profiles
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 2000-03-20
- 实施
The fire prevention code official shall recommend to the chief administrative official of the municipality the location or relocation of new or existing fire hydrants and the placement or replacement of inadequate water mains located upon public prope
International Mechanical Code
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 2000-01-01
- 实施
The provisions requiring that the excavation left when an unfit structure has been removed be filled in is an obvious, but often neglected means of protecting the public health and safety.
International Mechanical Code
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 2000-01-01
- 实施
1.1 本标准适用于几何公差包括形状、方向、定位及偏转度等公差之符号之制定以及在工程图上之标注方法并确立适当之几何定义。1.2 几何公差祇在必要时材标注，亦即根据功能需求，互换性及制造环境，作为标注之依据。1.3 几何公差之标注并不代使用特殊之制造或量测法。
Engineering drawings - Geometrical toleranicing
- ICS
- 01.100.20
- CCS
- 发布
- 1999-12-03
- 实施
- 1999-12-03
Engineering drawings - Geometrical toleranicing
- ICS
- 01.100.20
- CCS
- 发布
- 1999-12-03
- 实施
This International Standard describes positional tolerancing. This tolerancing method is applied to the location of a point, of a line nominally straight and of a surface nominally plane, e.g. the centre of a sphere, the axis of a hole or shaft and the median surface of a slot.
Geometrical product specifications (GPS) - Geometrical tolerancing - Positional tolerancing
- ICS
- 01.100.20
- CCS
- 发布
- 1999-07-01
- 实施
- 1999-05-20
この規格は，センタ穴の簡略図示方法及びその呼び方について規定する。センタ穴の簡略図示方法は，正確な形状及び寸法を特に示す必要がない場合，及び標準化されたセンタ穴の呼び方だけで図面情報として十分に伝えることができる場合に用いる。
Technical drawings -- Simplified representation of centre holes
- ICS
- 01.100.20
- CCS
- J05
- 发布
- 1999-03-20
- 实施
This Standard defines the types of engineering drawings most frequently used to establish engineering requirements. It describes typical applications and minimum content requirements. Drawings for specialized engineering disciplines (e.g., marine, civil, construction, optics, etc.) are not included in this Standard.
Types and Applications of Engineering Drawings Revision of ASME Y14.24M-1989
- ICS
- 01.100.20
- CCS
- P04
- 发布
- 1999-01-01
- 实施
It shall be unlawful to interfere with, attempt to interfere with, conspire to interfere with, obstruct or restnct the mobility of or block the path of travel of any fire department emergency vehicle in any way, or to interfere with, attempt to interf
Mechanical Systems
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 1999-01-01
- 实施
The standard specifies the simplified representation of centre holes and heir designation.
Technical drawings - Simplified representation of centre holes
- ICS
- 01.100.20
- CCS
- 发布
- 1998-04-07
- 实施
- 1998-01-02
This appendix contains various illustrations and diagrams of typical applications of specific code provisions to one- and two-family dwellings and is intended to illustrate the subject matter of the related text.
Mechanical Definitions
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 1998-01-01
- 实施
The provisions requiring that the excavation left when an unfit structure has been removed be filled in is an obvious, but often neglected means of protecting the public health and safety.
General Mechanical System Requirements
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 1998-01-01
- 实施
This eleventh edition presents the code as originally issued, with changes approved through 1989, and with certain editorial changes made to maintain the sequence of the code, to standardize the format of all 1990 BOCA National Codes, and to update the
Mechanical Administration
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 1998-01-01
- 实施
This International Standard specifies the simplified represen-tation of centre holes and their designation. Simplified representation of centre holes may be used particularly when it is not necessary to show the exact form and size and where the designation of standardized centre holes is sufficient for infor-mation.
Technical drawings. Simplified representation of centre holes
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 1997-12-15
- 实施
- 1997-12-15
Technical drawings - Simplified representation of centre holes (ISO 6411:1982)
- ICS
- 01.100.20
- CCS
- J04
- 发布
- 1997-11
- 实施
Technical Drawings - Simplified Representation of Centre Holes ISO 6411: 1982
- ICS
- 01.100.20
- CCS
- 发布
- 1997
- 实施
This International Standard specifies rules complementary to ISO 128 and ISO 129 for the simplified representation of bars and profile sections in assembly and detail drawings concerning, among others: - structural metal work consisting of plates and sheets, profile sections and compound elements (including bridges, frameworks, pilings, etc.); - lifting and transport appliances; - storage tanks and pressure vessels; - lifts, moving stairways and conveyor belts.
Technical drawings - Simplified representation of bars and profile sections
- ICS
- 01.100.20
- CCS
- 发布
- 1996-09-13
- 实施
- 1996-07-03
Gives rules for the simplified representation of compression, extension, torsion, disc, spiral and leaf springs on technical drawings.
Technical product documentation - Springs - Part 1: Simplified representation (ISO 2162-1:1993)
- ICS
- 01.100.20
- CCS
- 发布
- 1996-07-24
- 实施
- 1996-10-31
