17.040.10 极限和配合 标准查询与下载

DS/EN 22768-2:1993 一般公差．第2部分：无专门公差指示的特性几何公差

This part of ISO 2768 is intended to simplify drawing indica-tions and specifies general geometrical tolerances to control those features on the drawing which have no respective in-dividual indication. It specifies general geometrical tolerances in three tolerance classes. This part of ISO 2768 mainly applies to features which are pro-duced by removal of material. Its application to features manufactured by other processes is possible; however, special examination is required to ascertain whether the customary workshop accuracy lies within the general geometrical toler-ances specified in this part of ISO 2768.

General tolerances. Part 2: Geometrical tolerances for features without individual tolerance indications

BS EN 22768-2:1993 一般公差.第2部分:未单独标注公差要素的几何公差

This part of ISO 2768 is intended to simplify drawing indica-tions and specifies general geometrical tolerances to control those features on the drawing which have no respective in-dividual indication. It specifies general geometrical tolerances in three tolerance classes. This part of ISO 2768 mainly applies to features which are pro-duced by removal of material. Its application to features manufactured by other processes is possible; however, special examination is required to ascertain whether the customary workshop accuracy lies within the general geometrical toler-ances specified in this part of ISO 2768.

General tolerances - Geometrical tolerances for features without individual tolerance indications

EN 22768-1:1993 通用公差.第1部分:无单项公差标注的线性和角度尺寸公差(ISO 2768-1-1989)

This part of ISO 2768 is intended to simplify drawing indica-tions and it specifies general tolerances for linear and angular dimensions without individual tolerance indications in four tol-erance classes.

General tolerances; part 1: tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989)

EN 22768-2:1993 通用公差.第2部分:未单独标注公差的几何公差(ISO 2768-2-1989)

This part of ISO 2768 is intended to simplify drawing indica-tions and specifies general geometrical tolerances to control those features onThe drawing which have no respective in-dividual indication. It specifies general geometrical tolerances in three tolerance classes.This part of ISO 2768 mainly applies to features which are pro-duced by removal of material. Its application to features manufactured by other processes is possible; however, special examination is required to ascertain whetherThe customary workshop accuracy lies withinThe general geometrical toler-ances specified inThis part of ISO 2768.

General tolerances; part 2: geometrical tolerances for features without individual tolerance indications (ISO 2768-2:1989)

KS B 0146-1992(2002) 正常公差 - 第2部分:几何公差的成型除非得到个人容忍这样做

GENERAL TOLERANCES-PART2:GEOMETRICAL TOLERANCES FOR FEATURES WITHOUT INDIVIDUAL TOLERANCE INDICATIONS

CSN ISO 2768-1:1992 一般公差．第1部分：无单独公差标示的线性和角度尺寸公差

Zpracovatel: ?koda, koncern, Plzeň, a. s., I?O 213 101, Ing. Miloslav S?kora Pracovník Federálního ú?adu pro normalizaci a mě?ení: Ing. Pavel Dvo?ák

General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications

SNI 05-2637-1992 无规定公差金属片偏差尺寸

Permissiable deviation without tolerance indication for press working of sheet metal

SNI 05-2639-1992 铸铁产品允许偏差尺寸

Permissible deviation without tolerance indication for die casting

SNI 05-2641-1992 铸铁器件尺寸公差系统

System of dimensional tolerances of castings

DIN ISO 2768-1:1991 通用公差.第1部分:不逐一标注公差的线性尺寸和角度尺寸公差

The standard is intended to simplify drawing indications. It specifies general tolerances in 4 tolerance classes, which consider the respective customary workshop accuracy. The ISO 2768-1 is a revision of ISO 2768-1974 based on DIN 7168 part 1.#,,#

General tolerances; tolerances for linear and angular dimensions without individual tolerance indications; identical with ISO 2768-1:1989

DIN 7168:1991 长度和角度尺寸的一般公差和形位公差 (不适用于新设计)

The standard covers the former standards DIN 7168 part 1 and part 2 completely under one number. It shall not be used on new drawings. For new drawings DIN ISO 2768 part 1 and part 2 are to be considered.

General tolerances for linear and angular dimensions and geometrical tolerances (not to be used for new designs)

DIN ISO 2768-2:1991 通用公差.第2部分:未标注专用公差的功能部件用形位公差; 等同采用 ISO 2768-2:1989

General tolerances; geometrical tolerances for features without individual tolerances indications; identical with ISO 2768-2:1989

DIN 7172:1991 规格范围在 3150 mm - 10.000 mm 以上的公差和极限偏差.原则、标准公差和极限偏差

Tolerances and limit deviations for sizes above 3150 mm up to 10000 mm; principles, standard tolerances and limit deviations

