13.040.01 空气质量综合 标准查询与下载

LST EN ISO 14956:2004 空气质量 通过与所需的测量不确定度比较来评估测量程序的适用性（ISO 14956:2002）

Air quality - Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty (ISO 14956:2002)

ASTM D7036-04 空气排放检测机构能力标准实践

This practice establishes general criteria for a quality system that, when followed, helps ensure consistently acceptable data quality from an AETB. The relevant criteria contained in this practice shall be addressed in the AETB’s quality manual, which shall contain or refer to additional specific criteria and requirements where relevant and necessary. The quality manual and its implementation (including test protocols, reports, and personnel testing) shall provide the sole basis for determining the conformance of the AETB with this standard. Note 38212;This practice assesses the overall ability of an AETB to deliver data of known and documented quality on a consistent basis regardless of the test method used. There is no requirement to define a scope of testing. It is a requirement of this practice that prior to performing a test method for the first time, the AETB has in place resources, training, and QA/QC consistent with this practice to insure data of acceptable quality are produced. This practice is for use by AETBs in developing the quality, administrative, and technical systems that govern their operations. Clients, regulatory authorities, and accreditation bodies may also use it in confirming or recognizing the competency of AETBs. Note 48212;This practice is performance-based; that is, it focuses on the actual performance (that is, consistent generation of data of known and documented quality) of the AETB rather than on an extensive collection of prescriptive criteria that may or may not be relevant to a particular AETB. It also focuses on the education and qualifications of the individual tester. Note 58212;There has been an effort in the development of this practice to keep the paperwork and administrative burdens on affected AETBs to the minimum required for an effective program.1.1 This practice specifies the general requirements for competence to carry out sampling and analysis for air emissions tests of stationary sources. It covers testing and calibration performed using standard methods, non-standard methods and methods developed by the AETB.1.2 This practice is applicable to all bodies engaged in air emission testing regardless of the number of personnel or the scope of testing activities. When an AETB does not undertake one or more of the activities covered by the practice such as developing test methods, the requirements of those clauses do not apply.1.3 The notes given provide clarification of text, examples, and guidance. The notes do not contain requirements and do not form an integral part of this practice.Note 18212;ISO/IEC 17025 has been considered when elaborating this practice. It is to be noted that at the time of approval of this practice ISO/IEC 17025 was under revision. Several, but not all, statements of this practice are consistent with ISO/IEC 17025:1999.Note 28212;This practice is a specification for competence. It does not address accreditation or any activities specific to accreditation such as on-site inspections/audits by external assessors or proficiency testing.

Standard Practice for Competence of Air Emission Testing Bodies

BS 1339-3:2004 湿度.湿度测量指南

This British Standard gives guidance on the selection and use of instruments for the measurement of humidity. It introduces the main concepts and practical techniques involved in measuring humidity in air and other "inert" gases and provides an explanation of how to make valid and meaningful measurements. It also includes guidance on specifying or choosing appropriate equipment for a known application.

Humidity — Part 3: Guide to the measurement of humidity

LST EN ISO 16017-2:2004 室内、环境和工作场所空气 通过吸附管/热脱附/毛细管气相色谱法对挥发性有机化合物的采样和分析 第2部分：扩散采样（ISO 16017-2:2003）

Indoor, ambient and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography - Part 2: Diffusive sampling (ISO 16017-2:2003)

