13.340.20 头部防护设备 标准查询与下载

ASTM F2727-09(2020) 标签产品标签制造商标准指南

1.1 This guide sets forth labeling and instruction guidelines for manufacturers of headgear for non-motorized sports and recreation. 1.2 This guide applies only to protective headgear whose standard specifications are under auspices of ASTM Committee F08. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Manufacturers for Labeling Headgear Products

ASTM F2530-13(2020) 用于公牛护栏的防护头盔标准规范

1.1 This specification covers performance requirements and describes test methods for protective headgear with faceguards for use in bull riding. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear with faceguard meets all of the requirements of the specification in their entirety. A headgear with faceguard that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be sold with any indication that it meets parts of the specification. 1 This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of Subcommittee F08.53 on Headgear and Helmets. Current edition approved April 1, 2020. Published April 2020. Originally approved in 2005. Last previous edition approved in 2013 as F2530 – 13. DOI: 10.1520/F2530-13R20. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1.4 Headgear with faceguards designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.5 The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Protective Headgear with Faceguard Used in Bull Riding

BS EN ISO 18526-1:2020 眼睛和面部保护 测试方法-几何光学特性

What is ISO 185261 about?    ISO 18526 discusses eye and face protection. ISO 185261 is the first part of the multi-series ISO 18526. ISO 185261 specifies the reference test methods for determining the spherical, cylindrical, and prismatic refractive power properties of unmounted and mounted Plano lenses (non-corrective lenses) for eye and face protectors .   Note: ISO 185261 does not apply to any eye and face protection product requirement standards for which other test methods are specified.  Who is ISO 185261  for?   ISO 185261 on eye and face protection test methods is useful for:   Manufacturers of eye and face protectors 

Eye and face protection. Test methods - Geometrical optical properties

BS EN ISO 18526-2:2020 眼睛和面部保护 测试方法-物理光学性能

What is ISO 18526-2 about?    ISO 18526 discusses eye and face protection. ISO 185262 is the second part of the multi-series ISO 18526. ISO 185262 specifies the reference test methods for determining the physical optical properties of personal eye and face protectors.   Note: ISO 185262 does not apply to any eye and face protection products for which the requirements standard(s) specifies other test methods.  Who is ISO 18526-2 for?  

Eye and face protection. Test methods - Physical optical properties

BS EN ISO 18526-4:2020 眼睛和面部保护 测试方法 头型

What is ISO 18526-4 about?    ISO 18526 discusses eye and face protection. ISO 18526-4 is the fourth part of the ISO 18526 multi-series that elaborates on test method using headforms. ISO 18526-4 specifies the dimensions and tolerances of the headforms used for the testing of eye and face protectors .   Additional information is given for anthropometric measurement methods, anthropometric data for head and face dimensions and human test panels.   Who is ISO 18526-4 for?   ISO 18526-4 on eye and face protection is useful for:   E...

Eye and face protection. Test methods - Headforms

EN ISO 18526-1:2020 眼和面保护 - 试验方法第1部分:几何光学性能

This document specifies the reference test methods for determining the spherical, cylindrical, and prismatic refractive power properties of unmounted and mounted plano lenses (non-corrective lenses) for eye and face protectors. This document does not apply to any eye and face protection product requirement standards for which other test methods are specified. Other test methods can be used provided they have been shown to be equivalent and include uncertainties of measurement no greater than those required by the reference method.

Eye and face protection - Test methods - Part 1: Geometrical optical properties (ISO 18526-1:2020)

T/C3D 01-2020 应急防疫用眼面部防护具

本标准提出在新冠病毒肺炎抗疫过程中应用的医疗场景和其它非医疗职业的场景下，对眼面部护具要求的功能分级和性能指标分级，并由此推荐在不同场景中眼面部护具的规范用法。 本标准按照新冠疫情社会不同场景的危险等级，把眼面部防护具分为以下5类使用环境，并要求在不同的环境中使用的防护具应该满足的防护性能指标。 I类环境：户外一般人员非相对密集区域； II类环境：户外人员相对密集公共区域（如街道社区、楼宇办公区、会议室、商场超市、景区密集场所、公交地铁、客运工具、汽车站、火车站、船运站、飞机场等），一般疫区人员来往居家观察区； III类环境：一般医院非传染病区环境，公共区域相对密闭狭窄环境（如电梯、出租车等），重点疫区来往和疑似确诊患者密切接触人员来往居家隔离区； IV类环境：医院传染病区（疑似和确诊患者）诊疗区域（如发热门诊室、候诊室、观察室及处置室、影像检查室、传染病房等），120急救车和应急疑似确诊患者和标本护送转运车辆； V类环境：重症监护室及手术治疗室、病毒采样标本检验实验室

Eye and Face Protectors for used in Emergency Epidemic Prevention

EN ISO 18526-2:2020 眼睛和脸部保护 - 试验方法第2部分:物理光学性能

This document specifies the reference test methods for determining the physical optical properties of personal eye and face protectors. This document does not apply to any eye and face protection products for which the requirements standard(s) specifies other test methods. Other test methods can be used provided they have been shown to be equivalent and include uncertainties of measurement no greater than those required of the reference method.

