13.340.20 头部防护设备 标准查询与下载

19/30380310 DC BS EN ISO 12609-1 用于化妆品和医疗应用的人类和动物的眼睛和面部防护 防止强光源的伤害 第 1 部分：产品规范

BS EN ISO 12609-1. Eye and face protection against intense light sources used on humans and animals for cosmetic and medical applications - Part 1. Specification for products

ASTM F803-19 所选运动眼保护器的标准规范

1.1 This specification covers eye protectors, designed for use by players of basketball, baseball, and soccer to minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by baseballs and softballs, basketballs, soccer balls, hands, elbows, and fingers. Protective eyewear offers protection only to the eyes and adnexa and does not protect other parts of the head. 1.2 Protectors are divided into three types depending on their design characteristics. 1.3 This specification applies to eye protectors for use by wearers of corrective lenses and also by those players who do not require prescription eyewear. (Warning—Polycarbonate or Trivex spectacle lenses should be used if spectacles are worn under protective eyewear.) 1.4 In this standard, the use of the words “shall” or “must” indicates a mandatory requirement. The word “should” indicates a recommendation. 1.5 Failure of the product occurs when the protector is unable to meet the general, mechanical, and optical (if applicable) requirements of the standard. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.7 The following precautionary caveat pertains only to the test methods portions, Sections 9 – 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Eye Protectors for Selected Sports

ASTM F3103-14(2019) 越野摩托车和ATV头盔测试标准规范

1.1 This specification covers performance requirements for helmets used by off-road motorcycle and All-Terrain Vehicle (ATV) riders. 1.2 Compliance with the federally mandated FMVSS No. 218 shall be documented as part of compliance with this ASTM standard. 1.3 This specification provides additional performance requirements including positional stability and performance criteria for chin bars on full-facial coverage helmets if the helmet is equipped with a chin bar. 1.4 This standard does not require that helmets provide full facial coverage. 1.5 This is a performance specification and is not intended to restrict design. 1.6 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.7 Partial utilization of this standard is prohibited. Any statement of compliance with this specification must be a certification that the product meets all of the requirements of this specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed this standard, and should not be sold with any indication that it meets parts of this standard. 1.8 Headgear designed to comply with this and other standards may proclaim uses as certified by the manufacturer. 1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.10 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Testing Off-Road Motorcycle and ATV Helmets

ISO/TR 22463:2019 激光或强光源（ILS）手术中使用的病人和病人眼睛保护器指南

Patient and client eye protectors for use during laser or intense light source (ILS) procedures — Guidance

ASTM F2879-19 软空气运动用眼睛保护装置的标准规范

Standard Specification for Eye Protective Devices for Airsoft Sports

BS ISO 4869-6:2019 声学 听力保护器 主动降噪耳罩声音衰减的测定

1   Scope This document is concerned with active noise reduction (ANR) earmuffs. It specifies the test methods for the determination of the active insertion loss and calculation procedures for deriving the total attenuation. For this aim, the values of sound attenuation in the passive mode also have to be known and are determined according to ISO 4869‑1. These methods are intended for steady noise exposures and are not applicable to noises containing impulsive components. The test methods account for the acoustical interaction between the wearer and the device using measurements of passive (REAT) and active microphone-in-real-ear (MIRE) measurements as specified in ISO 4869‑1 and ISO 11904‑1, respectively.

Acoustics. Hearing protectors - Determination of sound attenuation of active noise reduction earmuffs

ISO 4869-6:2019 声学 - 听力保护器 - 第6部分:确定有源降噪耳罩的声衰减

This document is concerned with active noise reduction (ANR) earmuffs. It specifies the test methods for the determination of the active insertion loss and calculation procedures for deriving the total attenuation. For this aim, the values of sound attenuation in the passive mode also have to be known and are determined according to ISO 4869-1. These methods are intended for steady noise exposures and are not applicable to noises containing impulsive components. The test methods account for the acoustical interaction between the wearer and the device using measurements of passive (REAT) and active microphone-in-real-ear (MIRE) measurements as specified

Acoustics — Hearing protectors — Part 6: Determination of sound attenuation of active noise reduction earmuffs

ASTM F3164-19 球拍运动(网球拍,壁球,网球)用护目镜的标准规范

1.1 This specification covers eye protectors, designed for use by players of racket sports (racquetball, squash, tennis), that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by racket-sport rackets and balls. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. 1.2 Protectors are divided into three types depending on their design characteristics. 1.3 This specification applies to eye protectors for use by wearers of corrective lenses and also by those players who do not require prescription eyewear. (Warning—Polycarbonate or Trivex spectacle lenses should be used if spectacles are worn under protective eyewear.) 1.4 In this standard, the use of the words “shall” or “must” indicates a mandatory requirement. The word “should” indicates a recommendation. 1.5 Failure of the product occurs when the protector is unable to meet the general, mechanical, and optical (if applicable) requirements of the standard. 1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.7 The following precautionary caveat pertains only to the test methods portions, Sections 9 – 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Eye Protectors for Racket Sports (Racquetball, Squash, Tennis)