ASTM D7036-04(2011) 气体辐射测试机构的能力的标准操作规程

This practice establishes general criteria for a quality system that, when followed, helps ensure consistently acceptable data quality from an AETB. The relevant criteria contained in this practice shall be addressed in the AETB’s quality manual, which shall contain or refer to additional specific criteria and requirements where relevant and necessary. The quality manual and its implementation (including test protocols, reports, and personnel testing) shall provide the sole basis for determining the conformance of the AETB with this standard. Note 38212;This practice assesses the overall ability of an AETB to deliver data of known and documented quality on a consistent basis regardless of the test method used. There is no requirement to define a scope of testing. It is a requirement of this practice that prior to performing a test method for the first time, the AETB has in place resources, training, and QA/QC consistent with this practice to insure data of acceptable quality are produced. This practice is for use by AETBs in developing the quality, administrative, and technical systems that govern their operations. Clients, regulatory authorities, and accreditation bodies may also use it in confirming or recognizing the competency of AETBs. Note 48212;This practice is performance-based; that is, it focuses on the actual performance (that is, consistent generation of data of known and documented quality) of the AETB rather than on an extensive collection of prescriptive criteria that may or may not be relevant to a particular AETB. It also focuses on the education and qualifications of the individual tester. Note 58212;There has been an effort in the development of this practice to keep the paperwork and administrative burdens on affected AETBs to the minimum required for an effective program.1.1 This practice specifies the general requirements for competence to carry out sampling and analysis for air emissions tests of stationary sources. It covers testing and calibration performed using standard methods, non-standard methods and methods developed by the AETB. 1.2 This practice is applicable to all bodies engaged in air emission testing regardless of the number of personnel or the scope of testing activities. When an AETB does not undertake one or more of the activities covered by the practice such as developing test methods, the requirements of those clauses do not apply. 1.3 The notes given provide clarification of text, examples, and guidance. The notes do not contain requirements and do not form an integral part of this practice. Note 18212;ISO/IEC 17025 has been considered when elaborating this practice. It is to be noted that at the time of approval of this practice ISO/IEC 17025 was under revision. Several, but not all, statements of this practice are consistent with ISO/IEC 17025:1999. Note 28212;This practice is a specification for competence. It does not address accreditation or any activities specific to accreditation such as on-site inspections/audits by external assessors or proficiency testing.

Standard Practice for Competence of Air Emission Testing Bodies

UL 2034 BULLETINS-2004 （草稿）2/26/2004（112p）

Clarification of Marking to Indicate Approval for Marine Use, Clarification of Instructions for Marine Use Alarms, Establishment of End-of-Life Requirements, Additional CO Performance Test.

(Draft)2/26/2004 (112p)

DS/EN ISO 16017-2:2003 室内、环境和工作场所空气 通过吸附管/热脱附/毛细管气相色谱法对挥发性有机化合物的采样和分析 第2部分：扩散采样

This part of ISO 16017 gives general guidance for the sampling and analysis of volatile organic compounds (VOCs) in air. It is applicable to indoor, ambient and workplace air. This part of ISO 16017 is applicable to a wide range of VOCs, including hydrocarbons, halogenated hydrocarbons, ester, glycol ethers, ketones and alcohols. A number of sorbents1) are recommended for the sampling of these VOCs, each sorbent having a different range of applicability. Very polar compounds generally require derivatisation; very low boiling compounds are only partially retained by the sorbents and can only be estimated qualitatively. Semi-volatile compounds are fully retai

Indoor, ambient and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography - Part 2: Diffusive sampling

DS/EN 13725:2003 空气质量 动态嗅觉法测定气味浓度

This standard specifies a method for the objective determination of the odour concentration of a gaseous sample using dynamic olfactometry with human assessors and the emission rate of odours emanating from point sources, area sources with outward flow and area sources without outward flow. The primary application is to provide a common basis for evaluation of odou emissions in the member states of the European Union.

Air quality - Determination of odour concentration by dynamic olfactometry

DIN EN ISO 16017-2:2003 室内、环境和工作场所空气.用吸附管/热解吸/毛细管气相色谱法对挥发性有机化合物的取样及分析.第2部分:扩散取样

This standard gives general guidance for the sampling and analysis of volatile organic compounds (VOCs) in air by diffusive sampling. It is applicable to ambient, indoor and workplace atmospheres. This standard is appropriate for the determination of a wide range of VOCs, including hydrocarbons, halogenated hydrocarbons, esters, glycol ethers, ketones and alcohols. A number of sorbents are recommended for the sampling of these VOCs, each sorbent having a different range of applicability.#,,#

