13.220.40 材料和制品的可燃性和燃烧性能 标准查询与下载

GSO IEC 60754-2:2017 电缆材料燃烧过程中产生的气体测试 第2部分：酸度（通过 pH 测量）和电导率的测定

This part of IEC 60754 specifies the apparatus and procedure for the determination of the potential corrosivity of gases evolved during the combustion of materials taken from electric or optical fibre cable constructions by measuring the acidity (pH) and conductivity of an aqueous solution resulting from the gases evolved during the combustion. The general method specified in this standard is intended for the testing of individual components used in a cable construction. Formulae are given for the calculation of a weighted value for a combination of materials found in a specified cable. The use of this method will enable the verification of relevant requirements for either individual components or combined components of a cable construction stated in the appropriate cable specification. A simplified method is included for the testing of individual components where it is required only to demonstrate compliance with a stated performance requirement for quality control purposes. NOTE 1 The relevant cable standard should indicate which components of the cable should be tested, and which method of calculation (see Clause 8) should be used in the case of dispute. NOTE 2 This test method may be used to test materials to be used in cable manufacture, but a declaration of cable performance should not be made based on such a test. NOTE 3 For the purposes of this standard, the term “electric cable” covers all insulated metallic conductor cables used for the conveyance of energy or signals.

Test on gases evolved during combustion of materials from cables - Part 2: Determination of acidity (by pH measurement) and conductivity

GSO IEC 60331-21:2017 着火条件下的电缆试验 电路完整性 第21部分：程序和要求 额定电压高达 0,6/1,0 kV 的电缆

This part of IEC 60331 specifies the test procedure and gives the performance requirement, including a recommended flame application time, for cables of rated voltage up to and including 0,6/1,0 kV required to maintain circuit integrity when subjected to fire under specified conditions. It describes the means of sample preparation, continuity checking arrangements, electrical testing procedure, method of burning the cables and gives requirements for evaluating test results. It is intended to cover low voltage power cables, and control cables with a rated voltage.

Tests for electric cables under fire conditions - Circuit integrity - Part 21: Procedures and requirements - Cables of rated voltage up to and including 0,6/1,0 kV

GSO IEC 60695-1-12:2017 火灾危险测试 第1-12部分：电工产品火灾危险评估指南 消防安全工程

This part of IEC 60695 is intended as a general guideline for IEC Product Committees and provides: • an explanation of the principles and uses of fire safety engineering; • guidance on the use of fire safety engineering in the design of electrotechnical products; • fire safety engineering terminology, and concepts; • an indication of properties, data and tests needed for input into fire safety engineering assessments; • informative references. This international standard is not intended to be a detailed technical design guide, but is intended to provide guidance for product committees on fire safety engineering methods and performance based test information needs for use in performance based designs and fire hazard assessments of electrotechnical materials, assemblies, products and systems. More detailed information on fire safety engineering is contained in the ISO/TR 13387 series of documents (see Clause 2 and [1] to [6]) and in ISO 23932. NOTE Further detailed aspects of FSE are covered in ISO 16730 [7], ISO/TS 16732 [8], ISO/TS 16733, ISO 16734 [9], ISO 16735 [10], ISO 16736 [11], ISO 16737 [12] and ISO/TR 16738. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Fire hazard testing - Part 1-12: Guidance for assessing the fire hazard of electrotechnical products - Fire safety engineering

GSO IEC 60754-1:2017 电缆材料燃烧过程中产生的气体试验 第1部分：卤酸气体含量的测定

This part of IEC 60754 specifies the apparatus and procedure for the determination of the amount of halogen acid gas, other than hydrofluoric acid, evolved during the combustion of compounds based on halogenated polymers and compounds containing halogenated additives taken from electric or optical fibre cable constructions. NOTE 1 This test method is not able to determine hydrofluoric acid. A suitable method may be found in IEC 60684-2. NOTE 2 This test method may be used to test materials to be used in cable manufacture, but a declaration of cable performance should not be made based on such a test. NOTE 3 The relevant cable standard should indicate which components of the cable should be tested. NOTE 4 For the purposes of this standard, the term “electric cable” covers all insulated metallic conductor cables used for the conveyance of energy or signals. The method specified in this standard is intended for the testing of individual components used in a cable construction. The use of this method will enable the verification of requirements which are stated in the appropriate cable specification for individual components of a cable construction. NOTE 5 By agreement between the producer and purchaser, the methodology given in this standard may be used to test combinations of materials representing a cable construction, but a declaration of cable performance to this standard should not be made based on such a test. Information on such a method is given in Annex A. For reasons of precision this method is not recommended for reporting values of halogen acid evolved less than 5 mg/g of the sample taken.

Test on gases evolved during combustion of materials from cables - Part 1: Determination of the halogen acid gas content

EN 60695-11-2:2017 火灾危险测试 第 11-2 部分：测试火焰 1 kW 标称预混合火焰 Apparatus 确认测试安排和指南

Fire hazard testing - Part 11-2: Test flames - 1 kW nominal pre-mixed flame - Apparatus@ confirmatory test arrangement and guidance

ASTM E3048-17 使用中等尺度量热计（ICAL）辐射面板确定烧穿时间的标准测试方法

Standard Test Method for Determination of Time to Burn-Through Using the Intermediate Scale Calorimeter (ICAL) Radiant Panel

CAN/ULC-S137:2017(R2022) 床垫火势增长测试的标准方法（明火测试）

This new edition includes an Update to Referenced Standards and relocated within the normative section of the standard. The purpose of this test method is to investigate the ability of mattresses to resist rapid heat release by measuring specific fire test responses when the mattress or mattress set is subjected to a specified flaming ignition source under well ventilated conditions. This test method is applicable only to the finished mattresses and mattress sets and does not apply to testing of individual component materials used, such as ticking and upholstery materials, foams, cotton battings, etc. This test method does not provide information on the performance of a mattress or mattress set in other fire conditions or the contribution of the mattress to a developing fire condition.

