13.340.10 防护服装 标准查询与下载
共找到 1697 条与 防护服装 相关的标准，共 114 页
1.1 This test method establishes a small-scale laboratory screening procedure for comparing the ignition resistance and burning characteristics of materials used in protective clothing where flame resistance is not the primary form of protection provided by the clothing. 1.1.1 This test method shall not be used in applications where flame resistance is the primary form of protection offered by the protective clothing. Other flammability test methods are more appropriate for those materials. 1.1.2 This test method provides a means for comparing ease of ignition and burning behavior of materials which include plastic or elastomeric films, coated fabrics, flexible laminates, multilayer material systems, or other protective clothing materials that are not designated for offering flame resistance as their primary form of protection. 1.2 This test method is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.3 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.4 The values stated in SI units or other units shall be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Effects of Flame Impingement on Materials Used in Protective Clothing Not Designated Primarily for Flame Resistance
- ICS
- 13.340.10
- CCS
- /
- 发布
- 2020
- 实施
- 0000-00-00
What is BS EN 510- Specification for protective clothing about? BS EN 510 discusses the specification for protective clothing. BS EN 510 is a European standard on the specification for protective clothing to prevent the risk of entanglement with moving parts. BS EN 510 specifies the design requirements of protective garments that minimize the risk of its entanglement or drawing-in by moving parts when the wearer is working at or near hazardous moving machines or devices, complementary to the general requirements as stated in EN ISO 13688 . BS EN 510 applies to specific garments to be worn when the risk of entanglement cannot be effectively controlled by physically safeguarding moving parts of machines. Note: BS EN 510 does not include protective clothing against injuries by special moving machine parts for which specific standards exist like protective clothing for a user of chainsaws (EN ISO 11393). Who is BS EN 510- Specification for protective clothing for ? BS EN 510 on...
Specification for protective clothing for use where there is a risk of entanglement with moving parts
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-31
- 实施
- 2019-12-31
Protective clothing against heat and flame — Part 2: Skin burn injury prediction — Calculation requirements and test cases
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-11
- 实施
Protective clothing against heat and flame — Part 2: Skin burn injury prediction — Calculation requirements and test cases
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-11
- 实施
Protective clothing against heat and flame — Part 1: Test method for complete garments — Measurement of transferred energy using an instrumented manikin
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-11
- 实施
Protective clothing against heat and flame — Part 1: Test method for complete garments — Measurement of transferred energy using an instrumented manikin
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-11
- 实施
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 5:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-09
- 实施
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 6:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-09
- 实施
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 5:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-09
- 实施
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 6:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-12-09
- 实施
1 Scope This document provides a test method for evaluating the physiological impact of protective fabric ensembles and potentially protective clothing ensembles in a series of simulated activities (phases) under defined ambient conditions. This standard test method characterizes the essential properties of fabric assemblies of a representative garment or clothing ensemble for thermo-physiological assessment: — dry thermal insulation; — cooling properties during average metabolic activity and moisture management (dry and wet heat transfer); — drying behaviour. Default measurements are done on fabric samples representing the garment or protective clothing combination. Optionally and in addition to the standard test method, the same testing protocol can be applied to characterise more complex protective clothing ensembles including underwear, air layer and certain design features 1 . In addition, measurements on readymade garments are possible. This test method is intended to be used to measure and describe the behaviour of fabric assemblies of a garment or clothing ensemble in response to a simulated series of activities under controlled laboratory conditions, with the results used to optimize garment combinations and material selection. Furthermore, this document together ISO 18640‑2, is intended to be used to describe the thermo-physiological impact of protective clothing but not the risk for heat stress unde...
Protective clothing for firefighters. Physiological impact - Measurement of coupled heat and moisture transfer with the sweating torso
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-30
- 实施
- 2019-11-30
1 Scope This document establishes minimum performance, classification, and marking requirements for protective clothing worn by operators handling pesticide products as well as re-entry workers . For the purpose of this document, the term pesticide applies to insecticides, herbicides, fungicides, and other substances applied in liquid form that are intended to prevent, destroy, repel, or reduce any pest or weeds in agricultural settings, green spaces, roadsides, etc. It does not include biocidal products used for agricultural and non-agricultural settings. Pesticide handling includes mixing and loading, application, and other activities such as cleaning contaminated equipment and containers. Concentrated pesticides are typically handled during mixing and loading. Protective clothing covered by this document includes, but is not limited to, shirts, jackets, trousers, coveralls, aprons, protective sleeves, caps/hats and other headwear (excluding hard hats made of rigid materials, e.g. hats worn by construction workers), and accessories used under knapsack/backpack sprayers. This document does not address items used for the protection of the respiratory tract, hands, and feet. This document does not address protection against fumigants .