Indoor, ambient and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography - Part 2: Diffusive sampling (ISO 16017-2:2003); German version EN ISO 16017-2:2003

BS EN ISO 16017-2:2003 室内、环境和工作场所空气.用吸附管/热解吸/毛细管气相色谱法作挥发性有机化合物的取样及分析.扩散取样

ISO 16017-2:2003 gives general guidance for the sampling and analysis of volatile organic compounds (VOCs) in air. It is applicable to indoor, ambient and workplace air. ISO 16017-2:2003 is applicable to a wide range of VOCs, including hydrocarbons, halogenated hydrocarbons, ester, glycol ethers, ketones and alcohols. A number of sorbents are recommended for the sampling of these VOCs, each sorbent having a different range of applicability. Very polar compounds generally require derivatisation; very low boiling compounds are only partially retained by the sorbents and can only be estimated qualitatively. Semi-volatile compounds are fully retained by the sorbents, but may only be partially recovered. ISO 16017-2:2003 is applicable to the measurement of airborne vapours of VOCs in a concentration range of approximately 0,002 mg/m3 to 100 mg/m3 individual organic for an exposure time of 8 h, or 0,3 g/m3 to 300 g/m3 individual organic for an exposure time of four weeks. The upper limit of the useful range is set by the sorptive capacity of the sorbent used and by the linear dynamic range of the gas chromatograph column and detector or by the sample splitting capability of the analytical instrumentation used. The lower limit of the useful range depends on the noise level of the detector and on blank levels of analyte and/or interfering artefacts on the sorbent tubes. Artefacts are typically sub-nanogram for well-conditioned Tenax GR and carbonaceous sorbents, carbonized molecular sieves and pure charcoals; at low nanogram levels for Tenax TA and at 5 ng to 50 ng levels for other porous polymers.

Indoor, ambient and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography - Diffusive sampling

EN ISO 16017-2:2003 室内,周围和工作场所空气用吸附管/热解吸/毛细管气相色谱法作挥发性有机化合物的取样及分析.第2部分:扩散取样ISO 16017-2-2003

Indoor, ambient and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography - Part 2: Diffusive sampling

ISO 16017-2:2003 室内、环境和工作场所空气.用吸附管/热解吸/毛细管气相色谱法作挥发性有机化合物的取样及分析 第2部分:扩散取样

This part of ISO 16017 gives general guidance for the sampling and analysis of volatile organic compounds (VOCs) in air. It is applicable to indoor, ambient and workplace air. This part of ISO 16017 is applicable to a wide range of VOCs, including hydrocarbons, halogenated hydrocarbons, esters, glycol ethers, ketones and alcohols. A number of sorbents are recommended for the sampling of these VOCs, each sorbent having a different range of applicability. Very polar compounds generally require derivatisation; very low boiling compounds are only partially retained by the sorbents and can only be estimated qualitatively. Semi-volatile compounds are fully retained by the sorbents, but may only be partially recovered. This part of ISO 16017 is applicable to the measurement of airborne vapours of VOCs in a mass concentration range of approximately 0,002 mg/m to 100 mg/m individual organic for an exposure time of 8 h, or 0,3 μg/m to 300 μg/m individual organic for an exposure time of four weeks. The upper limit of the useful range is set by the sorptive capacity of the sorbent used and by the linear dynamic range of the gas chromatograph column and detector or by the sample splitting capability of the analytical instrumentation used. The lower limit of the useful range depends on the noise level of the detector and on blank levels of analyte and/or interfering artefacts on the sorbent tubes. Artefacts are typically sub-nanogram for well-conditioned Tenax GR and carbonaceous sorbents such as Carbopack/Carbotrap type materials, carbonized molecular sieves such as Spherocarb and pure charcoals. Artefacts are typically at low nanogram levels for Tenax TA and at 5 ng to 50 ng levels for other porous polymers such as Chromosorbs and Porapaks. note: 1) The sorbents listed in Annex B and elsewhere in this part of ISO 16017 are those known to perform as specified under this part of ISO 16017. Each sorbent or product that is identified by a trademarked name is unique and has a sole manufacturer; however, they are widely available from many different suppliers. This information is given for the convenience of users of this part of ISO 16017 and does not constitute an endorsement by ISO of the product named. Equivalent products may be used if they can be shown to lead to the same results.

