13.030.20 液态废物、淤泥 标准查询与下载

PD CEN/TR 15126:2005 污泥的特性.污泥和污泥处理残留物掩埋的良好措施

This CEN Technical Report gives one of a series of sludge management options and describes good practice forThe disposal of sludges and sludge treatment residues to landfill where national regulations permit.This document is applicable toThe sludges described inThe scope of CEN/TC 308, i.e. specifically derived from:storm water handling; night soil; urban wastewater collecting systems; urban wastewater treatment plants; treating industrial wastewater similar to urban wastewater (as defined in Directive 91/271/EEC); water supply treatment plants; water distribution systems; but excluding hazardous sludges from industry.

Characterization of sludges - Good practice for landfilling of sludges and sludge treatment residues

DS/CEN/TR 13767:2005 污泥的特性 有或没有油脂和筛分的污泥焚烧的良好做法

This CEN Report describes good practice for the incineration of sludges with and without grease and screenings.This CEN Report is applicable for sludges described in the scope of CEN/TC 308 specifically derived from :- night soil ;- urban wastewater collecting systems ;- urban wastewater treatment plants ;- treating industrial wastewater similar to urban wastewater (as defined in Directive 91/271/EC) ;but excluding hazardous sludges from industry.This European standard is not applicable to co-incineration of sludge and other wastes, (either urban or hazardous) (see CR 13768) and to the use of sludge in cement kilns.Annex A gives tables of data for different

Characterisation of sludges - Good practice for sludges incineration with and without grease and screenings

DS/CEN/TR 13768:2005 污泥的特性 污泥和生活垃圾联合焚烧的优良作法

This CEN Report gives indication for dealing of the combined incineration treatment of sludge and household waste.This European standard is applicable to sludges described in the scope of CEN/TC 308 i.e. specifically derived from :- storm water handling ;- night soil ;- urban wastewater collecting systems ;- urban wastewater treatment plants ;- treating industrial wastewater similar to urban wastewater (as defined in Directive 91/271/EEC ) ;but excluding hazardous sludges from industry.Annex A gives information on various systems to input sludge into a household waste incineration plant.

Characterisation of sludges - Good practice for combined incineration of sludges and household wastes

BS PD CEN/TR 13767:2004 污物特性.含有和/或不含润滑脂和筛屑的污物焚烧实施规程

This document describes good practice for the incineration of sludges with and without grease and screenings. This document is applicable for sludges described in the scope of CEN/TC 308 specifically derived from : ? night soil ; ? urban wastewater collecting systems ; ? urban wastewater treatment plants ; ? treatment of industrial wastewater similar to urban wastewater (as defined in Directive 91/271/EC) ; but excluding hazardous sludges from industry. This document is not applicable to co-incineration of sludge and other wastes, (either urban or hazardous) (see CEN/TR 13768) and to the use of sludge in cement kilns. Annex A gives tables of data for different typical parameters for sludge, furnace and ash.

Characterisation of sludges - Good practice for sludges incineration with and without grease and screenings

ANSI/ASTM D7066:2004 用红外测定法测定三氟氯乙烯(s-316)可回收石油和润滑脂及非极性材料的二聚物/三聚物的试验方法

This test method covers the determination of oil and grease and nonpolar material in water and wastewater by an infrared (IR) determination of dimer/trimer of chlorotrifluoroethylene (S-316) extractable substances from an acidified sample. Included in this estimation of oil and grease are any other compounds soluble in the solvent. The method is applicable to measurement of the light fuel although loss of some light ends during extraction can be expected. This method defines oil and grease in water and wastewater as that which is extractable in the test method and measured by IR absorption at 2930 cm- or 3.4 microns. Similarly, this test method defines nonpolar material in water and wastewater as that oil and grease which is not adsorbed by silica gel in the test method and measured by IR absorption at 2930 cm-. This method covers the range of 5 to 100 mg/L and may be extended to a lower or higher level by extraction of a larger or smaller sample volume collected separately. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine (D 3856 Guide for Good Laboratory Practices) the applicability of regulatory limitations prior to use.

Test Method for Dimer/Trimer of Chlorotrifluoroethylene (s-316) Recoverable Oil and Grease and Nonpolar Material by Infrared Determination

ASTM D5495-03(2011) 混合废水液体采样器(COLIWASA)采样检查的标准操作规程

This practice is applicable to sampling liquid wastes and other stratified liquids. The COLIWASA is used to obtain a vertical column of liquid representing an accurate cross-section of the sampled material. To obtain a representative sample of stratified liquids, the COLIWASA should be open at both ends so that material flows through it as it is slowly lowered to the desired sampling depth. The COLIWASA must not be lowered with the stopper in place. Opening the stopper after the tube is submerged will cause material to flow in from the bottom layer only, resulting in gross over-representation of that layer. This practice is to be used by personnel acquiring samples. This practice should be used in conjunction with Guide D4687 which covers sampling plans, safety, QA, preservation, decontamination, labeling and chain-of-custody procedures; Practice D5088 which covers decontamination of field equipment used at waste sites; Practice D5283 which covers project specifications and practices for environmental field operations, and Practice D5743 which covers drum sampling..1.1 This practice describes the procedure for sampling liquids with the composite liquid waste sampler, or “COLIWASA.” The COLIWASA is an appropriate device for obtaining a representative sample from stratified or unstratified liquids. Its most common use is for sampling containerized liquids, such as tanks, barrels, and drums. It may also be used for pools and other open bodies of stagnant liquid. Note 18212;A limitation of the COLIWASA is that the stopper mechanism may not allow collection of approximately the bottom inch of material, depending on construction of the stopper. 1.2 The COLIWASA should not be used to sample flowing or moving liquids. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Sampling With a Composite Liquid Waste Sampler (COLIWASA)

