11.180.15 标准查询与下载

IEC 60118-7:2005 电声学.助听器.第7部分:助听器生产、供货和交货质量保证的性能特性测量

This standard gives recommendations for the measurement of the performance character-istics of air-conduction hearing aids of a particular model for the purpose of comparing measured properties with those specified by the manufacturer. This standard does not relate to mechanical or environmental tests. It should not be used as the basis for the exchange of information about hearing aid characteristics in general, nor is it intended to be used as a basis for fitting hearing aids to individuals. Note. — Terms such as "manufacturer" and "purchaser" are used in this standard. These terms may be understood, however, to refer to the supplier and recipient respectively in any arrangement for the supply of hearing aids in which the use of this standard is called for.

Electroacoustics - Hearing aids - Part 7: Measurement of performance characteristics of hearing aids for production, supply and delivery quality assurance purposes

GOST R IEC 60118-14-2003 可编程助听器.数字接口设备的规格.接线盒规格

Programmable hearing aids. Specification of a digital interface devices. Dimensions of electrical connectors

ANSI S3.22-2003 助听器特性的规范

Air conduction hearing-aid measurement methods suitable for specification and tolerance purposes. Includes output sound pressure level (SPL) with a 90-dB input SPL, full-on gain, frequency response, harmonic distortion, equivalent input noise, current dr

Specification of Hearing Aid Characteristics

AS ISO 12124:2003 给水用1/2 In.(12 mm)到2 In.(50 mm)聚乙烯-铝-聚乙烯和交联聚乙烯-铝-交联聚乙烯复合压力管

Specifies procedures and requirements for measuring the real-ear acoustical characteristics of hearing aids. Its purpose is to ensure that the same measurements made on a given hearing aid on a given human ear give substantially the same results. This St

Acoustics - Procedures for the measurement of real-ear acoustical characteristics of hearing aids

DIN EN 61669:2002 电声学.助听器真耳听觉特性测量设备 (IEC 61669:2001); 德文版本 EN 61669:2001

The document specifies the general requirements for test equipment designed for use in measuring the real-ear acoustical characteristics of hearing aids and describes the terminology used. The purpose of this International Standard is to ensure that measurements of real-ear acoustical characteristics of a hearing aid on a given human ear, performed with different test equipment which comply with this International Standard using methods described in ISO 12124, shall give substantially the same results.

Electroacoustic - Equipment for the measurement of real-ear acoustical characterics of hearing aids (IEC 61669:2001); German version EN 61669:2001

ISO 11904-1:2002 声学 确定靠近耳朵放置的声源的声音发射 第1部分：在真耳中使用麦克风的技术（MIRE 技术）

This part of ISO 11904 specifies basic framework measurement methods for sound immission from sound sources placed close to the ear. These measurements are carried out with miniature or probe microphones inserted in the ear canals of human subjects. The measured values are subsequently converted into corresponding free-field or diffuse-field levels. The results are given as free-field related or diffuse-field related equivalent continuous A-weighted sound pressure levels. The technique is denoted the microphone-in-real-ear technique (MIRE technique). This part of ISO 11904 is applicable to exposure from sources close to the ear, for example during equipment tests or at the workplace by earphones or hearing protectors with audio communication facilities. This part of ISO 11904 is applicable in the frequency range from 20 Hz to 16 000 Hz.

Acoustics - Determination of sound immission from sound sources placed close for the ear - Part 1: Technique using a microphone in a real ear (MIRE technique)

NF S31-015:2002 电声学.助听器真耳声音特性测量仪

Electroacoustics - Equipment for the measurement of real-ear acoustical characteristics of hearing aids.

DS/ISO 12124:2002 声学 助听器真耳声学特性的测量程序

This standard specifies procedures and requirements for measuring the real-ear acoustical characteristics of hearing aids. Its purpose is to ensure that the same measurements made on a given hearing aid on a given human ear and a given hearing aid, following the procedures described and using equipment complying with the requirements of IEC 61669, give substantially the same results.

Acoustics - Procedures for the measurement of real-ear acoustical characteristics of hearing aids

DS/EN 61669:2002 电声学.助听器真耳声学特性测量设备

This standard specifies the general requirements for test equipment designed for use in measuring the real-ear acoustical characteristics of hearing aids. The purpose is to ensure that measurements of real-ear acoustical characteristics of a hearing aid on a given human ear, performed with different test equipment which comply with this standard using methods described in ISO 12124, shall give substantially the same result.

Electroacoustics - Equipment for the measurement of real-ear acoustical characteristics of hearing aids

BS EN 61669:2001 电声学.助听器真耳声学特性测量设备

This International Standard specifies the general requirements for test equipment designed for use in measuring the real-ear acoustical characteristics of hearing aids and describes the terminology used. The purpose of this International Standard is to ensure that measurements of real-ear acoustical characteristics of a hearing aid on a given human ear, performed with different test equipment which comply with this International Standard using methods described in ISO 12124, shall give substantially the same results.