BS ISO 18639-5:2018 消防员执行特定救援活动所需的个人防护装备 头盔

What is ISO 18639‑5- Helmet for firefighters undertaking specific rescue activities about? ISO 18639 discusses PPE ensembles for firefighters undertaking specific rescue activities. ISO 18639‑5 is an international standard on helmets for firefighters to ensure protection during specific rescue activities. . ISO 18639‑5 is the fifth part of a multi-part series that provides the principles that govern the development of incident type and/or hazard-specific test methods and minimum performance requirements for helmets for firefighters while engaged in specific rescue activities. ISO 18639‑5 covers general helmet design, the minimum performance level of the materials used and the methods of test for determining this performance level. Note1: ISO 18639‑5 does not cover special helme ts f or use in other high-risk situations such as firefighting. Note2: ISO 18639‑5 does not cover protection for the torso, arms, legs, and feet or protection of the hands against other hazards, e.g., chemical, biological, radiation, and electrical hazards, except for limited, accidental exposure to fire ground chemicals and contaminated blood or body fluids. Who is

PPE ensembles for firefighters undertaking specific rescue activities - Helmet

ISO 18639-5:2018 从事特定救援活动的消防员用PPE装备.第5部分:头盔

This document provides the principles that govern the development of incident type and/or hazard specific test methods and minimum performance requirements for helmets for firefighters while engaged in specific rescue activities. Helmets related to specific rescue activities, such as road traffic crash (RTC) and urban search and rescue (USAR), are documented in individual subclauses of this document. NOTE Further guidance can be found in ISO 18639-1. The purpose of this document is to ensure that minimum performance requirements for incident type and/or hazard specific helmets are designated. This document covers general helmet design, the minimum performance level of the materials used and the methods of test for determining this performance level. It does not cover special helmets for use in other high risk situations such as firefighting. This document does not cover protection for the torso, arms, legs and feet or protection of the hands against other hazards, e.g. chemical, biological, radiation and electrical hazards, except for limited, accidental exposure to fire ground chemicals and contaminated blood or body fluids. Selection of the appropriate system of personal protective equipment, (PPE), including helmets, is dependent on carrying out an effective risk assessment which identifies the hazard to be faced, evaluates the likelihood of those hazards and provides the means of reducing or eliminating these hazards.

PPE ensembles for firefighters undertaking specific rescue activities — Part 5: Helmet

BS EN ISO 4869-2:2018 声学 听力保护器 佩戴听力保护器时有效 A 计权声压级的估计

What is ISO 4869‑2- Estimating the A-weighted sound pressure levels effective when hearing protectors are worn about? ISO 4869‑2 discusses hearing protectors. ISO 4869‑2 is an international standard on the estimation of effective A-weighted sound pressure levels when hearing protectors are worn to ensure protection against hazardous noise at the workplace. ISO 4869‑2 is the second part of a multi-part series that specifies three methods of estimating the A-weighted sound pressure levels effective when hearing protectors are worn. The method specified by ISO 4869‑2 applies to either the sound pressure level or the equivalent continuous sound pressure level of the noise. The methods also apply to noises containing impulsive components. Note: It is possible that the methods specified by ISO 4869‑2 could not be suitable for use with peak sound pressure level measurements. Who is ISO 4869‑2- Estimating the A-weighted sound pressure levels effective when hearing protectors are worn for ? ISO 4869‑2 on the estimation of effective A-weighted sou...

Acoustics. Hearing protectors. Estimation of effective A-weighted sound pressure levels when hearing protectors are worn

EN ISO 4869-2:2018 声学.听力保护器.第2部分:当听力保护器磨损时影响性的A-重声压级的评定

This document specifies three methods (the octave-band, HML and SNR methods) of estimating the A-weighted sound pressure levels effective when hearing protectors are worn. The methods are applicable to either the sound pressure level or the equivalent continuous sound pressure level of the noise. Although primarily intended for steady noise exposures, the methods are also applicable to noises containing impulsive components. It is possible that these methods could not be suitable for use with peak sound pressure level measurements. The octave-band, H, M, L or SNR values are suitable for establishing sound attenuation criteria for selecting or comparing hearing protectors, and/or setting minimum acceptable sound attenuation requirements.

