13.060.10 天然水资源 标准查询与下载

ASTM F715-07(2023) 控制和储存漏油用涂层织物的标准试验方法

1.1 These test methods cover laboratory-conducted performance tests for coated fabrics used in spill control barriers or in temporary storage devices. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Coated Fabrics Used for Oil Spill Control and Storage

T/CAQI 326-2023 地表水资源质量动态评价技术规程

本文件规定了地表水资源质量监测数据收集与处理、动态评价指标体系构建、动态评价、动态变化规律分析等方面的技术要求。 本文件适用于全国水资源一级区和省级行政区地表水资源质量动态评价工作，评价单位时长为月。其他评价区域或评价时长（旬、周、日等）的地表水资源质量评价工作可参照执行。

Technical specification for dynamic assessment of surface water resources quality

DB32/T 4463-2023 水域状况评价规范

Standards for assessing the status of water areas

ASTM F1738-23 空中使用的溢油分散剂沉积测定的标准试验方法

1.1 This test method covers the measurement of the deposition of an aerially applied dispersant surrogate, typically dyed water, on the surface of the ground or water. The test method of obtaining these measurements is described, and the analysis of the results, in terms of dispersant use, is considered. There are a number of techniques that have been developed, and this test method outlines their application. These measurements can be used to confirm or verify the specifications of a given equipment set, its proper functioning, and use. 1.2 This test method is applicable to systems used with helicopters or airplanes. 1.3 This test method is one of four related to dispersant application systems. Guide F1413/F1413M covers design, Practice F1460/F1460M covers calibration, Test Method F1738 covers deposition, and Guide F1737/F1737M covers the use of the systems. Familiarity with all four standards is recommended. 1.4 There are some exposure and occupational health concerns regarding the methods described. These are not discussed in this test method since they are a function of dispersant formulation. Anyone undertaking such experiments should consult the occupational health experts of the dispersant manufacturer regarding the precautions to be used. 1.5 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Deposition of Aerially Applied Oil Spill Dispersants

T/CIDA 0017-2023 南方平原河网区稻田节水减排技术导则

前言　 1  范围　 2  规范性引用文件　 3  术语和定义　 4  总体技术要求　 5  稻田节水技术　 6  稻田污染源头减量技术　 7  稻田控制排水技术 8  沟渠退水减污技术 附录A（资料性） 南方平原河网区稻田节水减排技术路线 附录B(资料性） 南方平原河网区水稻种植肥料实施时间 附录C（资料性）南方平原河网区退水减污技术模式

Technical guide for water-saving irrigation and drainage reduction from paddy fields in the plain river network region in southern China

ASTM D5903-96(2023) 地下水取样事件的计划和准备标准指南

1.1 This guide covers planning and preparing for a groundwater sampling event. It includes technical and administrative considerations and procedures. Example checklists are also provided as Appendices. 1.2 This guide may not cover every consideration procedure, or both, that is necessary before all groundwater sampling projects. In karst or fractured rock terranes, it may be appropriate to collect groundwater samples from springs (see Guide D5717). This guide focuses on sampling of groundwater from monitoring wells; however, most of the guidance herein can apply to the sampling of springs as well. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Planning and Preparing for a Groundwater Sampling Event

T/CHES 86-2022 河湖水系连通水安全保障能力评价技术导则

主要技术内容包括资料收集与调查、河湖水系连通状态分析、河湖水系连通水安全保障能力分析和综合评价等

Technical Guidelines for Evaluation of Water Security Capabilities of Connected Rivers and Lakes Systems

T/JSSL 0005-2022 取用水管理技术规范

取水工程建设  取水工程建设主要包括取水口选址、取水水泵、阀门、进出水管道、泵房及视频监控等工程。 取水口选址应根据现场实际情况，符合 GB 50015 等相关技术规范要求。  取水口应按照批复的取水水源、取水地点、取水方式、取水规模等建设，公共供水的取水户应在 取水口附近设置防撞设施。  取水管道覆土厚度应符合 GB 50289 的要求，预留计量设施安装位置，示意图见附录 A。  取水管道材质选择应考虑承受内压和外荷载强度、耐腐蚀性能、使用年限、运输、施工和安装难 易程度、内壁光滑程度和价格以及自然地理环境等因素，并根据管材进行表面除锈处理。  取水水泵、阀门及进出水管道应安装规范、标识清晰。取水管道暴露于空气中的部分宜刷标准色， 推荐蓝色（R：0，G：0，B：255）或绿色（R：0，G：255，B：0）的油漆涂装，用白色油漆喷涂取 水户名称，并以箭头→标注水流方向。  地下水井应设置专用井台、水准点、水位观测孔等，井台安装示意图见附录 B，地下水井取水工 程建设应符合 DB 32/T 791 要求，水准点、水位观测孔设置应符合 GB/T 50138 要求。 取水工程宜设置专门取水泵房。泵房内应进行地面硬化处理，并设置护栏、扶手等安全设施和警 告标志，取水泵房具体设计参照 GB 50265 执行。取水口及取水泵房周边应建设必要的通行道路，设置 交通指示牌等标识，预留远程监控位置。取水口周边不得设置与取水无关的设施，并保持道路畅通、环 境干净整洁。  重点监管的取水口和县级以上集中式饮用水水源地取水口，应在取水口、泵房等位置安装 24 小时 视频监控设施，实时掌握现场情况。