Protective clothing. Performance requirements for protective clothing worn by operators applying pesticides and for re-entry workers
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-30
- 实施
- 2019-11-30
What is ISO 11393‑6- Body protectors for the users of hand-held chainsaws about? ISO 11393 discusses protective clothing for users of hand-held chainsaws. ISO 11393‑6 is an international standard on upper body protectors for users of hand-held chainsaws that ensure protection against the risks arising from the use of hand-held chainsaws. ISO 11393‑6 is the sixth part of the multi-series that specifies the performance requirements, test methods, design requirements, identification, and marking information for upper body protectors that offer protection against cutting by hand-held chainsaws. ISO 11393‑6 specifies two different designs of jackets Design A jackets protect at the shoulder and the arms. Design B jackets additionally protect the front of the torso. Who is ISO 11393‑6- Upper b ody protectors for the users of hand-held chainsaws for? ISO 11393‑6 on upper body protectors for the users of hand-held chainsaws is useful for: Manufacturers of body protectors Designers of body protectors Testers of body protectors Health and safet...
Protective clothing for users of hand-held chainsaws - Performance requirements and test methods for upper body protectors
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-30
- 实施
- 2019-11-30
What is ISO 21942- Minimum requirements for s tation uniforms for firefighters about? ISO 21942 discusses station uniforms for firefighters. ISO 21942 is an international standard that provides minimum requirements for station uniforms for firefighters to ensure prevention from fire hazards. ISO 21942 sets out minimum performance requirements for station uniforms for firefighters that are provided by agencies to be worn under primary protective garments compliant with the relevant standards. Garments developed by ISO 21942 complement the performance built into primary protection firefighting garments in terms of minimizing the impact on hindrance, metabolic heat, and comfort. ISO 21942 specifies two levels of requirements for station uniforms: Level 1 specifies minimum no melting nor dripping requirements that provide no additional protection but ensure the firefighter is not harmed by the melting of station uniform materials in cases where heat or flames impinge the station uniform. Level 2 specifies heat and flame requirements to provide minimum protection. It can be combined with additional layers or garments to meet the requirements of a standard for a specific primary protection garment, this combination should provide improved protection and comfort. Note: A station uniform, as defined by ISO 21942, is understood to not be a formal uniform or parade uniform, which is not likely to be worn under primary protective firefighting garments. Who is ISO 21942- Minimum requirements for s tation uniforms for firefighters for ? ISO 21942 on the minimum requirements ...
Station uniform for firefighters
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-30
- 实施
- 2019-11-30
1 Scope This document specifies a method for evaluating the thermo-physiological impact of protective fabric ensembles and potentially protective clothing ensembles in a simulated activity under defined relevant conditions for firefighters. This document is intended to be used to assess the thermo-physiological impact of protective fabric ensembles and potentially protective clothing ensembles but not the risk for heat stress due to actual fire conditions. The results of this test method can be used as elements of characterisation and comparison of thermo-physiological impact of various types of protective fabric ensembles and potentially protective clothing ensembles. Default measurements are undertaken on fabric samples representing the garment or protective clothing combination. Optionally and in addition to the standard test method, the same testing protocol can be applied to characterise protective clothing ensembles including underwear, air layers and certain design features 4 . In addition measurements on readymade garments are optionally possible. NOTE The presently used evaluation methods are only validated for structural firefighting garments.
Protective clothing for firefighters. Physiological impact - Determination of physiological heat load caused by protective clothing worn by firefighters
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-30
- 实施
- 2019-11-30
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 4:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-21
- 实施
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 1:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-21
- 实施
Guidance on the selection, use, care and maintenance of personal protective equipment(PPE) designed to provide protection for firefighters
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-21
- 实施
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 2:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-21
- 实施
PPE for firefighters — Test methods and requirements for PPE used by firefighters who are at risk of exposure to high levels of heat and/or flame while fighting fires occurring in structures — Part 2:
- ICS
- 13.340.10
- CCS
- 发布
- 2019-11-21
- 实施
