13.030.10 固态废物 标准查询与下载
共找到 308 条与 固态废物 相关的标准，共 21 页
Technical specifications for mixed ecological filling of fly ash and coal gangue
- ICS
- 13.030.10
- CCS
- Z06
- 发布
- 2016-08-20
- 实施
- 2016-10-20
Definition of "Low-Halogen" for electronic products
- ICS
- 13.030.10
- CCS
- 发布
- 2016-06-15
- 实施
Technical requirements for carbon footprint assessment of communication products Part 2: Ethernet switches
- ICS
- 13.030.10
- CCS
- Z71
- 发布
- 2016-04-05
- 实施
- 2016-07-01
Technical requirements for carbon footprint assessment of communication products Part 1: Mobile communication handsets
- ICS
- 13.030.10
- CCS
- Z71
- 发布
- 2016-04-05
- 实施
- 2016-07-01
本标准规定了电站锅炉石灰石-石膏湿法烟气脱硫装置性能验收试验的内容、时间、条件和方法。 本标准适用于电站锅炉石灰石-石膏湿法烟气脱硫装置的验收，也可用于为后评估及其他目的的试验，其他烟气脱硫装置的验收也可参照执行。 本标准不适用于脱硫系统中风机、泵、噪声、材料、脱硫废水方面的验收。
Performance test code for wet limestone-gypsum flue gas desulphurization
- ICS
- 13.030.10
- CCS
- Z27
- 发布
- 2016-01-07
- 实施
- 2016-06-01
Characterisation of waste - Leaching behaviour test for basic characterisation - Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s)
- ICS
- 13.030.10
- CCS
- 发布
- 2016-01-06
- 实施
- 2016-01-06
1.1 This specification covers concrete masonry lintels (beams) that are solid in cross-section, are reinforced for flexure, and are made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. These lintels are suitable for both loadbearing and nonloadbearing applications. Note 1: This specification covers only concrete masonry lintels containing reinforcement. Due to building code imposed limitations on the design of masonry lintels, all lintels must contain reinforcement. Concrete masonry lintels are not typically manufactured using shear reinforcement (stirrups or other vertical reinforcement). Therefore, this standard does not address issues related to such. For further guidance, refer to Building Code Requirements for Masonry Structures, TMS8201;402. Prestressed concrete lintels are not covered by this standard. 1.2 Lintels are manufactured using a no-slump concrete mix to provide a surface texture similar to that of concrete masonry. This specification applies to both machine-made and hand-tamped concrete masonry lintels intended for use in concrete masonry applications. 1.3 Concrete masonry lintels covered by this specification are made from lightweight or normal weight aggregates, or both. 1.4 This specification does not address the design or analysis of lintel capacity. Structural evaluations must be performed separately. The strength of a lintel is a function of factors including, but not limited to, the characteristics of the materials used in manufacturing (concrete materials and reinforcement), the amount and location of reinforcement, and the manufacturing and curing procedures. For design and analysis methods, refer to Building Code Requirements for Masonry Structures, TMS8201;402. 1.5 This specification does not cover U-shaped lintels or those of other cross-sections that are not 1008201;% solid. 1.6 This specification does not cover lintels of grouted concrete masonry lintels, or precast or cast-in-place lintels of slump concrete. 1.7 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Standard Specification for Manufactured Concrete Masonry Lintels
- ICS
- 13.030.10
- CCS
- 发布
- 2016
- 实施
Characterization of waste. Leaching behaviour test for basic characterization. Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s)
- ICS
- 13.030.10
- CCS
- Z50
- 发布
- 2015-12-31
- 实施
- 2015-12-31
This Technical Specification is applicable for determining the leaching behaviour of monolithic wastes under dynamic conditions. The test is performed under experimental conditions relevant to assess the leaching behaviour in view of the considered scenario(s). This test is aimed at determining the release as a function of time of inorganic constituents from a monolithic waste, when it is put into contact with an aqueous solution (leachant). In general, the composition, the temperature and the continuous renewal rate of the leachant are chosen such that the leaching behaviour of the waste material can be studied in view of the considered disposal or recovery scenario. When the release needs to be determined without any reference to a specific scenario, the leachant is demineralized water, the temperature and the continuous renewal rate are fixed. This dynamic monolithic leaching test (DMLT) is a parameter specific test as specified in EN 12920 and is therefore not aimed at simulating real situations. The application of this test method alone is not sufficient for the determination of the detailed leaching behaviour of a monolithic waste under specified conditions. In the framework of EN 