17.040.40 标准查询与下载

22/30449703 DC BS EN ISO 18183-1 产品几何规格 (GPS) 分区 第 1 部分：基本概念

BS EN ISO 18183-1. Geometrical product specifications (GPS). Partition - Part 1. Basic concepts

22/30449707 DC BS EN ISO 18183-2 产品几何规格 (GPS) 分区 第 2 部分：标称模型

BS EN ISO 18183-2. Geometrical product specifications (GPS). Partitioning - Part 2. Nominal model

22/30449711 DC BS EN ISO 18183-3 产品几何规格 (GPS) 分区 第 3 部分：用于规范和验证的方法

BS EN ISO 18183-3. Geometrical product specifications (GPS). Partitioning - Part 3. Methods used for specification and verification

GSO ISO 23276:2022 产品几何规格 (GPS) 表面纹理：轮廓法 PSm、RSm、WSm 和 Pc、Rc、Wc 流程图

This document provides an unambiguous calculation of parameters PSm, RSm, WSm and Pc, Rc, Wc, as defined in ISO 4287, by means of a flowchart.

Geometrical product specifications (GPS) — Surface texture: Profile method — Flowchart for PSm, RSm, WSm and Pc, Rc, Wc

GSO ISO 22081:2022 产品几何规格（GPS） 几何公差 一般几何规格和一般尺寸规格

This document gives rules for definition and interpretation of general geometrical specifications and general size specifications defined according to ISO 8015:2011, 5.12. General specifications defined in other standards, and the link to these standards, are not covered by this document. The general geometrical specifications and general size (linear or angular) specifications defined in this document apply only to integral features (including features of size). These specifications do not apply to derived features or integral lines (see ISO 17450-1 for the definitions of integral features and derived features). Dimensions other than linear or angular sizes (see ISO 14405-2) are not covered by this document.

Geometrical product specifications (GPS) — Geometrical tolerancing — General geometrical specifications and general size specifications

22/30429469 DC BS EN ISO 4351 产品几何规格 (GPS) 协会

BS EN ISO 4351. Geometrical product specifications (GPS). Association

EN ISO 21920-3:2022 产品几何技术规范（GPS）.表面结构:轮廓.第3部分:规范

This document specifies the complete specification operator for surface texture by profile methods.

Geometrical product specifications (GPS) - Surface texture: Profile - Part 3: Specification operators (ISO 21920-3:2021)

EN ISO 21920-1:2022 产品几何技术规范（GPS）.表面结构:轮廓.第1部分:表面结构的指示

This document specifies the rules for indication of surface texture by profile methods in technical product documentation by means of graphical symbols. This document does not cover population requirements. NOTE See ISO 18391 for population (batch) specifications.

Geometrical product specifications (GPS) - Surface texture: Profile - Part 1: Indication of surface texture (ISO 21920-1:2021)

GSO ISO 14253-5:2021 产品几何规范（GPS）工件和测量设备测量检验 第5部分：指示测量仪器检定试验的不确定度

ISO 14253-5:2015 specifies concepts and terms for evaluating the uncertainties of the test values derived according to a test protocol agreed upon by the parties and relative to instrument indication(s), obtained in verification testing of GPS indicating measuring instruments. NOTE The uncertainty of the test values, referred to as test value uncertainty, is not to be confused with the measurement uncertainty associated with using that indicating measuring instrument to measure workpieces. The former only is covered in this part of ISO 14253; for guidance on the latter see the ISO/IEC Guide 98‑3 (GUM) and ISO 14253‑2. When a test of an indicating measuring instrument comprises several test values, some relative to the instrument indication and some to other metrological characteristics, this part of ISO 14253 is concerned with the uncertainty of the former only. This part of ISO 14253 does not provide guidelines to ensure the adequacy of a test protocol; rather, once a test protocol is given, it describes how to evaluate the consequent test value uncertainty.

Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 5: Uncertainty in verification testing of indicating measuring instruments

GSO ISO 14253-2:2021 产品几何规范（GPS） 工件和测量设备测量检验 第2部分：GPS测量、测量设备校准和产品验证中不确定度估计指南

ISO 14253-2:2011 gives guidance on the implementation of the concept of the "Guide to the estimation of uncertainty in measurement" (in short GUM) to be applied in industry for the calibration of (measurement) standards and measuring equipment in the field of GPS and the measurement of workpiece GPS characteristics. The aim is to promote full information on how to achieve uncertainty statements and provide the basis for international comparison of measurement results and their uncertainties (relationship between purchaser and supplier). ISO 14253-2:2011 is intended to support ISO 14253-1. Both parts are beneficial to all technical functions in a company in the interpretation of GPS specifications [i.e. tolerances of workpiece characteristics and values of maximum permissible errors (MPEs) for metrological characteristics of measuring equipment]. ISO 14253-2:2011 introduces the Procedure for Uncertainty MAnagement (PUMA), which is a practical, iterative procedure based on the GUM for estimating uncertainty of measurement without changing the basic concepts of the GUM. It is intended to be used generally for estimating uncertainty of measurement and giving statements of uncertainty for: single measurement results; the comparison of two or more measurement results; the comparison of measurement results from one or more workpieces or pieces of measurement equipment with given specifications [i.e. maximum permissible errors (MPEs) for a metrological characteristic of a measurement instrument or measurement standard, and tolerance limits for a workpiece characteristic, etc.], for proving conformance or non-conformance with the specification. The iterative method is based basically on an upper bound strategy, i.e. overestimation of the uncertainty at all levels, but the iterations control the amount of overestimation. Intentional overestimation and not underestimation, is necessary to prevent wrong decisions based on measurement results. The amount of overestimation is controlled by economical evaluation of the situation. The iterative method is a tool to maximize profit and minimize cost in the metrological activities of a company. The iterative method/procedure is economically self-adjusting and is also a tool to change/reduce existing uncertainty in measurement with the aim of reducing cost in metrology (manufacture). The iterative method makes it possible to compromise between risk, effort and cost in uncertainty estimation and budgeting.

Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification

GSO ISO 14253-1:2021 产品几何规范（GPS） 工件和测量设备的测量检验 第1部分：验证符合或不符合规范的判定规则

ISO 14253-1:2017 establishes the rules for verifying the conformity or nonconformity with a given tolerance for a characteristic of a workpiece (or a population of workpieces) or with a given maximum permissible errors for a metrological characteristic of a measuring equipment, including when the measured value falls close to the specification limits, taking measurement uncertainty into account. ISO 14253-1:2017 applies to specifications defined in general GPS standards (see ISO 14638), i.e. standards prepared by ISO/TC 213, including: - workpiece specifications and population specifications (usually given as an upper specification limit or a lower specification limit or both); - measuring equipment specifications (usually given as maximum permissible errors). ISO 14253-1:2017 only applies for characteristics and maximum permissible errors expressed as quantity values.

Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications

GSO ISO 18391:2021 产品几何规格 (GPS) 人口规格

ISO 18391:2016 defines rules to establish and to indicate population specifications, which are used to specify conditions on population characteristics, which are established from a set of characteristic values obtained one on each workpiece of a population of workpieces. A population specification (as applied to a population of workpieces considered as a collection and not as individual items) can be seen as a complementary requirement to the individual specification (as applied to each workpiece considered as individual items). Population specifications express the statistical hypotheses used on the population of workpieces. NOTE 1 A population specification is a complement to an individual GPS specification. NOTE 2 ISO 18391:2016 is not intended to mandate a given tolerancing method or how to calculate tolerance values. Its intent is to specify tools to allow the expression of population specifications.

Geometrical product specifications (GPS) — Population specification

GSO ISO 17450-3:2021 产品几何规范 (GPS) 一般概念 第3部分：公差特征

ISO 17450-3:2016 gives default definitions for the extracted features (integral or derived) of workpieces, which are toleranced features in GPS specifications (dimensional, geometrical, or surface texture specifications). This part of ISO 17450 defines default geometrical features used to define GPS characteristics.

