13.220.40 材料和制品的可燃性和燃烧性能 标准查询与下载

CNS 14705-2007 建筑材料燃烧热释放率试验法－圆锥量热仪法

本标准规定建筑物室内装修材料在其火灾初期之耐燃性试验方法。

Method of test for heat release rate for building materials - Cone calorimeter method

NF X70-100-1:2006 火灾行为测试 气体流出物分析 第1部分：热降解产生的气体的分析方法

This section of the NF X 70-100 standard describes the physico-chemical analysis of the gases likely to be produced dudng the thermal degradation of substances, materials or combinations thereof. This thermal degradation can be achieved either as stipulated in part 2 of this document or following other thermal degradation methods. The analysis steps cover the gases most commonly found in fire contexts. These gases are listed below: -- carbon monoxide, CO; -- carbon dioxide, C02; -- halogen acids (hydrochloric acid, HCI; hydrobromic acid, HBr; hydrofluoric acid, HF); -- hydrocyanic acid, HCN; -- sulphur dioxide, S02; -- nitrogen monoxide, NO; nitrogen dioxide, NO2, and NO2 nitric oxides; -- aldehydes (acrolein, CH2CHCHO; formaldehyde, HCHO). The use of the results is under the responsibility of the sponsor of the tests. NOTE Since certain analytical methods carry health and safety risks, it is extremely important to take all necessary precautions to eliminate any dangers faced by operators during handling.

Fire behavior tests - Analysis of gaseous effluents - Part 1: methods of analysis of gases originating from thermal degradation

ASTM F1959/F1959M-05 测定服装材料电弧热性能值的标准试验方法

1.1 This test method is used to measure the arc rating of materials intended for use as flame resistant clothing for workers exposed to electric arcs that would generate heat flux rates from 84 to 25120 kW/m 2 [2 to 600 cal/cm2].1.2 This test method will measure the arc rating of materials which meet the following requirements: less than 150 mm [6 in.] char length and less than 2 s afterflame when tested in accordance with Test Method D 6413.1.2.1 It is not the intent of this test method to evaluate non flame-resistant materials except where used as under layers in multiple-layer specimens.1.3 The materials used in this test method are in the form of flat specimens.1.4 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions.1.5 The values stated in SI units shall be regarded as standard except as noted. Within the text, alternate units are shown in brackets. The values stated in each system may not be exact equivalents therefore alternate systems must be used independently of the other. Combining values from the systems described in the text may result in nonconformance with the method.1.6 This test method does not apply to electrical contact or electrical shock hazards.1.7 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. For specific precautions, see Section .

Standard Test Method for Determining the Arc Thermal Performance Value of Materials for Clothing

ASTM E2405-05 使用垂直定向样本的中型试验测定材料的耐火和耐热参数的标准试验方法

This test method is used primarily to determine time-to-ignition, vertical flame spread rate, and lateral flame spread rate of materials, products and assemblies in a vertical orientation when exposed to a graduated radiant heat flux. Optionally, this test method is suitable to measure the heat release rate and smoke development rate of materials, products and assemblies in a vertical orientation when exposed to a graduated radiant heat flux. This test method is suitable to test materials that have a planar or nearly planar exposed surface. This test method is not intended to test materials with surface cracks, fissures or holes exceeding 8 mm in width or 10 mm in depth. Also, the total area of such cracks, fissures or holes at the surface shall not exceed 30 % of the exposed surface area of the specimen.1.1 This fire-test-response standard determines fire properties related to piloted ignition of a vertically oriented specimen exposed to an external graduated radiant heat flux as shown in . This test method provides data suitable for comparing the performance of materials, which are used as the exposed surfaces of walls or other vertically orientated products in construction applications.Note 1This test method has been prepared to closely follow the test procedure of ISO 5658-4, however with additional provisions for heat release and smoke development measurements that are optional.1.2 The fire characteristics determined by this test method include time-to-ignition, vertical flame spread rate and lateral flame spread rate. Optional measurements include heat release rates and visible smoke development rates.1.3 The optional heat release rate is determined by the principle of oxygen consumption calorimetry, via measurement of the oxygen consumption as determined by the oxygen concentration and flow rate in the exhaust product stream (exhaust duct).1.4 The values stated in SI units are to be regarded as the standard.1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.1.6 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazard is given in Section .This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Fire and Thermal Parameters of Materials Using an Intermediate Scale Test with Vertically Oriented Specimen