12920 and in combination with additional chemical information, the test results are used to identify the leaching mechanisms and their relative importance. The intrinsic properties can be used to predict the release of constituents at a given time frame, in order to assess the leaching behaviour of monolithic waste materials, placed in different situations or scenarios (including disposal and recycling scenarios). The test method applies to regularly shaped test portions of monolithic wastes with minimum dimensions of 40 mm in all directions that are assumed to maintain their integrity over a time frame relevant for the considered scenario. The test method applies to test portions for which the geometric surface area can be determined with the help of simple geometric equations. The test method applies to low permeable monolithic materials. NOTE 1 If, in order to comply with the requirements of regular shape, the test portion is prepared by cutting or coring, then new surfaces are exposed which can lead to change(s) in leaching properties. On the other hand if the test portion is prepared by moulding, the surface will be dependent to the type of mould and the conditions of storage. If the intention is to evaluate the behaviour of the material core, the specimen needs to be stored without any contact with air to avoid carbonation. NOTE 2 For monolithic waste materials with a saturated hydraulic conductivity higher than 10-8 ms-1, water is likely to percolate through the monolith rather than flow around it. In such cases, relating the release to the geometric surface can lead to misinterpretation. A percolation test is then more appropriate (e. g. CEN/TS 14405). This procedure may not be applicable to materials reacting with the leachant, leading for example to excessive gas emission or an excessive heat release. This document has been developed to determine the release of mainly inorganic constituents from wastes. It does not take into account the particular characteristics of organic constituents nor the consequences of microbiological processes in organic degradable wastes.
Characterization of waste. Leaching behaviour test for basic characterization. Dynamic monolithic leaching test with continuous leachant renewal under conditions relevant for specified scenario(s)
- ICS
- 13.030.10
- CCS
- Z27
- 发布
- 2015-11
- 实施
Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions; German version EN 15863:2015
- ICS
- 13.030.10
- CCS
- Z12
- 发布
- 2015-06
- 实施
Characterization of waste. Leaching behaviour test for basic characterization. Dynamic monolithic leaching test with periodic leachant renewal, under fixed conditions
- ICS
- 13.030.10
- CCS
- Z68
- 发布
- 2015-04-30
- 实施
- 2015-04-30
This European Standard is applicable for determining the leaching behaviour of monolithic wastes under dynamic conditions. The test is performed under fixed experimental conditions in this document. This test is aimed at determining the release as a function of time of inorganic constituents from a monolithic waste, when it is put into contact with an aqueous solution (leachant). This dynamic monolithic leaching test (DMLT) is a parameter specific test as specified in EN 12920 and is therefore not aimed at simulating real situations. The application of this test method alone is not sufficient for the determination of the detailed leaching behaviour of a monolithic waste under specified conditions. In the framework of EN 12920 and in combination with additional chemical information, the test results are used to identify the leaching mechanisms and their relative importance. The intrinsic properties can be used to predict the release of constituents at a given time frame, in order to assess the leaching behaviour of monolithic waste materials, placed in different situations or scenarios (including disposal and recycling scenarios). The test method applies to regularly shaped test portions of monolithic wastes with minimum dimensions of 40 mm in all directions that are assumed to maintain their integrity over a time frame relevant for the considered scenario. The test method applies to test portions for which the geometric surface area can be determined with the help of simple geometric equations. The test method applies to low permeable monolithic materials. Within the reproducibility ranges, the leaching results obtained with EN 15863 are expected to be equivalent to those obtained with CEN/TS 16637-2 (DMLT for construction products), because the main testing conditions are equalized in both standards. As shown in the results obtained with EN 15863, they are also demonstrated to be comparable with US EPA method 1315 (SW846).
