17.040.10 极限和配合 标准查询与下载

CSN 01 4276-1982 圆锥组装公差与配件系统

Schválení ST SEV 1780-79 doporu?ilo federální ministerstvo v?eobec-ného strojírenství. Zpracovatel: Závody p?esného strojírenství, k. p. Gottwaldov, Ing. Jo-sef Staněk Pracovník ??adu pro normalizaci a mě?ení: Ing. Zdeněk Stoud

System for tolerances and fits for conical assembly

JIS B 0615:1982 机械用棱体的角度及斜度

Angles and slopes on prisms

BS 969:1982 普通极限量规的极限和公差规范

Tables for tolerances on plug, bar, rod, pin, ring and gap gauges based on a graded series of work tolerances from 0.009 to 3.2 mm. Examples of the use of the tables gauges in imperial units and principles of inspection using plain limit gauges are appended.

Specification for limits and tolerances on plain limit gauges

DIN ISO 5459:1982 技术制图.几何公差.几何图形公差的基准和基准系统

Technical drawings; geometrical tolerancing; datums and datum-systems for geometrical tolerances

JIS B 0409:1980 压铸件一般允许偏差

Permissible deviations in dimensions without tolerance indication for die castings

CSN 01 4405-1979 形位公差．数值s

Schválení ST SEV 636-77 doporu?ilo federální ministerstvo hut-nictví a tě?kého strojírenství. Zpracovatel: ?koda, oborov? podnik, Plzeň - Ladislav Runt Pracovník ??adu pro normalizaci a mě?ení: Ing. Zdeněk ?toud

Tolerances of form and of position. Numerical values

JIS B 0414:1978 铝合金铸件一般允许偏差

Permissible deviations in dimensions without tolerance indication for aluminium alloy castings

ASME B4.2-1978 优选米制公差与配合

This standard describes the ISO system of limits and fits for mating parts as it is approved for general engineering usage in the United States of America. It establishes: (1) the designation symbols used to define specific dimensional limits on drawings, material stock, related tools, gages, etc., (2) the preferred basic sizes (first and second choices), (3) the preferred tolerance zones (first, second and third choices), (4) the preferred limits and fits for sizes (first choice only) up to and including 500 millimeters, and (5) definitions of related terms. Tolerance zones for basic sizes in the range from 500 to 3150 mm are specified in Appendix B. The general terms hole and shaft can also be taken as referring to the space contained by two parallel faces of any part, such as the width of a slot, the thickness of a key, etc.

Preferred Metric Limits and Fits

ANSI B4.3-1978 米制尺寸制品的一般公差

Shows how to specify the general tolerances for metric dimensions without tolerance designation.

General Tolerances for Metric Dimensioned Products

ASME B4.3-1978 米制尺寸产品通用公差

This standard shows how to specify the general tolerances for metric dimensions without tolerance designation. The fine and medium tolerance series, as shown in Table 1, are mostly applicable to machined parts, and the coarse series show tolerances for use on all types of dimensions.

General tolerances for metric dimensioned products

ANSI B4.2-1978 优选的米制公差与配合

Describes the ISO system of limits and fits for mating parts as it is approved for general engineering usage in the United States of America.

Preferred Metric Limits and Fits

ANSI/ASME B4.2-1978 优选米制限值和配合

Describes the ISO system of limits and fits for mating parts as it is approved for general engineering usage in the United States of America.

Prefered Metric Limits And Fits

CSN 01 4270-1977 部件可互换性．角公差

Schválení ST SEV 178-75 doporu?ilo Federální ministerstvo v?eobec-ného strojírenství. Zpracovatel: Závody p?esného strojírenství, Gottwaldov, Ing. Josef Staněk Pracovník ??adu pro normalizaci a mě?ení: Ing. Zdeněk ?toud

Interchangeability of parts. Angle tolerances

CSN 01 4203-1976 CMEA极限与配套统一体系．3150mm以上尺寸用公差与偏离度

Schválení ST SEV 177-75 doporu?ilo federální ministerstvo hutnictví a tě?kého strojírenství. Zpracovatel: ?koda, oborov? podnik, Plzeň - Ladislav Runt Pracovník ??adu pro normalizaci a mě?ení: Ing. Zdeněk ?oud

Unified system of limits and fits CMEA. Tolerance and deviations for sizes above 3150 mm

JIS B 0613:1976 中心距的偏差

この規格は，次に示す中心距離の許容差(以下，許容差という。)について規定する。(1)機械部分にあけられたニつの穴の中心距離。(2)機械部分における二つの軸の中心距離。(3)機械部分に加工された二つのみぞの中心距離。(4〕機械部分における穴と軸，穴とみぞ又は軸とみぞとの中心距離。備考 ここにいう穴，軸及びみぞは，それらの中心線が互いに平行でぁり，穴及び軸は円形断面でテーパがなく，みぞは両側面が平行なものとする。

Deviations for centre distance

DIN 7178-5:1976 锥度C=1:3至1:500及长度为6至630mm的锥形工件的圆锥公差与配合体系.德语、英语、法语、意大利语、俄语及西班牙语的词汇

System of cone tolerances and cone fits for conical workpieces of cones from C = 1 :3 to 1:500 and lengths from 6 to 630 mm; vocabulary in German, English, French, Italian, Russian, SpanishDiese Norm stimmt inhaltlich überein mit dem Dokument ISO/TC 3/SC

System of cone tolerances and cone fits for conical workpieces of cones from C = 1 : 3 to 1 : 500 and lengths from 6 to 630 mm; vocabulary in German, English, French, Italian, Russian, Spanish

ISO 1829:1975 一般用途公差带的选择

Gives the possibility of a very extended selection of different symbols for tolerance zones. Includes upper and lower deviations for holes (internal features) and shafts (external features). Gives recommendations for selection.

Selection of tolerance zones for general purposes

DIN 7178-1:1974 锥形工件C=1:3至1:500及长度6至630mm的圆锥公差与配合体系.圆锥公差体系

System of cone tolerances and cone fits for conical workpieces from C = 1: 3 to 1 : 500 and lengths from 6 to 630 mm; system of cone tolerancesZusammenhang mit der von der International Organization for Standardization (ISO) herausgegebenen Norm ISO 1947

System of cone tolerances and cone fits for conical workpieces from C = 1 : 3 to 1 : 500 and lengths from 6 to 630 mm; system of cone tolerances

ISO 2768:1973 未标注公差的尺寸允许加工偏差

Permissible machining variations in dimensions without tolerance indication

DIN 7178-1 Bb.1:1973 锥形工件C=1:3至1:500及长度6至630mm的圆锥公差与配合体系.内外圆锥的检验方法

System of cone tolerances and cone fits for conical workpieces of cones from C = 1 : 3 to 1 : 500 and lenghts from 6 to 630 mm; methods for testing of internal and external cones