ASTM F1959/F1959M-04 测定服装材料电弧热性能值的标准试验方法

1.1 This test method is used to measure the arc rating of materials intended for use as flame resistant clothing for workers exposed to electric arcs that would generate heat flux rates from 84 to 25120 kW/m 2 [2 to 600 cal/cm2].1.2 This test method will measure the arc rating of materials which meet the following requirements: less than 150 mm [6 in.] char length and less than 2 s afterflame when tested in accordance with Test Method D 6413.1.2.1 It is not the intent of this test method to evaluate non flame-resistant materials except where used as under layers in multiple-layer specimens.1.3 The materials used in this test method are in the form of flat specimens.1.4 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions.1.5 The values stated in SI units shall be regarded as standard except as noted. Within the text, alternate units are shown in brackets. The values stated in each system may not be exact equivalents therefore alternate systems must be used independently of the other. Combining values from the systems described in the text may result in nonconformance with the method.1.6 This test method does not apply to electrical contact or electrical shock hazards.1.7 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. For specific precautions, see Section .

Standard Test Method for Determining the Arc Thermal Performance Value of Materials for Clothing

KS C IEC 60695-2-20:2004 火灾危险试验.第2部分:灼烧/发热导线基础试验方法.20节:热线卷点火试验

이 규격은 1995년에 제1판으로 발행된 IEC 60695-2-20 Fire haza

Fire hazard testing-Part 2-20:Glowing/hot-wire based test methods-Hot-wire coil ignitability test on materials

KS C IEC 60695-2-20-2004(2019) 着火危险试验第2－20部分:灼热/热丝基试验方法材料的热丝线圈可燃性试验

Fire hazard testing－Part 2－20：Glowing/hot-wire based test methods－Hot-wire coil ignitability test on materials

KS C IEC 60695-2-13:2004 火灾危险试验.第2-13部分:灼热金属线/热线的试验方法.材料的灼热金属线火灾性试验方法

이 규격은 글로 와이어 발화 온도(GWIT:glow-wire ignition tempe

Fire hazard testing－Part 2－13：Glowing/hot-wire based test methods－Glow-wire ignitability test method for materials

LST EN 60695-11-2-2004 火灾隐患测试 第 11-2 部分：测试火焰 1 kW 标称预混火焰 设备、确认测试安排和指南（IEC 60695-11-2:2003）

Fire hazard testing. Part 11-2: Test flames. 1 kW nominal pre-mixed flame. Apparatus, confirmatory test arrangement and guidance (IEC 60695-11-2:2003)

GA/T 505-2004 材料的火灾场景烟气制取方法

本标准规定了材料连续产生模拟火灾场景毒性烟气的制取方法和装置。 本标准适用于材料产烟毒性危险评价及相关毒物成分分析。 本标准不适用于实际火灾场景烟气流温度模拟和实际火灾场景演变过程模拟。

Method of preparing the fire scenario effluents from a material

XF/T 505-2004 材料的火灾场景烟气制取方法

Material fire scene smoke production method

XF 495-2004 阻燃铺地材料性能要求和试验方法

Performance requirements and test methods for flame retardant floor covering materials

GA 495-2004 阻燃辅地材料性能要求和试验方法

本标准规定了阻燃铺地材料的定义、分类、技术要求、试验方法、检验规则及标签、包装、贮存等内容。 本标准适用于木质地板(浸溃纸层压饰面木质地板、实木复合地板)、机制地毯、塑胶地板等铺地材料。