Indoor, ambient and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography - Part 2: Diffusive sampling

ASTM D5011-92(2003) 用传输标准校准臭氧监测仪的标准实践

Standard Practices for Calibration of Ozone Monitors Using Transfer Standards

DS/EN ISO 14956:2003 空气质量 通过与所需的测量不确定度比较来评估测量程序的适用性

This International Standard specifies, for the field of air quality procedures, the: - estimatation of measurement uncertainty from actual or claimed values of all important performance characteristics of a method under stationary conditions; - assessment of whether or not specified values for these performance characteristics comply with the required quality of a measured value at a stated measure and value; - evaluation of the applicability of the measurement method based on laboratory performance and confirmatory field test; - establishment of requirements on dynamic behaviour of instruments. This International Standard is applicable to measurement proce

Air quality - Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty

DS/ISO 11222:2003 空气质量 空气质量测量时间平均值不确定度的测定

This standard provides a method for the quantification of the uncertainty of a time average of a set of air quality data obtained at a specified location over a defined averaging time period. The method is applicable to air quality data obtained by continuous or intermittent monitoring by means of a specified measuring system. The uncertainty of the time average depends on both the uncertainty of the measurement results and the uncertainty due to incomplete time coverage of the data set.

Air quality - Determination of the uncertainty of the time average of air quality measurements

DIN EN ISO 14956:2003 空气质量.比照规定的测量不确定度评价测量规程的适用性

This International Standard specifies the procedure to estimate measurement uncertainty from actual or claimed values of all important performance characteristics of a method under stationary conditions. It allows to assess whether or not specified values for these performance characteristics comply with the required quality of a measured value at a stated measurand value. Furthermore, it includes procedures to evaluate the applicability of the measurement method based on laboratory performance and confirmatory field test and to establish requirements on dynamic behaviour of instruments. This International Standard is applicable to measurement procedures the output of which is a defined time average.#,,#

Air quality - Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty (ISO 14956:2002); German version EN ISO 14956:2002

UL 2034 BULLETINS-2003 （草稿）3/14/2003（16p）

Clarification of Marking to Indicate Approval for Marine Use, Clarification of Instructions for Marine Use Alarms, Establishment of End-of-Life Requirements, Additional CO Performance Test.

(Draft)3/14/2003 (16p)

LST EN ISO 16017-1:2002 室内、环境和工作场所空气 通过吸附管/热脱附/毛细管气相色谱法对挥发性有机化合物的采样和分析 第1部分：泵送采样（ISO 16017-1:2000）

Indoor, ambient and workplace air - Sampling and analysis of volatile organic compounds by sorbent tube/thermal desorption/capillary gas chromatography - Part 1: Pumped sampling (ISO 16017-1:2000)

DIN ISO 11222:2002 空气质量.空气质量测量时间平均值不确定度测定

This International Standard provides a method for the quantification of the uncertainty of a time average of a set of air quality data obtained at a specified location over a defined averaging time period. The air quality data may have been obtained by continuous or intermittent monitoring. The uncertainty of the time average depends on both the uncertainty of the measurement results and the uncertainty due to incomplete time coverage of the data set. The set of air quality data shall be representative of the temporal structure of the measurand. Information on the uncertainty of the measurement results shall be available. The influence of limited spatial coverage of data set on the uncertainty of the time average is not considered.

Air quality - Determination of the uncertainty of the time average of air quality measurements (ISO 11222:2002)

NF X43-504*NF ISO 11222:2002 空气质量.空气质量测量平均时间的不确定性的测定

Air quality - Determination of the uncertainty of the time average of air quality measurements.