Technical specification for the water intake management

DB3213/T 1041-2022 服务业用水定额

Water quota for service industry

DB3213/T 1042-2022 生活用水定额

Domestic water quota

ASTM F1788-22 水上泄漏油的现场燃烧标准导则:环境与操作依据

1.1 This guide covers the use of in-situ burning to assist in the control of oil spills on water. This guide is not applicable to in-situ burning of oil on land or the disposal of oil or oiled debris in incinerators. 1.2 The purpose of this guide is to provide information that will enable spill responders to decide if burning will be used as part of the oil spill cleanup response. Other standards address the use of ignition devices (Guide F1990), the use of fireresistant boom (Guide F2152), the use of burning in ice conditions (Guide F2230), the application of in-situ burning in ships (Guide F2533), and the use of in-situ burning in marshes (Guide F2823). 1.3 This is a general guide only. It is assumed that conditions at the spill site have been assessed and that these conditions are suitable for the burning of oil. It is also assumed that permission to burn the oil has been obtained from appropriate regulatory authorities. Variations in the behavior of different oil types are not dealt with and may change some of the parameters noted in this guide. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4.1 Exception—Alternate units are included in 7.5, 7.7, and 7.8. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for In-Situ Burning of Oil Spills on Water: Environmental and Operational Considerations

ASTM F625/F625M-94(2022) 泄漏控制系统水体分类标准实践

1.1 This practice creates a system of categories that classify water bodies relating to the control of spills of oil and other substances that float on or into a body of water. 1.2 This practice does not address the compatibility of spill control equipment with spill products. It is the user’s responsibility to ensure that any equipment selected is compatible with anticipated products. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Classifying Water Bodies for Spill Control Systems

T/JSSL 0002-2022 开发区水资源论证区域评估导则

《开发区水资源论证区域评估导则》包括范围、规范性 引用文件、术语和定义、一般规定、区域水资源条件分析、 开发区现状评估、水效分析、用水总量分析、水资源配置、 退水分析、取用水管理、评估结论和建议等 12 章内容和 7 个附录。 第 1 章～第 2 章：明确了《开发区水资源论证区域评估 导则》的适用范围与所引文件。 第 3 章：明确了相关术语与定义 第 4 章：规定了开发区水资源论证区域评估的评估工作 程序、工作开展的流程、分析范围、水平年及基本要求等内 容的相关要求。 第 5 章：规定了区域水资源条件分析的相关要求。 第 6 章：规定了开发区现状评估的相关要求。 第 7 章：规定了节水评价和水效评估的相关要求。 第 8 章：规定了需水预测和用水总量核定的相关要求。 第 9 章：规定了水资源配置和取水影响评估的相关要求。 第 10 章：规定了退水影响评估的相关要求。 第 11 章：规定了取用水管理与措施的相关要求。 第 12 章：规定了评估结论和建议的相关要求。 附录 A 为规范性附录：水资源论证区域评估报告书基本情况表 附录 B 为资料性附录：《水资源论证区域评估报告书》编写提纲 附录 C 为资料性附录：评估编制步骤图 附录 D 为资料性附录：基本资料 附录 E 为资料性附录：图件和附件要求 附录 F 为资料性附录：问题与措施清单样表 附录 G 为资料性附录：现状规划水平年行业和产品水效准入清单表

Guidelines for water resources demonstration regional assessment of development zone

DB32/T 4324-2022 河湖库利用变化高分遥感监测规范

Specifications for high-resolution remote sensing monitoring of river, lake and reservoir utilization changes

DB45/T 2513-2022 灌溉水有效利用系数测算规程

Rules for Calculation of Effective Utilization Coefficient of Irrigation Water

DB12/T 1121-2022 基坑降水水资源论证技术规程

Technical regulations for demonstration of precipitation water resources in foundation pits

DB37/T 4508-2022 地下水超采综合治理评估技术指南

Technical guidelines for comprehensive management and assessment of groundwater overexploitation

DB32/T 4178-2021 河流水生态监测规范

本文件适用于江苏省境内河流的水生态监测。

Specifications for River Ecological Monitoring

T/LNWTA 008-2021 剑水蚤污染水质特征监测技术规范

本标准规定识别水中剑水蚤方法的要求、检测范围、实验方法、检验规则。 本标准适用于监测野外天然水体，包括湖泊、水库、池塘、河流。

Technical specification for monitoring characteristics of water polluted by daphnia saxifera

DIN 38402-13:2021 德国水、废水和污泥检验标准方法 一般信息（A 组） 第13部分：地下水取样的设计和性能（A 13）

This standard provides guidelines for the planning and implementation of groundwater sampling to determine groundwater quality, to identify and assess groundwater contamination and to manage groundwater resources as well as protection and remediation measures.

German standard methods for the examination of water, waste water and sludge - General information (group A) - Part 13: Design and performance of the sampling of groundwater (A 13)