Eye and face protection - Test methods - Part 2 : Physical optical properties (ISO 18526-2:2020)

EN ISO 18526-4:2020 眼睛和脸部保护 - 试验方法第4部分:头部

This document specifies the dimensions and tolerances of the headforms used for the testing of eye and face protectors. Additional information is given for: — anthropometric measurement methods; — anthropometric data for head and face dimensions; — human test panels.

Eye and face protection - Test methods - Part 4: Headforms (ISO 18526-4:2020)

ISO 18526-1:2020 眼和面保护 - 试验方法第1部分:几何光学性能

This document specifies the reference test methods for determining the spherical, cylindrical, and prismatic refractive power properties of unmounted and mounted plano lenses (non-corrective lenses) for eye and face protectors. This document does not apply to any eye and face protection product requirement standards for which other test methods are specified. Other test methods can be used provided they have been shown to be equivalent and include uncertainties of measurement no greater than those required by the reference method.

Eye and face protection — Test methods — Part 1: Geometrical optical properties

BS EN ISO 18526-3:2020 眼睛和面部保护 测试方法-物理和机械性能

What is ISO 18526-3 about?    ISO 18526 discusses eye and face protection. ISO 18526-3 is the third part of the multi-series ISO 18526. ISO 185263 specifies the reference test methods for determining physical and mechanical properties of eye and face protectors.   Note: ISO 18526-3 does not apply to any eye and face protection products for which the requirements standard(s) specifies other test methods  Who is ISO 18526-3 for?   ISO 18526-3 on eye and face protection test methods is useful for:   Eyewear manufacturers  

Eye and face protection. Test methods - Physical and mechanical properties

ISO 18526-2:2020 眼睛和脸部保护 - 试验方法第2部分:物理光学性能

This document specifies the reference test methods for determining the physical optical properties of personal eye and face protectors. This document does not apply to any eye and face protection products for which the requirements standard(s) specifies other test methods. Other test methods can be used provided they have been shown to be equivalent and include uncertainties of measurement no greater than those required of the reference method.

Eye and face protection — Test methods — Part 2: Physical optical properties

ISO 18526-4:2020 眼睛和脸部保护 - 试验方法第4部分:头部

This document specifies the dimensions and tolerances of the headforms used for the testing of eye and face protectors. Additional information is given for: — anthropometric measurement methods; — anthropometric data for head and face dimensions; — human test panels.

Eye and face protection — Test methods — Part 4: Headforms

EN ISO 18526-3:2020 眼和面部防护试验方法第3部分:物理和机械性能

This document specifies the reference test methods for determining the physical and mechanical properties of eye and face protectors. This document does not apply to any eye and face protection products for which the requirements standard(s) specifies other test methods. Other test methods can be used if shown to be equivalent and include uncertainties of measurement no greater than those required of the reference method.

Eye and face protection - Test methods - Part 3: Physical and mechanical properties (ISO 18526-3:2020)

ISO 21924-9:2020 武术.武术用防护设备.第9部分:武术散打头部保护器的附加要求和试验方法

This document specifies the terms and definitions, product structure, classification, requirements and test methods of head protectors for Wushu Sanda. This document is applicable to Wushu Sanda head protectors sewn with polyurethane (PU) synthetic leather, polyvinyl chloride (PVC) artificial leather, foamed plastic products and other materials.

Martial arts — Protective equipment for martial arts — Part 9: Additional requirements and test methods for Wushu Sanda head protectors

ISO 18526-3:2020 眼和面部防护试验方法第3部分:物理和机械性能

This document specifies the reference test methods for determining the physical and mechanical properties of eye and face protectors. This document does not apply to any eye and face protection products for which the requirements standard(s) specifies other test methods. Other test methods can be used if shown to be equivalent and include uncertainties of measurement no greater than those required of the reference method.

Eye and face protection — Test methods — Part 3: Physical and mechanical properties

T/ZZB 1489-2019 多功能警用防暴头盔

本标准规定了多功能警用防暴头盔产品的术语和定义、分类和代号、基本要求、技术要求、试验方法、检验规则、包装、运输和贮存、质量承诺。 本标准适用于多功能警用防暴头盔（以下简称防暴头盔）。

Multi-function police anti-riot helmet

KS G 5816-2019 登山装备 - 登山者头盔 - 安全要求和测试方法

Mountaineering equipment — Helmets for mountaineers — Safety requirements and test methods

ASTM F1776-19 彩弹运动眼部防护装置标准规范

Standard Specification for Eye Protective Devices for Paintball Sports

19/30400755 DC BS EN 14458 AMD1 个人眼科设备 高性能面罩仅适用于防护头盔

BS EN 14458 AMD1. Personal eye-equipment. High performance visors intended only for use with protective helmets