DS/EN 12457-1:2002 废弃物的特性 浸出 颗粒状废料和污泥浸出的符合性试验 第1部分：对于固体含量高且粒径小于 4 毫米的材料（无

This part of four standards specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ration of 2 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction (as specified in 4.3.2) This standard has been developed to investigate mainly inorganic constituents from wastes. It does not take into account the particular characteristics of non-polar organic constituents nor the consequences of microbiological processes in organic degradable wastes.

Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 1: One stage batch test at a liquid to solid ratio of 2 l/kg for materials with high solid content and with particle size below 4 mm (withou

DS/EN 12457-2:2002 废物表征 浸出 颗粒废料和污泥浸出的符合性测试 第2部分：对于粒径低于 4 毫米的材料（没有或有尺寸减小），液固比为 10 升/千克的阶段批量测试

This part of four standards specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ration of 10 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction (as specified in 4.3.2). This standard has been developed to investigate mainly inorganic constituents from wastes. It does not take into account the particular characteristics of non-polar organic constituents nor the consequences of microbiological processes in organic degradable wastes.

Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 4 mm (without or with size reduction)

DS/EN 12457-4:2002 废物表征 浸出 颗粒废料和污泥浸出的符合性测试 第4部分：对于粒径小于 10 毫米的材料（没有或有尺寸减小），液固比为 10 升/千克的阶段批量测试

This part of four standards specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 10 l/kg dry matter. It applies to waste which has a particle size below 10 mm without or with size reduction. This standard has been developed to investigate mainly inorganic constituents from wastes. It does not take into account the particular characteristics of non-polar organic constituents nor the consequences of microbiological processes in organic degradable wastes.

Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10 mm (without or with size reduction)

DS/EN 12457-3:2002 废物表征 浸出 颗粒废料和污泥浸出的符合性试验 第3部分：对于高固体含量和颗粒尺寸的材料，液固比为 2 l/kg 和 8 l/kg 的两阶段分批试验低于 4

This part of the standard specifies a compliance test providing information on leaching of granular wastes and sludges under the experimental conditions specified hereafter, and particularly a liquid to solid ratio of 2 l/kg dry matter and subsequently of 8 l/kg dry matter. It applies to waste which has a particle size below 4 mm without or with size reduction. This standard has been developed to investigate mainly inorganic constituents from wastes. It does not take into account the particular characteristics of non-polar organic constituents nor the consequences of microbiological processes in organic degradable wastes.

Characterisation of waste - Leaching - Compliance test for leaching of granular waste materials and sludges - Part 3: Two stage batch test at a liquid to solid ratio of 2 l/kg and 8 l/kg for materials with high solid content and with particle size below 4

LST EN 12879-2002 污泥的表征 干质量烧失量的测定

Characterization of sludges - Determination of the loss on ignition of dry mass

LST EN 13346-2002 污泥的表征 微量元素和磷的测定 王水提取法

Characterization of sludges - Determination of trace elements and phosphorus - Aqua regia extraction methods

LST EN 12880-2002 污泥的表征 干残渣和含水量的测定

Characterization of sludges - Determination of dry residue and water content

LST EN 13342-2002 污泥的表征 凯氏氮的测定

Characterization of sludges - Determination of Kjeldahl nitrogen

PD CR 13767-2001 污物特性.含有和/或不含润滑脂和筛屑的污物焚烧实施规程

Characterization of sludges. Good practice for sludges incineration with and without grease and screenings

ASTM D6699-01 使用调料器取样液体的标准做法

1.1 This practice covers the procedure for sampling stratified or un-stratified waters and liquid waste using bailers.1.2 Three specific bailers are discussed in this practice. The bailers are the single and double check valve and differential pressure.1.3 This standard does not cover all of the bailing devices available to the user. The bailers chosen for this practice are typical of those commercially available.1.4 This practice should be used in conjunction with Guide D4687, Practice D5088, and Practice D5283.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Sampling Liquids Using Bailers

DS/EN 12879:2001 污泥的表征 干质量烧失量的测定

This Standard specifies a method for the determination of the loss on ignition of dry mass of sludges and sludge products at 550 ºC after the dry residues have been determined in accordance with the method of EN 12880.

Characterization of sludges - Determination of the loss on ignition of dry mass

DS/EN 12880:2001 污泥的表征 干残渣和含水量的测定

This standard specifies a method for the determination of dry residue and water content of sludge and sludge products.

Characterization of sludges - Determination of dry residue and water content

PD CR 13097-2001 污泥的特性.农业中应用的良好实践

Characterization of Sludges - Good Practice for Utilisation in Agriculture

NP EN 12176-2000 矿泥的属性．pH值的测量

Characterization of sludge Determination of pH-value