17.040.10 极限和配合 标准查询与下载

BS 4500-5:1988 ISO 极值与配合.锥度C从1:3至1:500、长度6mm至630mm的锥形工件锥度公差体系规范

Specifies a system which applies to rigid workpieces for which the length of the generator can be considered as practically equal to the basic cone length.

ISO limits and fits - Specification for system of cone tolerances for conical workpieces from C = 1:3 to 1:500 and lengths from 6 mm to 630 mm

ISO 286-1:1988 ISO极限和配合体系；第1部分：公差、偏差和配合的基础

This part gives the bases of the ISO system of limits and fits together with the calculated values of the standard tolerances and fundamental deviations. It also gives terms and definitions together with associated symbols.

ISO system of limits and fits; part 1: bases of tolerances, deviations and fits

ISO 286-2:1988 ISO极限和配合体系；第2部分：孔和轴的标准公差等级和极限偏差表

This part gives of the limit deviations for commonly used tolerance classes calculated from the information given in ISO 286-1. It covers values for the upper and the lower deviations which are illustrated by a figure. It tabulates numerical values for basic sizes from 3 mm up to and including 3150 mm. An annex gives a graphical review of tolerance zones.

ISO system of limits and fits; part 2: tables of standard tolerance grades and limit deviations for holes and shafts

ANSI/ASTM D3297:1988 PTFE树脂零件的模塑和机加工公差的实施规程(08.03)

This practice defines tolerances applicable to parts molded and free sintered from PTFE resins and to machined parts produced from basic shapes of compression-molded or ram-extruded resins. The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety standards, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Practice for Molding and Machining Tolerances for PTFE Resin Parts (08.03)

CNS 4-2-1987 限界与配合(一般工件之检验)

本标准适用于一般工件之检验。本标准叙述尺度限界检验之说明，并提供检验 ISO 公差制所需限规及指示测定义之必要细节。

Limits and Fits (Inspection of Plain Workpieces)

CNS 4.2-1987 限界与配合（一般工件之检验）

Limits and Fits (Inspection of Plain Workpieces)

JIS B 0614:1987 锥度公差体系

この規格は，テーパ比が1/3～1/500，円すい長さが6 mmを超え，630mm以下の剛性のある円すい部品に適用する円すい公差方式について規定する。ただし，転がり軸受の円すい公差には適用しない。なお，この規格に定めるテーパ角度公差は，プリズム部品にも適用することができる。

System of cone tolerances

JIS B 0612:1987 圆锥度

Conical tapers

CNS 4022-1987 一般许可差（压铸）

本标准规定铝合金及锌合金压铸件未标注尺度许可差或记号之许可差准则。

Permissible Deviations in Dimensions Without Tolerance Indication (Die Castings)

CNS 4-1-1987 限界与配合(公差与偏差制度)

本标准适用于 500 mm 以下之机械制件尺寸之公差与配合，及超过 500 mm 至 3150 mm 之机械制件尺寸公差。因圆柱体占有特别重要地位，为简单起见，本标准采用统一术语「孔」或「轴」。凡任何制件之二平行面（或切线平面）间所含的空间，适用「孔」的标准，凡任何制件之二平行

Limits and Fits (General, Tolerance and Deviations)

CNS 4026-1987 一般许可差（金属烧结品）

本标准规定作为机械零件用之金属烧结品未标注尺度许可差或记号的许可差准则。

Permissible Deviations in Dimensions Without Tolerance Indication (Metallic Sintered Products)

CNS 4.1-1987 限界与配合（公差与偏差制度）

Limits and Fits (General, Tolerance and Deviations)

DIN 7167:1987 尺寸,形状和平行度公差之间的关系.图纸上无单独说明的图形包络线要求

Relationship between tolerances of size, form, and parallelism; envelope requirement without individual indication on the drawing

DIN 7178-4:1986 锥度C=1:3至1:500及长度6至630mm的锥形工件的圆锥公差与配合体系.轴向位移

System of cone tolerances and cone fits for conical workpieces of cones from C = 1 : 3 to 1 : 500 and lengths from 6 to 630 mm; axial displacements

DIN 7178-3:1986 锥度C=1:3至1=500及长度6至630mm的锥形工件的圆锥公差与配合体系.圆锥偏差对圆锥配合的影响

Together with DIN 7178 part 2 and part 4 this DIN-Standard specifies the system of cone fits according to ISO 5166-1982, which is based on the system of cone tolerances according to ISO 1947-1973.#,,#

System of cone tolerances and cone fits for conical workpieces of cones from C = 1 : 3 to 1 : 500 and lengths from 6 to 630 mm; effect of the deviations on cone with regard to the cone fit

DIN 7178-2:1986 锥度C=1:3至1:500及长度6至630mm的锥形工件的圆锥公差与配合体系.圆锥配合体系

Together with DIN 7178 part 3 and part 4 this DIN-Standard specifies the system of cone fits according to ISO 5166-1982, which is based on the system of cone tolerances according to ISO 1947-1973.#,,#

System of cone tolerances and cone fits for conical workpieces of cones from C = 1 : 3 to 1 : 500 and lengths from 6 to 630 mm; system of cone fits

JIS B 0401:1986 尺寸公差与配合

System of limits and fits

BS 4500-4:1985 ISO 极值与配合.第4部分:锥度C=1:3至1:500、长度6mm至630mm和直径不超过500mm的圆锥(锥度)配合制规范

Applies to cones which are dimensioned and toleranced according to method 1 (basic taper method) of ISO 3040. Specifies a hole basis system of fits.

ISO limits and fits - Specification for system of cone (taper) fits for cones from C=1:3 to 1:500, lengths from 6 mm to 630 mm and diameters up to 500 mm

CSN 01 0211-1985 圆角半径与边缘切角

Fillet radii and chamfering of edges

JIS B 0621:1984 几何偏差的定义及名称

この規格は，対象物の形状偏差，姿勢偏差，位置偏差及び振れ(以下，これらを総称して幾何偏差という。)の定義及び表示について規定する。備考 幾何偏差の許容値である幾何公差の紀号による表示及びそれらの図示方法については，JIS B 0021(幾何公差の図示方法)による。

Definitions and designations of geometrical deviations