Acoustics - Hearing protectors - Part 2: Estimation of effective A-weighted sound pressure levels when hearing protectors are worn (ISO 4869-2:2018)

ASTM F659-10(2018) 滑雪和滑雪板护目镜的标准规格

1.1 This specification covers the minimal requirements of ski and snowboard goggles (intended for nonmotorized use) to provide a reasonable degree of protection against snow and moisture striking or lodging in the eye or surrounding soft tissue. 1.2 The scope of this specification shall include requirements for materials, optical properties, lens strength and retention, labeling, identification, and testing procedures. 1.2.1 Contact lenses, sunglasses, and corrective dress eye wear are not included within the scope of this specification. (Warning—Impact resistant prescription spectacles that conform to the standard specifications of ANSI Z87.1 should be used if spectacles are to be worn under goggle-type eyewear as covered by this specification.) 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Ski and Snowboard Goggles

KS I ISO TR 4869-4-2018 声学 听力保护器 第 4 部分：声级相关声音恢复耳罩的有效声压级测量

Acoustics — Hearing protectors — Part 4: Measurement of effective sound pressure levels for level-dependent soundrestoration ear-muffs

T/ZZB 0658-2018 塑料安全帽

本标准规定了塑料安全帽的分类、基本要求、技术要求、试验方法、检验规则、标志、包装、运输与贮存和质量承诺。 本标准适用于帽壳主体由丙烯腈-丁二烯-苯乙烯（ABS）、高密度聚乙烯(HDPE)、聚丙烯(PP)和聚碳酸脂（PC）等塑料制成的工业用安全帽。 本标准不适用于运动、消防、应急救援、防暴、军事所使用的头部防护装备以及车用头部防护装备。

Plastic safety helmets

ASTM F2397-18 竞技运动用防护帽的标准规范

1.1 This specification covers performance requirements for head protection used for training and competition in combative sports such as karate, wushu, and taekwondo, where normal contact between participants may be repeated, but is limited to a level that is not intended to produce injury. These activities typically take place in indoor or outdoor environments where the temperature is moderate. This specification recognizes the desirability of a lightweight and streamlined construction, and ventilation; however, it is a performance specification, and is not intended to restrict design. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted in this specification. 1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be distributed or sold with any indication that it meets parts of the specification. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Protective Headgear Used in Combative Sports

ISO 4869-1:2018 声学 护听器 第1部分:声衰减测量的主观法

This document specifies a subjective method for measuring sound attenuation of hearing protectors at the threshold of hearing. The method is a laboratory method designed to yield reproducible values under controlled measurement conditions. The values reflect the attenuating characteristics of the hearing protector only to the extent that users wear the device in the same manner as did the test subjects. For a more representative indication of field performance the methods of ISO/TS 4869-5 can be used. This test method yields data which are collected at low sound pressure levels (close to the threshold of hearing) but which are also representative of the attenuation values of hearing protectors at higher sound pressure levels. An exception occurs in the case of amplitude-sensitive hearing protectors for sound pressure levels above the point at which their level-dependent characteristics become effective. At those sound pressure levels the method specified in this document is inapplicable, as it will usually underestimate sound attenuation for these devices. NOTE Due to masking from physiological noise in the occluded ear tests, sound attenuations below 500 Hz can be overestimated by a few decibels.

Acoustics - Hearing protectors - Part 1: Subjective method for the measurement of sound attenuation

DIN EN 14458:2018 个人眼部设备 仅与防护头盔一起使用的高性能护目镜；德文版 EN 14458:2018

This European Standard specifies the minimum requirements for visors designed specifically to be used only with protective helmets e. g. firefighter helmets conforming to EN 443, EN 16471 and EN 16473 and high performance industrial helmets conforming to EN 14052. These visors may be permanently fitted to, or be removable from the helmet. Three types of visors in two forms are described in this document. The two forms are: - face guards provide both eye and face protection, and - eye guards that are shorter and effectively provide only eye protection. The three types are: - visors for general use: eye guards and face guards providing resistance and/or protection against mechanical, liquid chemical and basic physical hazards; - visors with increased thermal performance: face guards that additionally provide resistance and/or protection against higher than basic levels of heat and flame; - mesh visors: eye guards and face guards that incorporate mesh lenses with defined levels of performance from EN 1731, and other additional mechanical requirements described in this European Standard. These visors are not intended to protect against smoke and gas /vapour hazards. Visors for sporting use, those with corrective effect, and goggles used with a protective helmet are not covered by this European Standard.

Personal eye-equipment - High performance visors intended only for use with protective helmets; German version EN 14458:2018

ISO 4869-2:2018 声学 护听器 第2部分:佩带护听器时有效A-计权声压级的估算

This document specifies three methods (the octave-band, HML and SNR methods) of estimating the A-weighted sound pressure levels effective when hearing protectors are worn. The methods are applicable to either the sound pressure level or the equivalent continuous sound pressure level of the noise. Although primarily intended for steady noise exposures, the methods are also applicable to noises containing impulsive components. It is possible that these methods could not be suitable for use with peak sound pressure level measurements. The octave-band, H, M, L or SNR values are suitable for establishing sound attenuation criteria for selecting or comparing hearing protectors, and/or setting minimum acceptable sound attenuation requirements.

Acoustics - Hearing protectors - Part 2: Estimation of effective A-weighted sound pressure levels when hearing protectors are worn

ASTM F2713-18 曲棍球眼保护器标准规范

Standard Specification for Eye Protectors for Field Hockey