共找到 1259 条与 计量学和测量综合 相关的标准,共 84 页
适用于远程智控方舱计量实验室的基本要求、结构要求、资源要求、过程要求和管理体系要求。
Requirements for remote intelligent control shelter metrology laboratory
Integrity Measurement Management Specification Part 3: Gas Stations
Integrity Measurement Management Regulations Part 1: Bazaars
Integrity Measurement Management Regulations Part 4: Spectacle Fitting Enterprises
Discontinuous totalizing automatic weighing instruments (totalizing hopper weighers)-Part 2:Test report format
Discontinuous totalizing automatic weighing instruments (totalizing hopper weighers)-Part 1:Metrological and technical requirements-Tests
Physical structure and Protocol for electronic gas meter based on command type
Measurement management and service specifications for bottled liquefied petroleum gas filling stations
General technical requirements for equivalent anti-flux transient electromagnetic detection system
Specifications for metering management of natural gas filling stations
本文件规定了在标准、图样、设计文件、工艺文件、记录、宣传资料等文件中计量单位及测量设备 计量特性的表示方法。
Measurement units, measurement characteristics of the method
本标准适用的近眼显示系统检测装置是专门针对AR/VR显示设备、头盔显示设备等智能可穿戴近眼显示设备进行检测的检测装置,该装置可以模拟人眼的运动状况,开展包括MTF测试、视场角检测、亮度和色度测试等关键光学指标的检测。本标准仅针对近眼显示系统检测装置的光学测量性能和电气安全性能进行规定,机械控制部分的性能不做要求。 本标准的内容分为前言、正文和附录三部分。 1.前言 写明了标准的编制规则,归口单位,起草单位等信息。 2.正文 正文部分包含8个章节: (1)适用范围 说明标准的适用范围。 (2)规范性引用文件 列明标准引用的文件。 (3)术语、定义 针对文中出现的术语给出定义。 (4)系统构成 说明近眼显示系统检测装置的系统组成。 (5)基本要求 对近眼显示系统检测装置的基本要求,包括:外观和结构要求、安全要求和通用计量性能要求、亮度和色度计量性能要求要求。 (6)检验方法 说明检测装置的检验条件、检验所需设备和检验方法。 (7)检验规则 针对型式检验、逐批检验和周期检验提出不同的检验规则。 (8)标准、包装、运输和贮存 针对检测装置的标志、包装、运输和贮存提出要求。 3.附录 附录给出检验过程中所需的标准图形样例。
Technical Requirements and Testing Methods of Inspection Device for Near-eye Display System
Service Specifications for Metrology and Calibration Institutions
In general, the measuring systems that are covered by this Recommendation are intended for the refueling of motor vehicles, small boats, and aircraft with compressed natural gas, hydrogen, biogas, gas blends or other compressed gaseous fuels. They may also be applicable to other vehicles, for instance trains. Measuring systems for liquid petroleum gas are not included in the scope of this Recommendation. These are within the scope of OIML R 117, which covers fluids in a liquid state. In principle, this Recommendation applies to all measuring systems fitted with a meter as defined in 3.2.2 (continuous measurement), whatever the measuring principle may be of the meters or their application. This Recommendation is not intended to prevent the development of new technologies. According to the state of the art, this Recommendation is intended for measuring systems providing mass indications.
Compressed gaseous fuel measuring systems for vehicles. Part 1: Metrological and technical requirements
IEC 62828-1:2017 establishes a general framework for defining reference conditions and test procedures applicable to all types of industrial and process measurement transmitters (PMTs) used in measuring and control systems for industrial process and machinery. These reference test conditions are divided into “standard reference conditions”, which apply when determining the accuracy of measurement, and “ambient and process reference conditions”, which are used to assess the influence of external quantities on the measurement. The IEC 62828 series cancels and replaces the IEC 60770 series and proposes revisions for the IEC 61298 series.
Reference conditions and procedures for testing industrial and process measurement transmitters - Part 1: General procedures for all types of transmitters
Scope is not provided for this standard
Instruments for the continuous measurement of CO and NOx in stationary source emissions- Part 2: Test procedures
Implementation of this report format is informative with regard to the implementation of OIML R 139-1 and -2 in national regulations. However, its implementation is mandatory within the framework of the OIML Certificate System for Measuring Instruments. Note concerning the references: All references are to the combined publication OIML R 139-1 and -2:2014. In this report format this publication is referred to as “R 139”. This report format applies for any kind of compressed gaseous fuel measuring system for vehicles (independent of its technology). It presents a standardized format for recording the results of the various tests and examinations, described in R 139-2:2014, to which a type of a compressed gaseous fuel measuring system for vehicles shall be submitted with a view to its approval based on this OIML Recommendation.
Compressed gaseous fuel measuring systems for vehicles. Part 3: Test report format
This Recommendation covers requirements for the labeling of prepackages with respect to a) the identity of the product, b) the declaration of responsibility for a prepackage, and c) the quantity of product in the prepackage
Labeling requirements for prepackages
Inspection and testing safety protection specifications
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号