Standard Method of Test for Fire Growth of Mattresses (Open Flame Test)

ASTM E2965-17 使用氧消耗量热计测定材料和产品的低释放率的标准测试方法

1.1 This fire-test-response standard provides a procedure for measuring the response of materials that emit low levels of heat release when exposed to controlled levels of radiant heating with or without an external igniter. 1.2 This test method differs from Test Method E1354 in that it prescribes a different specific test specimen size, specimen holder, test specimen orientation, a direct connection between the plenum and the top plate of the cone heater assembly to ensure complete collection of all the combustion gases (Fig. 1), and a lower volumetric flow rate for analyses via oxygen consumption calorimetry. It is intended for use on materials and products that contain only small amounts of combustible ingredients or components, such as test specimens that yield a peak heat release of

Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter

ASTM E662-17a 由固体材料产生的烟雾的特定光密度的标准测试方法

1.1 This fire-test-response standard covers determination of the specific optical density of smoke generated by solid materials and assemblies mounted in the vertical position in thicknesses up to and including 1 in. (25.4 mm). 1.2 Measurement is made of the attenuation of a light beam by smoke (suspended solid or liquid particles) accumulating within a closed chamber due to nonflaming pyrolytic decomposition and flaming combustion. 1.3 Results are expressed in terms of specific optical density which is derived from a geometrical factor and the measured optical density, a measurement characteristic of the concentration of smoke. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials

ASTM E3082-17e1 测定天然圣诞树防火处理效果的标准试验方法

Standard Test Methods for Determining the Effectiveness of Fire Retardant Treatments for Natural Christmas Trees

ASTM E2573-17 样品制备和现场制造的拉伸系统的安装的标准实践以评估表面燃烧特性

1.1 This practice describes procedures for specimen preparation and mounting when testing a site-fabricated stretch system to assess flame spread and smoke developed as surfaceburning characteristics using Test Method E84. 1.2 Testing is conducted with Test Method E84. 1.3 This practice does not provide pass/fail criteria that can be used as a regulatory tool. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. See IEEE/ASTM SI-10 for further details. 1.5 This fire standard cannot be used to provide quantitative measures. 1.6 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. Fire testing involves hazardous materials, operations, and equipment. This standard gives instructions on specimen preparation and mounting, but the fire-test-response method is given in Test Method E84. See also Section 10. 1.7 This practice shall not apply to vinyl stretch ceiling materials, which are covered by Practice E2599. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.9 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes shall not be considered requirements of the standard. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Specimen Preparation and Mounting of Site-Fabricated Stretch Systems to Assess Surface Burning Characteristics

ASTM E2574/E2574M-17 校车座椅总成防火试验标准试验方法

1.1 This is a fire-test-response standard. 1.2 This test method assesses the burning behavior of upholstered seating used in school buses by measuring specific fire-test responses when a school bus seat specimen is subjected to a specified flaming ignition source under normally ventilated conditions. 1.3 The ignition source is a gas burner. 1.4 This fire test is primarily useful to distinguish products that, when exposed to an ignition source, will become fully involved in fire from other products that will not. 1.5 Data are obtained describing the burning behavior of the seat assemblies from a specific ignition source until all burning has ceased. 1.6 This test method does not provide information on the fire performance of upholstered seating in fire conditions other than those conditions specified. 1.7 The burning behavior is visually documented by photographic or video recordings, whenever possible. 1.8 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.9 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions. 1.10 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.12 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Fire Testing of School Bus Seat Assemblies

ISO/TS 15791-2:2017 塑料 - 开发和使用塑料制品的中级火灾测试 - 第2部分:对半成品和成品使用中等尺寸试验

Plastics — Development and use of intermediate-scale fire tests for plastics products — Part 2: Use of intermediate-scale tests for semi-finished and finished products

IEC 60695-11-2:2017 火灾危险试验.第11-2部分:试验火焰.1kW预混合火焰.装置 确认性试验安排和指南

Fire hazard testing - Part 11-2: Test flames - 1 kW pre-mixed flame - Apparatus, confirmatory test arrangement and guidance

IEC 60695-11-2:2017 RLV 火灾危险试验.第11-2部分:试验火焰.1kW预混合火焰.装置 确认性试验安排和指南

Fire hazard testing - Part 11-2: Test flames - 1 kW pre-mixed flame - Apparatus, confirmatory test arrangement and guidance

EN ISO 5659-2:2017 塑料.烟熏剂-第2部分:测定光密度一院制的测试

Plastics - Smoke generation - Part 2: Determination of optical density by a single-chamber test

EN ISO 4589-1:2017 塑料.用氧指数测定其燃烧性能.第1部分:总则

Plastics - Determination of burning behaviour by oxygen index - Part 1: General requirements

EN ISO 4589-2:2017 塑料 通过氧指数测定其燃烧性 第2部分:室温试验

Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test

EN ISO 4589-3:2017 塑料.燃烧行为的氧指数测定.第3部分:高温试验

Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated-temperature test

ASTM D3675-17 使用辐射热能源的柔性细胞材料的表面可燃性的标准测试方法

1.1 This is a fire test response standard. 1.2 This test method describes the measurement of surface flammability of flexible cellular materials. 1.3 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not, by itself, incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.6 Specific information about hazards is given in Section 7. NOTE 1—There is no known ISO equivalent to this standard. 1.7 The values stated in SI units are to be regarded as the standard. The values stated in inch-pound units, in parentheses, are for information only and are approximations (see also IEEE/ASTM SI-10). 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source