13.340.20 头部防护设备 标准查询与下载

ASTM F2040-18 休闲雪地运动用头盔的标准规范

1.1 This specification defines performance requirements for helmets used in nonmotorized recreational snow sports (such as skiing, snowboarding, and other alpine sports). This specification is a performance standard and is not intended to restrict design. Although a helmet that meets this specification will help reduce the risk of some types of injuries to the head at slower speeds, the protection is limited. The user is responsible for participating in the sport within his/her abilities and the nature of the snow conditions which may vary widely. Compliance with the common sense rules of the sport’s safety, including any applicable responsibility codes, is essential to help reduce the risk of personal injury. 1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. 1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the standard and should not be sold with any indication that it meets parts of the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Helmets Used for Recreational Snow Sports

ASTM F2812-12(2018) 护目镜和眼镜型护目镜的标准规格

1.1 This specification covers eye protectors, exclusive of helmet-mounted visors, designed for use by riders of motorcycles, mopeds, and snowmobiles for off road use that minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration by objects that may be kicked up from the road, track, trail, or snow surfaces and made airborne and, as such, likely to cause eye discomfort or injury. This specification does not address shield-type eye protectors such as are connected to, integral to, and/or supported by protective helmets. Protective eyewear offers protection only to the eyes and does not protect other parts of the head, face, or neck. 1.2 Protectors are divided into two types, goggles or spectacles, depending on their design characteristics. 1.3 This specification does not apply to prescription eyewear. (Warning—Impact-resistant prescription spectacles that conform to the standard specifications of ANSI Z87.1 should be used if spectacles are to be worn under goggle-type eyewear as covered by this specification.) 1.4 In this specification, the use of the word “shall” indicates a mandatory requirement. The word “should” indicates a recommendation. 1.5 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measure in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Goggle- and Spectacle-Type Eye Protectors for Selected Motor Sports

KS P ISO 6161:2017 个人用目镜 防激光辐射的滤光镜和护目镜

Personal eye-protectors — Filters and eye-protectors against laser radiation

KS P ISO 6161-2017 个人护目镜 - 防止激光辐射的过滤器和防护眼镜

Personal eye-protectors — Filters and eye-protectors against laser radiation

BS EN 13277-8:2017 武术防护装备 空手道面部保护器的附加要求和试验方法

Protective equipment for martial arts. Additional requirements and test methods for karate face protectors

ISO 21924-4:2017 武术防护装备 - 第4部分:头部保护装置的附加要求和试验方法

This document specifies additional requirements and test methods for head protectors without face protection used in unarmed martial arts, such as taekwondo, karate, kick-boxing and similar disciplines. It also applies to head protectors used in boxing.

Protective equipment for martial arts — Part 4: Additional requirements and test methods for head protectors

EN 13277-8:2017 武术用护具 第8部分：空手道护面器的附加要求和试验方法

Protective equipment for martial arts - Part 8: Additional requirements and test methods for karate face protectors

ASTM F2178-17b 用于确定眼睛或面部防护产品的电弧等级和标准规范的标准测试方法

Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products

ASTM F2439-17e1 足球用头盔标准规范

1.1 This specification defines performance requirements for headgear used for participation in the sport of soccer. The technical requirements in this specification do not address the administrative requirements of soccer governing bodies, so it should not be assumed that any headgear satisfying this specification will be acceptable for use in sanctioned soccer events. 1.2 This specification is intended to reduce the forces from external physical sources reaching the defined impact area of the head in impacts that may occur in the sport of soccer. No headgear can provide protection against all impacts, foreseeable or not. This specification does not address the potential for injury from any type of impact. The tests specified in this specification are laboratory simulation tests only, and do not purport to create situations identical to the impacts that may occur during the playing of soccer. 1.3 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein. In the event of a discrepancy between the requirements of this specification and those of Test Methods F1446, this specification shall prevail. 1.4 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the headgear meets all of the requirements of this specification in its entirety. Headgear that fails to meet any one of the requirements of this specification is considered to have failed the specification and should not be sold with any indication that it meets parts of the specification. 1.5 The values stated in SI units are to be regarded as the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Headgear Used in Soccer

ASTM F2178-17a 用于确定眼睛或面部防护产品的电弧等级和标准规范的标准测试方法

Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products

ASTM F2439-17 足球用头盔标准规范

Standard Specification for Headgear Used in Soccer

EN 13911:2017 消防员防护服.消防员防火罩的要求和试验方法

Protective clothing for firefighters - Requirements and test methods for fire hoods for firefighters