Specification of flame-retardant floor-covering

ASTM E1474-04e1 标准测试方法 用于确定软垫家具和床垫组件或​​复合材料的热释放率 使用台秤氧气消耗量热仪

Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter

KS M ISO 15029-1-2003(2018) 耐火流体 - 第1部分喷射燃烧特性的石油和相关产品的测定:喷火焰持久性空心锥形喷嘴法

Petroleum and related products - Determination of spray ignition characteristics of refractory fluids - Part 1: Spray flame persistence - Hollow-conical nozzle method

KS M ISO 15029-1:2003 石油和相关产品.耐火液体喷射点燃特性的测定.第1部分:喷射火焰持久性.空心喷射器法

이 규격은 내화성 유체의 가압 분무의 범위 이내에 서 여러 지점에 적용한 불꽃의 지속성 평

Petroleum and related products-Determination of spray ignition characteristics of fire-resistant fluids-Part 1: Spray flame persistence-Hollow-cone nozzle method

KS M ISO 15029-1-2003(2023) 石油及相关产品-耐火性流体的喷雾点火特性测定-第一部分:喷雾火花持续性-速宾-锥形喷嘴法

Petroleum and related products - Determination of spray ignition characteristics of refractory fluids - Part 1: Spray flame persistence - Hollow-conical nozzle method

ISO 9772:2001/Amd 1:2003 泡沫塑料.小火焰下小试样水平燃烧特性的测定.修改件1:试样

Cellular plastics — Determination of horizontal burning characteristics of small specimens subjected to a small flame — Amendment 1: Specimens

CNS 6532-2003 建筑物室内装修材料之耐燃性试验法

本标准规定建筑物室内装修材料在其火灾初期之耐燃性试验方法。各级之试验方法如表1所示，配合其耐燃性级别作基材试验、表面试验及附加试验

Method of test for incombustibility of interior finish material of buildings

ASTM E2058-03 用火焰传播装置（FPA）测量合成聚合物材料可燃性的标准试验方法

1.1 This fire-test-response standard determines and quantifies synthetic polymer material flammability characteristics, related to the propensity of materials to support fire propagation, by means of a fire propagation apparatus (FPA). Material flammability characteristics that are quantified include time to ignition (tign), chemical ( Qchem), and convective ( Qc) heat release rates, mass loss rate ( m) and effective heat of combustion (EHC).1.2 The following test methods, capable of being performed separately and independently, are included herein:1.2.1 Ignition Test, to determine tign for a horizontal specimen;1.2.2 Combustion Test, to determine Qchem, Qc'm, and EHC from burning of a horizontal specimen; and,1.2.3 Fire Propagation Test to determine Qchem from burning of a vertical specimen.1.3 Distinguishing features of the FPA include tungsten-quartz external, isolated heaters to provide a radiant flux of up to 65 kW/m 2 to the test specimen, which remains constant whether the surface regresses or expands; provision for combustion or upward fire propagation in prescribed flows of normal air, air enriched with up to 40 % oxygen, air oxygen vitiated, pure nitrogen or mixtures of gaseous suppression agents with the preceding air mixtures; and, the capability of measuring heat release rates and exhaust product flows generated during upward fire propagation on a vertical test specimen 0.305 m high.1.4 The FPA is used to evaluate the flammability of synthetic polymer materials and products. It is also designed to obtain the transient response of such materials and products to prescribed heat fluxes in specified inert or oxidizing environments and to obtain laboratory measurements of generation rates of fire products (CO2, CO, and, if desired, gaseous hydrocarbons) for use in fire safety engineering.1.5 Ignition of the specimen is by means of a pilot flame at a prescribed location with respect to the specimen surface.1.6 The Fire Propagation test of vertical specimens is not suitable for materials that, on heating, melt sufficiently to form a liquid pool.1.7 Values stated are in SI units. Values in parentheses are for information only.1.8 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.

Standard Test Methods for Measurement of Synthetic Polymer Material Flammability Using a Fire Propagation Apparatus (FPA)