13.200 事故和灾害控制 标准查询与下载

T/SDHCIA 001-2020 化工园区突发公共卫生事件应急预案编制导则

 从术语和定义、应急预案编制程序、应急预案编制内容、预案格式和要求等方面，详细地规范了预案编制各个细节，重点包括： a）应急预案编制程序：前期准备、实地调查、应急预案编制及征求意见、评审、发布修订； b）应急预案编制内容：目的、编制依据、预案体系上下衔接、工作原则、事件分级、化工园区情况（工业园基本情况、园区内企业基本信息、主要公共卫生事件风险辨识、应急资源、应急信息库和应急能力等）、应急组织机构及职责、预防与预警、报警、信息报告、应急响应及措施、善后处置、保障措施、应急培训和演练、奖惩、预案评审、征求意见、备案、发布、修订、生效实施等。

Guidelines for compiling contingency plan for public health emergencies in chemical industrial parks

T/ZJBE 001-2020 电动自行车乘员头盔技术要求及检测规范

5　技术要求 5.1　结构 5.1.1　结构组成 电动自行车乘员头盔应由壳体、缓冲层、佩戴装置等组成；可配置护目镜、遮阳镜、防风围脖、舒适衬垫等配件。 5.1.2　壳体 电动自行车乘员头盔的壳体应满足以下技术要求： a) 表面应坚固、平滑，边沿应圆钝，不得在使用过程中伤及头部、颈部； b) 涂层应均匀，色泽鲜亮、光洁，无毛刺、裂纹、挂流、沾污、气泡及脱落现象发生； c)突出物应满足以下要求：   ——内表面可接触头型的部位，不应有超过2mm且半径小于1mm的突出物及尖锐物体；   ——铆钉应成辐射状，突出部分不应超过电动自行车乘员头盔外表面2mm；   ——外表面不应有超过5mm的外部突出物，但容易脱落的部件不在此限制内，如固定透气孔的装置，固定镜片的装置。 5.1.3　缓冲层 缓冲层应符合以下技术要求： a) 形状、规格尺寸适体，佩戴不移位； b) 内表面不应有长度大于2mm的突出物及尖锐物体； c）应厚度均匀并覆盖试验区。 5.1.4　舒适衬垫、防风围脖 舒适衬垫和防风围脖应符合以下技术要求： a) 舒适衬垫和防风围脖使用的纺织品甲醛含量、可分解致癌芳香胺染料应符合GB 18401 中B类的规定； b) 舒适衬垫和防风围脖使用的皮革和毛皮游离甲醛、可分解有害芳香胺染料应符合GB 20400 中B类的规定； c) 不应有刺鼻的异味。 5.1.5　佩戴装置 佩戴装置的部件应永久与佩戴装置或头盔连接，并符合以下技术要求： a）如果佩戴装置包括下颌系带，该系带宽度应≥20mm； b）如果佩戴装置有双 D 环、滑动棍等系紧装置，在佩戴装置调节时，为防止系带松脱应保留其足够的调节余量； c) 佩戴扣等快卸装置，打开方法应简单易行，同时必须防止可能产生的误操作，打开机构所用的推杆、按钮或其他部件应是红色或橙色的，只有在有意识操作时才能被打开，如果佩戴装置被设计成通过在某些部件上施加压力打开，那么当以100N±5N的力施加于该部件运动直线方向上时，佩戴扣不应被打开。 5.1.6　护目镜 护目镜应符合GB 811-2010 4.1.6 b）、c）的规定。 5.1.7　保护区及试验区 全盔、3/4盔的保护区及试验区应符合GB 811-2010 4.2.1 A类的规定；半盔的保护区及试验区应符合GB 811-2010 4.2.1 B类的规定。揭面盔的保护区及试验区应符合全盔的规定；组合盔每种状态的保护区及试验区均应符合对应形状的规定。 5.2　质量（含附件） 电动自行车头盔质量全盔、3/4盔应不大于1.6kg，半盔应不大于1.0kg。 5.3　视野 左、右水平视野不小于105°，上视野不小于7°，下视野不小于45°。 5.4　护目镜 按照6.5.1规定的方法进行测试，如果护目镜破碎，不得出现小于60°的碎片。 按照6.5.2规定的方法进行测试，护目镜的可见光透过率不小于85%。 5.5　侧向刚度性能 按照6.6规定的方法进行测试，应符合以下技术要求： a)最大变形不超过40mm； b)残余变形不超过15mm； c)壳体不得有碎片脱落（易脱落部件除外）。 5.6　固定装置稳定性 按照6.7规定的方法进行测试，应符合以下技术要求： a)电动自行车乘员头盔应不从头型上脱落； b)不得有系带撕裂撕断、连接件脱落及搭扣松脱现象。 5.7　佩戴装置强度 按照6.8规定的方法进行测试，应符合以下技术要求： a)在施加负载的情况下，不使用任何工具，30s内应能打开搭扣； b)系带伸长量不得超过25mm； c)不得有系带撕裂撕断、连接件脱落及搭扣松脱现象； d) 壳体不得有碎片脱落（易脱落部件除外）。 5.8　吸收碰撞能量性能 按照6.9规定的方法进行测试，应符合以下技术要求： a）加速度峰值不超过400g； b）加速度超过200g的作用时间应小于2ms； c）加速度超过150g的作用时间应小于4ms； d）壳体不得有碎片脱落（易脱落部件除外）；壳体裂口宽度不得超过2mm，长度不超过60mm。 5.9　耐穿透性能 按照6.10规定的方法进行测试，钢锥不得穿透电动自行车乘员头盔与头型产生接触；壳体不得有碎片脱落（易脱落部件除外）；壳体裂缝宽度不得超过2mm，长度不超过以试验点为中心半径30mm的范围。

