13.030.20 液态废物、淤泥 标准查询与下载

ASTM F2363/F2363M-17 污水和灰水流过处理系统的标准规范

1.1 This specification covers the design, manufacture, performance, operation, and testing of flow through treatment systems intended to process sewage or graywater, or both, generated during a ship’s normal service. This specification is intended for use by designers, manufacturers, purchasers, and operators of shipboard environmental pollution control equipment to determine the requirements for equipment design, manufacture, purchase, and in-service operation. 1.2 The treatment system shall be capable of meeting the effluent requirements detailed in Section 4 with respect to a ship’s operational area. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Sewage and Graywater Flow Through Treatment Systems

HG/T 5206-2017 氟硅酸钠生产废液处理处置方法

Sodium fluorosilicate production waste liquid treatment and disposal methods

HG/T 5207-2017 化学镀镍废液处理处置方法

Chemical nickel plating waste liquid treatment and disposal methods

ASTM D7066-04(2017) 氯三氟乙烯（S-316）的二聚体/三聚体的标准测试方法红外测定可回收油和油脂和非极性材料

1.1 This test method covers the determination of oil and grease and nonpolar material in water and wastewater by an infrared (IR) determination of dimer/trimer of chlorotrifluoroethylene (S-316)2 extractable substances from an acidified sample. Included in this estimation of oil and grease are any other compounds soluble in the solvent. 1.2 This test method is applicable to measurement of the light fuel although loss of some light ends during extraction can be expected. 1.3 This test method defines oil and grease in water and wastewater as that which is extractable in the test method and measured by IR absorption at 2930 cm-1 or 3.4 microns. Similarly, this test method defines nonpolar material in water and wastewater as that oil and grease which is not adsorbed by silica gel in the test method and measured by IR absorption at 2930 cm-1 . 1.4 This test method covers the range of 5 to 100 mg/L and may be extended to a lower or higher level by extraction of a larger or smaller sample volume collected separately. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine (Guide D3856) the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for dimer/trimer of chlorotrifluoroethylene (S-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination

T/GDES 8-2017 生态工业园区 电镀废水零排放 通用技术要求

1、生产企业废水分流 2、废水处理 3、废水的回用率 4、回用水的输出与使用 5、危险废物

General technical requirements for zero discharge of electroplating waste water in eco-industrial park

T/GDES 10-2017 生态工业园区 电镀废水零排放技术规范 镀锌企业

1、生产工艺要求 2、镀锌工艺要求 3、锌的利用率 4、生产过程控制 5、企业废水分流 6、水的回用和补充

Technical requirements for zero discharge of electroplating wastewater in eco - industrial park（Galvanized enterprise）

T/GDES 9-2017 生态工业园区 电镀废水零排放技术规范 镀镍企业

1、镀镍工艺要求 2、镍的利用率 3、生产过程控制 4、企业废水分流 5、水的回用和补充

Technical requirements for zero discharge of electroplating wastewater in eco - industrial park（Galvanized enterprise）

DIN EN 16720-1:2016 污泥特性描述. 物理一致性. 第1部分: 流动性测定. 挤压管装置法; 德文版本EN 16720-1-2016

Characterization of sludges - Physical consistency - Part 1: Determination of flowability - Method by extrusion tube apparatus; German version EN 16720-1:2016

DB35/T 1597-2016 温排水监测技术规范

本标准规定了温排水的监测方法、技术要求和自动监测设施的运营维护管理办法。 本标准适用于向江河、湖泊、水库、海域等具有使用功能的水体排放温水，导致表层水体温度升高的监测。

Technical specification for temperature and drainage monitoring

HG/T 5015-2016 含镍废液处理处置方法

本标准规定了含镍废液处理处置方法、环境保护和安全要求。 本标准适用于含镍废液的处理处置。

Treatment and disposal method for nickel waste liquid

BS EN 16720-1:2016 污泥特性描述. 物理一致性. 流动性测定. 挤压管装置法

Characterization of sludges. Physical consistency. Determination of flowability. Method by extrusion tube apparatus

EN 16720-1:2016 表征污泥-物理一致性-第1部分:测定流动性-采用挤出管法

This part of the European Standard specifies a method for determining the flowability, as defined in CEN/TR 15463, of sludge by means of the extrusion tube apparatus. This part of this European Standard is applicable to sludge and sludge suspensions from: storm water handling; urban wastewater collecting systems; urban wastewater treatment plants; plants treating industrial wastewater similar to urban wastewater (as defined in Directive 91/271/EEC); water supply treatment plants. This method is also applicable to sludge and sludge suspensions of other origins.

Characterization of sludges - Physical consistency - Part 1: Determination of flowability - Method by extrusion tube apparatus

CJ/T 485-2015 生活垃圾渗沥液卷式反渗透设备

本标准规定了生活垃圾渗沥液卷式反渗透设备(以下简称设备)的术语和定义、型号与标记、材料、使用条件、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于处理生活垃圾渗沥液的卷式反渗透设备。

Spiral reverse osmosis membrane equipment for municipal solid waste leachate treatment

HG/T 4838-2015 酯类物质泄漏的处理处置方法

本标准告知了酯类物质的理化性质和危害性，规定了发生酯类物质泄漏时的紧急措施、泄漏现场的处理方法和泄漏现场的处置方法。 本标准适用于GB 12268-2012第3类、第5类5.2项、第6类6.1项和第8类包含的酯类物质在贮存、生产、使用、经营、运输等过程中发生泄漏时的处理、处置。

Treatment and disposal method for ester substance

HG/T 4839-2015 醚类物质泄漏的处理处置方法

本标准告知了醚类物质的理化性质和危害性，规定了发生醚类物质泄漏时的紧急措施、泄漏现场的处理方法和泄漏现场的处置方法。 本标准适用于GB 12268-2012包括的第2.1类、第3类、第4.3类、第6.1类和第8类醚类物质在生产、贮存、使用、经营和运输等过程中发生泄漏时的处理、处置。

Treatment and disposal method for ethers spill

HG/T 4841-2015 苯胺泄漏的处理处置方法

本标准告知了苯胺的理化性质和危害性，规定了发生苯胺泄漏时的紧急措施、泄漏现场的处理方法和泄漏现场的处置方法。 本标准适用于苯胺在生产、贮存、使用、经营和运输等过程中发生泄漏时的处理、处置。

Treatment and disposal method for aniline spill

ITU-T Y SUPP 38-2015 ITU-T Y.4050-Y.4099 可持续智慧城市 定义分析

ITU-T Y.4050-Y.4099 - Smart sustainable cities - An analysis of definitions

DB21/T 2535-2015 城镇污水处理企业安全生产标准化评定

Standardization assessment of safety production in urban sewage treatment enterprises

DIN EN 14742:2015 污泥的特性.试验室化学条件程序;德文版本EN 14742-2015

Characterization of sludges - Laboratory chemical conditioning procedure; German version EN 14742:2015

BS EN 14742:2015 污泥特性 实验室化学调节程序

Characterization of sludges. Laboratory chemical conditioning procedure