Electroacoustics. Equipment for the measurement of real-ear acoustical characteristics of hearing aids

BS ISO 12124:2001 声学.助听器真耳声学特性测量规程

This International Standard specifies procedures and requirements for measuring the real-ear acoustical character-istics of hearing aids. Its purpose is to ensure that the same measurements made on a given hearing aid on a given human ear and a given hearing aid, following the procedures described and using equipment complying with the re-quirements of IEC 61669, give substantially the same results. Measurements of real-ear acoustical characteristics of hearing aids which apply non-linear or analytical processing techniques are valid only for the test signals used and conditions employed. These measurements should be per-formed in accordance with the hearing aid manufacturer's recommendations as they may require specific test signals or test conditions outside the scope of this International Standard.

Acoustics - Procedures for the measurement of real-ear acoustical characteristics of hearing aids

ISO 12124:2001 声学.助听器真耳声特性的测量方法

This International Standard specifies procedures and requirements for measuring the real-ear acoustical characteristics of hearing aids. Its purpose is to ensure that the same measurements made on a given hearing aid on a given human ear and a given hearing aid, following the procedures described and using equipment complying with the requirements of IEC 61669, give substantially the same results. Measurements of real-ear acoustical characteristics of hearing aids which apply non-linear or analytical processing techniques are valid only for the test signals used and conditions employed. These measurements should be performed in accordance with the hearing aid manufacturer's recommendations as they may require specific test signals or test conditions outside the scope of this International Standard.

Acoustics - Procedures for the measurement of real-ear acoustical characteristics of hearing aids

DS/EN 60118-6:2001 助听器 第6部分：助听器电输入电路的特性

This part of IEC 60118 specifies the electrical and safety characteristics of a circuit for an external electrical input to a personal hearing aid in order to ensure compatibility with external electrical or electroacoustic signal sources. In this standard, the hearing aid may include an adaptor (audio shoe) which incorporates connector systems described in IEC 60118-12.

Hearing aids - Part 6: Characteristics of electrical input circuits for hearing aids

IEC 61669:2001 电声学 助听器的真耳声学特性的测量设备

This International Standard specifies the general requirements for test equipment designed for use in measuring the real-ear acoustical characteristics of hearing aids and describes the terminology used. The purpose of this International Standard is to ensure that measurements of real-ear acoustical characteristics of a hearing aid on a given human ear, performed with different test equipment which comply with this International Standard using methods described in ISO 12124, shall give substantially the same results.

Electroacoustics - Equipment for the measurement of real-ear acoustical characteristics of hearing aids

GOST R IEC 60711-2001 封闭式耳朵模拟器.技术要求和试验方法

Настоящий стандарт распространяется на имитатор закрытого уха, предназначенный для нагрузки телефонов слуховых аппаратов воздушного зв

Occluded-ear simulator. Technical requirements and test methods

GOST R IEC 60126-2001 测量助听器用参考耦合器.结构要求

Настоящий стандарт распространяется на эталонную камеру малого объема, предназначенную для нагрузки телефонов слуховых аппаратов возду

Reference coupler for the measurement hearing aids. Construction requirements

DIN EN 60118-6:2000 助听器.第6部分:助听器输入线路特性

The document specifies the electrical and safety characteristics of a circuit for an external electrical input to a personal hearing aid in order to ensure compatibility with external electrical or electroacoustic signal sources.

Hearing aids - Part 6: Characteristics of electrical input circuits for hearing aids (IEC 60118-6:1999); German version EN 60118-6:1999

DIN EN 60118-1:1999 助听器.第1部分:带感应耦合线圈输入的助听器（IEC 60118-1-1995+AI-1998)

The document specifies a method of determining the electroacoustic performance of hearing aids fitted with an induction pick-up coil and used in an audio-frequency magnetic field. The induction pick-up performance is measured in a loop simulating conditions of use in room applications.

Hearing aids - Part 1: Hearing aids with induction pick-up coil input (IEC 60118-1:1995 + A1:1998); German version EN 60118-1:1995 + A1:1998

IEC 60118-6:1999 助听器 第6部分:助听器输入电路的特性

This part of IEC 60118 specifies the electrical and safety characteristics of a circuit for an external electrical input to a personal hearing aid in order to ensure compatibility with external electrical or electroacoustic signal sources. In this standard, the hearing aid may include an adaptor (audio shoe) which incorporates connector systems described in IEC 60118-12.

Hearing aids - Part 6: Characteristics of electrical input circuits for hearing aids

DS/EN 60118-1/A1:1999 助听器 第1部分：带感应拾取线圈输入的助听器

This Standard describes a method of determining the electroacoustic performance of hearing aids fitted with an induction pick-up coil and used in an audio-frequency magnetic field. The induction pick-up performance is measured in a loop simulating conditions of use in room applications.

Hearing aids - Part 1: Hearing aids with induction pick-up coil input