General technical requirements and test method of Helmets for electric bicycle

T/SZAF 001-2020 中小学校和幼儿园智能体温筛查工程技术规范

中小学校和幼儿园体温筛查工程的建设，除参照本规范外，还应符合国家现行相关工程建设强制性标准及有关技术标准、规范的规定。智能体温筛查系统中使用的产品和设备应符合国家法律和现行相关技术标准，并经法定机构检验、认证合格。

Technical code for engineering of intelligent temperature screening for kindergartens, primary and secondary schools

DB43/T 1787-2020 区域安全风险评估工作指南

Guidelines for Regional Security Risk Assessment

DB43/T 1783-2020 煤矿安全生产标准化安全风险分级管控实施细则

Coal mine safety production standardization safety risk classification management and control implementation rules

DB43/T 1779-2020 生产安全事故应急避难场所分级管理规范

Standards for hierarchical management of emergency shelters for production safety accidents

DB43/T 1784-2020 化工园区整体性安全风险评价导则

Guidelines for Overall Safety Risk Assessment of Chemical Industry Parks

DB43/T 1789-2020 化工企业生产安全事故隐患排查治理体系细则

Detailed rules for the investigation and management system of hidden dangers of production safety accidents in chemical enterprises

T/LYFIA 017-2020 学校及托幼机构新冠肺炎疫情防控技术指南

1、本标准规定了学校新冠肺炎疫情防控的术语和定义、基本要求、防控措施、疫情处置、个人防护、校园管理、食品及饮水卫生、环境管理、消毒管理。本标准适用于幼儿园、普通中小学、中等职业学校、普通高等院校的新冠肺炎疫情防控工作，社会培训机构可参照执行。 2、术语和定义、基本要求、防控措施、疫情处置、个人防护、校园管理、食品及饮用水卫生、环境管理、消毒管理、

Technical guidelines for novel coronavirus pneumonia prevention and control in schools and kinderg

DB52/T 1492-2020 学校新型冠状病毒肺炎防控技术指南

Technical Guidelines for Prevention and Control of Novel Coronavirus Pneumonia in Schools

ASTM F2821-15(2020) 篮式拯救发动机的标准试验方法

1.1 These test methods enable the user to determine if a rescue litter meets the requirement for strength depending upon particular applications and methods of use. 1.2 The test methods described in this standard are designed to test several parameters under “manner of use” conditions. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Basket Type Rescue Litters

ASTM F1422-08(2020) 管理搜索和救援操作中使用事件命令系统框架的标准指南

1.1 This guide covers the use of the Incident Command System (ICS), as developed in the National Incident Management System (NIMS) in 2004, as the management framework for search and rescue (SAR) operations. 1.2 Except as otherwise specified herein, the methods and requirements of this standard also include NIMS, ICS, and National Response Framework (NRF) requirements, when required, for search and rescue personnel that deploy within the United States of America. 1.3 The ICS may be used outside of the United States for managing SAR operations, users of this standard need to be aware of other incident management requirements, guidelines, policies, procedures, and protocols within the area of ICS SAR operations. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Using the Incident Command System Framework in Managing Search and Rescue Operations