Geometrical product specifications (GPS) — General concepts — Part 3: Toleranced features

GSO ISO 17450-4:2021 产品几何规范 (GPS) 基本概念 第4部分：量化 GPS 偏差的几何特征

ISO 17450-4:2017 specifies general rules for quantifying GPS deviations for individual GPS characteristics. NOTE GPS deviations can be local or global. A GPS characteristic defined from local GPS deviations is a parameter that transforms the set of local deviations into a global characteristic using a quantifying function (for more details, see Table 1).

Geometrical product specifications (GPS) — Basic concepts — Part 4: Geometrical characteristics for quantifying GPS deviations

GSO ISO 14638:2021 产品几何规格 (GPS) 矩阵模型

ISO 14638:2014 is a fundamental ISO GPS standard. It explains the concept of Geometrical Product Specification (ISO GPS), and provides a framework to illustrate how current and future ISO GPS standards address the requirements of the ISO GPS system. The framework is intended to be of use to users of ISO GPS standards, by illustrating the extent of the scope of the different standards, and showing how they relate to each other. The framework is also used for structuring the development of standards for GPS by technical committee ISO/TC 213.

Geometrical product specifications (GPS) — Matrix model

GSO ISO 17450-2:2021 产品几何规范（GPS） 一般概念 第2部分：基本原理、规范、运算符、不确定性和模糊性

1 Scope This part of ISO 17450 defines terms related to specifications, operators (and operations) and uncertainties used in geometrical product specifications (GPS) standards. It presents the basic tenets of the GPS philosophy while discussing the impact of uncertainty on those tenets, and examines the processes of specification and verification as they apply to GPS.

Geometrical product specifications (GPS) — General concepts — Part 2: Basic tenets, specifications, operators, uncertainties and ambiguities

GSO ISO/TS 21619:2021 产品几何规格 (GPS) 带 GPS 的文档类型

ISO/TS 21619:2018 specifies the basic types of documents with geometrical product specifications (GPS), their relationship and their related terms and definitions.

Geometrical product specifications (GPS) — Types of documents with GPS

GSO ISO 20170:2021 产品几何规格（GPS） 用于制造控制的几何特征分解

This document describes principles and tools to control a manufacturing process in accordance with a GPS specification. For this purpose a set of one or more complementary, independent characteristics (size, form, orientation, and location characteristics independent to each other) that correlate to the manufacturing process parameters and to the manufacturing process coordinate system established from the manufacturing datum system are used. This document describes the concept of decomposition of the macro-geometrical part of the GPS specification. It does not cover the micro-geometry, i.e. surface texture. The objective of the decomposition presented in this document is to define correction values for manufacturing control or to perform a statistical analysis of the process.

Geometrical product specifications (GPS) — Decomposition of geometrical characteristics for manufacturing control

EN ISO 16610-61:2015/A1:2020 产品几何技术规范(GPS).过滤. 第61部分:线性区域过滤器.高斯过滤器 包含修改件A1,2020

Geometrical product specification (GPS) - Filtration - Part 61: Linear areal filters - Gaussian filters - Amendment 1 (ISO 16610-61:2015/Amd 1:2019)

DIN 2241:2018 产品几何量技术规范(GPS).ISO米制螺纹测量仪器用螺纹量规.直径1mm～100mm标称螺纹直径的定位塞规和定位环规

This standard applies to thread setting gauges is used to set the measuring instruments for ISO metric screw threads with mechanical probing able to measure either pitch diameter or Pairing pitch Diameter depending on the Profile of the measuring elements. Thi Standard applies to all tolerances according to DIN ISO 965-1

Geometrical product specifications (GPS) - Thread setting gauges for measuring instruments for ISO metric screw threads; setting plug gauges and setting ring gauges from 1 mm to 100 mm nominal thread diameter