ASTM F2178-17 用于确定眼睛或面部防护产品的电弧等级和标准规范的标准测试方法

1.1 This test method and product specification is used to measure the arc rating and specify the requirements for products intended for use as eye or face protection for workers exposed to electric arcs that would generate heat flux values from 84 to 25 120 kW ⁄m2 [2 to 600 cal/cm2 s]. Products are tested as sold. 1.2 This test method determines an arc rating for eye or face protective products. The faceshield, safety spectacle, goggle or or other applicable portions of the complete product must meet ANSI Z87.1. This excludes the textile or non ANSI Z87.1 testable parts of the hood assemblies or other tested products. This standard does not measure optical and impact properties (see ANSI Z87.1) but does specify requirements for optical and impact properties. 1.3 The materials covered by this standard are in the form of faceshields attached to the head by protective helmets (hard hats), headgear, hood assemblies, safety spectacles or goggles. Faceshields, safety spectacles or goggles are tested with or without other face and head protective products, for example, sock hoods, balaclavas, sweat shirt hoods or jacket hoods. 1.3.1 Fabric layers used in hood assemblies or other items tested under this standard shall meet the requirements of Specification F1506. 1.4 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions and does not purport to predict damage from light other than the thermal aspects measured. 1.5 The values stated in SI units shall be regarded as standard except as noted. Within the text, alternate units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, alternate systems must be used independently of the other. Combining values from the systems described in the text may result in nonconformance with the method. 1.6 This standard does not purport to describe or appraise the effect of the electric arc fragmentation explosion and subsequent molten metal splatter, which involves the pressure wave containing molten metals and possible fragments of other materials except to the extent that heat energy transmission due to these arc explosion phenomena is reduced by test specimens. 1.7 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.For specific precautions, see Section 7. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products

EN 1384:2017 骑马防护头盔

Helmets for equestrian activities

DIN EN 207:2017 个人护目镜.防激光辐射滤光镜和护目镜(激光护目镜);德文版本EN 207-2017

Personal eye-protection equipment - Filters and eye-protectors against laser radiation (laser eye-protectors); German version EN 207:2017

DIN EN ISO 10256-1:2017 冰球运动员用保护装备.第1部分:一般要求(ISO 10256-1-2016);德文版本EN ISO 10256-1-2016

Protective equipment for use in ice hockey - Part 1: General requirements (ISO 10256-1:2016); German version EN ISO 10256-1:2016

BS EN 207:2017 个人护眼设备 防止激光辐射的滤光片和护目镜（激光护眼镜）

Personal eye-protection equipment. Filters and eye-protectors against laser radiation (laser eye-protectors)

EN 207:2017 个人护目镜.防激光辐射滤光镜和护目镜(激光护目镜)

This European Standard applies to eye-protectors used for protection against accidental exposure to laser radiation as defined in EN 60825-1:2007 in the spectral range 180 nm (0,18 µm) to 1000 µm. It defines the requirements, test methods and marking. A guide is given in the informative Annex B for the selection and use of laser eye-protectors and filters in appliances. This European Standard does not apply to protectors for intentional exposure to laser radiation. EN 208 applies to laser adjustment eye-protectors. Before selecting eye protection according to this European Standard, a risk assessment should first be undertaken.

Personal eye-protection equipment - Filters and eye-protectors against laser radiation (laser eye-protectors)

GOST R 57560-2017 头盔 分类 术语和定义

Helmets. Classification. Terms and definitions

ASTM F2178-17(2017) 表面保护产品电弧额定值测定的标准试验方法

1.1 This test method and product specification is used to measure the arc rating and specify the requirements for products intended for use as eye or face protection for workers exposed to electric arcs that would generate heat flux values from 84 to 25 120 kW ⁄m2 [2 to 600 cal/cm2 s]. Products are tested as sold. 1.2 This test method determines an arc rating for eye or face protective products. The faceshield, safety spectacle, goggle or or other applicable portions of the complete product must meet ANSI Z87.1. This excludes the textile or non ANSI Z87.1 testable parts of the hood assemblies or other tested products. This standard does not measure optical and impact properties (see ANSI Z87.1) but does specify requirements for optical and impact properties. 1.3 The materials covered by this standard are in the form of faceshields attached to the head by protective helmets (hard hats), headgear, hood assemblies, safety spectacles or goggles. Faceshields, safety spectacles or goggles are tested with or without other face and head protective products, for example, sock hoods, balaclavas, sweat shirt hoods or jacket hoods. 1.3.1 Fabric layers used in hood assemblies or other items tested under this standard shall meet the requirements of Specification F1506. 1.4 This test method shall be used to measure and describe the properties of materials, products, or assemblies in response to convective and radiant energy generated by an electric arc under controlled laboratory conditions and does not purport to predict damage from light other than the thermal aspects measured. 1.5 The values stated in SI units shall be regarded as standard except as noted. Within the text, alternate units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, alternate systems must be used independently of the other. Combining values from the systems described in the text may result in nonconformance with the method. 1.6 This standard does not purport to describe or appraise the effect of the electric arc fragmentation explosion and subsequent molten metal splatter, which involves the pressure wave containing molten metals and possible fragments of other materials except to the extent that heat energy transmission due to these arc explosion phenomena is reduced by test specimens. 1.7 This standard shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.For specific precautions, see Section 7. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining The Arc Rating Of Face Protective Products