ASTM F1729-96(2020) 单人冷水生存/救援技术标准实践:帮助职位

1.1 This practice covers the recommended water rescue procedure for performing the heat escape lessening posture (HELP) position. 1.2 This practice is one in a set of self-rescue techniques for the water rescuer. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Single Person Cold Water Survival/Rescue Technique: HELP Position

ASTM F1767-14(2020) 搜索和救援用表格标准指南

1.1 This guide gives examples of forms used in the SAR community. 1.2 It is not the intent of this guide to recommend one form over another, but to make the user aware of the many different types of forms used. This guide does not purport to contain every form used in SAR, only a few examples of forms in each category. 1.3 These forms cover a great variety of the many aspects involved in SAR. This guide will attempt to give a few versions of forms used for each aspect identified. The user may choose which form best fits his particular need. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Forms Used for Search and Rescue

ASTM F1879-14(2020) 在搜索和救援犬中表现顺从和敏捷的标准指南

1.1 This guide establishes the minimum obedience and agility expected of canines that are part of a search dog team or crew. 1.2 Further training is required for a canine before it may perform as a member of a search dog team or crew. 1.3 This guide applies to canine members of all search resources classified in ASTM F1848 Standard Classification System for Canine Search Resources. 1.3.1 The advanced obedience and agility skills required for canine members of Kind D (Disaster/Collapsed Structure Search) dog teams or crews are not defined in this guide. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Demonstrating Obedience and Agility in Search and Rescue Dogs

ASTM F2794-09(2020) 一级（基本）车载搜索救援（MSAR）应答器的标准指南

1.1 This guide establishes the minimum knowledge, skills, and abilities (KSA) required for an MSAR responder and their equine during the deployment involving lost or missing persons and related non-technical rescue skills used to stabilize or minimize a missing person (subject) from remaining in peril. 1.2 MSAR users of the guide shall meet or hold the certified equivalent KSA defined in Guide F2209. 1.3 Users of this standard should, at minimum, have preexisting basic horsemanship skills that are equivalent to what is published within: The United States Pony Club Manual of Horsemanship: Basics for Beginners/D Level (1).2 1.4 Users of this standard should be aware of other MSAR standards, requirements, guidelines, policies, procedures, or protocols, or combinations thereof that have been established and which may be under the jurisdiction of federal, state, tribal, local, or other regional authorities (for examples of two (USA) state level MSAR standards, see Refs 2 and 3). 1.5 This standard is created without bias to the type of tack, gear, packs, first aid supplies, personal protective equipment (for self or equine), or riding discipline that is practiced by the MSAR responder. 1.6 This standard does not address the mounted evacuation of a subject, although an AHJ may determine when and if a mounted evacuation would be appropriate and what local protocols will be implemented. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Level 1 (Basic) Mounted Search and Rescue (MSAR) Responder

ASTM F1846-98(2020) 用于土地搜索地图的符号和标记的标准做法

1.1 This practice covers the symbols and markings to be used with land search maps to show resources, search coverage, status, and results. 1.2 Operational usage of these symbols and markings, the resources they represent, and maps are not included in this practice. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Symbols and Markings for Use With Land Search Maps

ASTM F1728-96(2020) 多人冷水生存/救援技术的标准做法:混合位置

1.1 This practice covers the recommended water rescue procedure for performing the huddle position. 1.2 This practice is one in a set of self-rescue techniques for the water rescuer. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Multiple Persons Cold Water Survival/Rescue Technique: Huddle Position

T/QDAS 034-2020 中小学生应急安全体验培训规范

本标准规定了中小学生应急安全体验培训的基本要求、场馆功能设置及配套设施、课程设置及内容、服务规范、安全管理、档案管理、课程考核要求、课程考核要点及对象、服务监督。 本标准适用于提供中小学生应急安全体验培训服务工作。

Specifications of emergency safety experience training for primary and secondary school students

T/NJAF 001-2020 人员密集区域体温快速筛查 红外热成像法

本标准共六章，主要内容为范围、规范性引用文件、术语和定义、实现方式、操作要求、统计与归档、附录A （资料性附录）红外热成像体温筛查设备检查记录表　、附录B （资料性附录）体温筛查记录表、参考文献

Infrared thermal imaging method for rapid screening of body temperature in crowded areas