JIS B 0419:1991 一般公差.第2部分:未单独标注公差的零件的几何公差

この規格は，図面指示を簡単にすることを意図し，個々に幾何公差の指示がない形体を規制するための三つの公差等級の普通幾何公差(general geometrical tolerance)について規定する。この規格は，主として除去加工(removal of material)によって製作した形体に適用する。他の加工方法によって製作した形体にこれを適用することができるが，通常の工場で得られる加工精度がこの規格に規定された普通幾何公差内にあるかどうかについて確認することが必要である。

General tolerances -- Part 2: Geometrical tolerances for features without individual tolerance indications

JIS B 0405:1991 普通公差. 第1部分:无单独公差指示的线性及角度尺寸公差

この規格は，図面指示を簡単にすることを意図し，個々に公差の指示がない長さ寸法及び角度寸法に対する四つの公差等級の普通公差(general tolerance)について規定する。備考1. 長さ寸法及び角度寸法に対する普通公差表示方式の背景にある概念は，附属書Aに述べる。この規格は，金属の除去加工(metal removal)又は板金成形(forming from sheet metal)によって製作した部品の寸法に適用する。2.これらの公差は，金属以外の材料に適用してもよい。3.類似の規格があり，又は計画されている。例えば，鋳造品に対するJIS B 0403(鋳造品-寸法公差方式)参照。参考 JIS B 0403-1987は，ISO 8062:1984 (Castings-System of dimensional tolerances)の国際一致規格である。この規格は，個々に公差指示がない次の寸法にだけ適用する。(a)長さ寸法(例えば，外側寸法，内側寸法，段差寸法，直径，半径，間隔，かどの丸み及びかどの面取寸法)。(b)角度寸法[通常，図面に指示されなしい角度，例えば，JIS B 0419が引用されていない直角（90°），又は正多角形の角度を含む。]。(e)組立品を機械加工して得られる長さ寸法及び角度寸法。この規格，次の寸法には適用しない。(a)普通公差についての別の規格が適用される長さ寸法及び角度寸法。(b)括弧内に指示した参考寸法。(c)長方形の枠内に指示した理論的に正しい寸法。

General tolerances -- Part 1: Tolerances for linear and angular dimensions without individual tolerance indications

DIN ISO 286-2:1990 ISO系统的公差与配合 .第2部分:孔和轴的标准公差级和极限偏差表

ISO system of limits and fits; tables of standard tolerance grades and limit deviations for holes and shafts; identical with ISO 286-2:1988

DIN ISO 286-1:1990 ISO公差配合系统.第1部分:公差基础.偏差和配合

The standard gives the bases of the ISO system of limits and fits together with the calculated values of the standard tolerances and fundamental deviations. These values shall be taken as authoritative for the application of the system. The standard also gives terms and definitions together with associated symbols. The ISO system of limits and fits provides a system of tolerances and deviations suitable for plain workpieces.

ISO system of limits and fits; bases of tolerances, deviations and fits; identical with ISO 286-1:1988

ISO 2768-1:1989 一般公差 第1部分:未注公差的线性和角度尺寸的公差

This part is intended to simplify drawing indications and specifies general tolerances in four tolerance classes. It applies to the dimensions of workpieces that are produced by metal removal or are formed from sheet metal. It contains three tables and an informative annex with regard to concepts behind general tolerancing of dimensions.

General tolerances; part 1: tolerances for linear and angular dimensions without individual tolerance indications

ISO 2768-2:1989 一般公差 第2部分:未注公差的要素的几何公差

This part is intended to simplify drawing indications and specifies general tolerances in three tolerance classes. It mainly applies to features which are produced by removal of material. It contains tour tables and an informative annex A with regard to concepts behind general tolerancing of dimensions, as well as an informative annex B with further information.

General tolerances; part 2: geometrical tolerances for features without individual tolerance indications

CSN 01 0202-1988 标称线性尺寸

1. Autor — delegace SSSR ve Stálé komisi RVHP pro spolupráci v oblasti normalizace 2. ?kol - 01.402.24-87 3. Norma RVHP byla schválena na 63. zasedání SKSN. 4. Termíny po?átku uplatnění normy RVHP: ?lenské státy RVHP Termíny po?átku uplatnění normy RVHP ve smluvně právních vztazích p?i hospodá?ské a vědeckotechnické spolupráci v národním hospodá?ství BLR MLR VSR NDR Rep. Kuba MoLR PLR RSR SSSR ?SSR leden 1990 leden 1989 leden 1991 leden 1990 leden 1991 ?ervenec 1989 leden 1990 leden 1990 leden 1989 leden 1991 ?ervenec 1991 leden 1991 leden 1990 leden 1990 5. Termín prověrky — 1997 6. Pou?ité mezinárodní dokumenty: Norma RVHP odpovídá normám ISO 3-73 a ISO 497-73 pokud jde o ?ady vyvolen?ch ?ísel R 5, R 10, R 20, R 40, R 80, R”5, RT0, R”10, R’20, R”20, R’40 a ISO 17-73 pokud jde o tvo?ení odvozen?ch ?ad.

Nominal linear sizes