Characterization of waste - Leaching behaviour test for basic characterization - Dynamic monolithic leaching test with periodic leachant renewal@ under fixed conditions
- ICS
- 13.030.10
- CCS
- Z12
- 发布
- 2015-04
- 实施
Characterisation of waste. Test methods for the determination of the monolithic status of waste
- ICS
- 13.030.10
- CCS
- Z27
- 发布
- 2014-09-30
- 实施
- 2014-09-30
This Technical Specification provides methods, which can be used to assess the monolithic character of a stabilised/solidified waste, with respect to landfilling. Information on the monolithic character is required to enable the choice of appropriate leaching tests for determination of the release of different substances from stabilised/solidified waste under specified (landfilling) conditions. This document includes several physical and/or chemical test methods each addressing different aspects of monolithic character. The selection of methods required for an assessment of the monolithic character of a stabilised/solidified waste may vary, depending on the scenario to be addressed or it may be specified in regulation. Rather than describing the procedures and methods in detail this document refers to existing standards and provides some guidance on their use on stabilised/solidified waste materials. This Technical Specification does not address issues related to health and safety. The following procedures and methods are included in this document: test to determine unconfined compressive strength; - test to determine permeability; - test to determine the loss of mass by dissolution or disintegration; - test to determine expansion; - test to determine the content of organic matter; - test to determine freeze/thaw effects.
Characterisation of waste - Test methods for the determination of the monolithic status of waste
- ICS
- 13.030.10
- CCS
- 发布
- 2014-09
- 实施
本标准规定了废旧电池回收处理场地的总体要求及选址和各功能区域的一般性要求。
Site Requirements for Recycling and Disposal of Used Batteries
- ICS
- 13.030.10
- CCS
- Z70
- 发布
- 2014-08-14
- 实施
- 2014-11-14
标准规定了回收利用废旧动力蓄电池的术语、定义，基本要求和技术条件，包括预处理、再生利用、环保要求。 本标准适用于电动汽车用废旧锂离子蓄电池、金属氢化物镍蓄电池的回收利用，其他电池可参照使用。
Technical conditions for the recycling of traction batteries for electric vehicles
- ICS
- 13.030.10
- CCS
- Z70
- 发布
- 2014-08-14
- 实施
- 2014-11-14
本标准规定了小型二次电池制造过程废料的术语和定义、一般要求、收集、贮存和运输、处理、污染控制方面的要求。 本标准适用于小型二次锂离子电池和镍氢电池在生产过程中产生废料的回收处理，其它电池生产过程中产生的废料可参照执行。
Requirements for waste recycling and treatment in the manufacturing process of small secondary batteries
- ICS
- 13.030.10
- CCS
- Z70
- 发布
- 2014-08-14
- 实施
- 2014-11-14
This standard prescribes the minimum requirements for the design, site selection, operation, maintenance, and closure of Class II and Class III solid waste landfill sites operated by the Client or its contractor. This standard does not apply to Class I (hazardous waste) landfill sites.
Petroleum and natural gas industries – Solid Waste Landfill Standard
- ICS
- 13.030.10
- CCS
- 发布
- 2014-08-06
- 实施
Technical specification for harmless treatment of toxic and harmful feed
- ICS
- 13.030.10
- CCS
- B 46
- 发布
- 2014-07-05
- 实施
- 2014-09-05
Specifications for construction, environmental supervision and acceptance of anti-seepage system for general industrial solid waste storage and disposal sites in Guizhou Province
- ICS
- 13.030.10
- CCS
- Z 70
- 发布
- 2014-06-10
- 实施
- 2014-07-10
