17.060 体积、质量、密度和粘度的测量 标准查询与下载

ASTM D7109-20 用欧洲柴油喷射装置在30次和90次循环下测定含聚合物液体剪切稳定性的标准试验方法

Standard Test Method for Shear Stability of Polymer-Containing Fluids Using a European Diesel Injector Apparatus at 30 Cycles and 90 Cycles

ASTM E2510-20 扭矩校准或流变仪一致性的标准测试方法

1.1 This test method describes the calibration or performance conformance for the torque signal generated by commercial or custom-built rheometers. The specific range of the test depends upon the torque range of the rheometer. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Torque Calibration or Conformance of Rheometers

ASTM D2196-20 用旋转（布鲁克菲尔德型）粘度计测定非牛顿材料流变性能的标准试验方法

1.1 These test methods cover the determination of the apparent viscosity and the shear thinning and thixotropic properties of non-Newtonian materials in the shear rate range from 0.1 s−1 to 50 s−1 using a rotational viscometer operating in a fluid contained in a 600 mL low form Griffin beaker. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer

ASTM D7279-20 用自动Houillon粘度计测定透明和不透明液体运动粘度的标准试验方法

1.1 This test method covers the measurement of the kinematic viscosity of transparent and opaque liquids; such as base oils, formulated oils, diesel oil, biodiesel, biodiesel blends, residual fuel oils, marine fuels, and used lubricating oils using a Houillon viscometer in automated mode. 1.2 The range of kinematic viscosity capable of being measured by this test method is from 2 mm2 /s to 2500 mm2 /s (see Fig. 1). The range is dependent on the tube constant utilized. The temperature range that the apparatus is capable of achieving is between 20 °C and 150 °C, inclusive. However, the precision has only been determined for the viscosity range; 2 mm2 /s to 478 mm2 /s at 40 °C for base oils, formulated oils, diesel oil, biodiesel, and biodiesel blends; 3 mm2 /s to 106 mm2 /s at 100 °C for base oils and formulated oils; 25 mm2 /s to 150 mm2 /s at 40 °C and 5 mm2 /s to 16 mm2 /s at 100 °C for used lubricating oils; 25 mm2 /s to 2500 mm2 /s at 50 °C and 6 mm2 /s to 110 mm2 /s at 100 °C for residual fuels. As indicated for the materials listed in the precision section. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids by Automated Houillon Viscometer

KS B 50049-1-2019 饮用冷水计量用水表第1部分:计量和技术要求

Water meters intended for the metering of cold potable water — Part 1: Metrological and technical requirements

KS B 50049-2-2019 意水表用于饮用冷水计量 第2部分:试验方法

Water meters intended for the metering of cold potable water — Part 2: Test methods

KS B 50049-3-2019 （供饮用冷水第3部分: 检测报告格式的计量水表

Water meters intended for the metering of cold potable water — Part 3: Test report format

KS B 5293-2019 皮带秤

Belt weighers

KS B 50076-2-2019 非自动衡器 第2部分：试验报告格式

Non-automatic weighing instruments — Part 2: Test report format

KS B 5332-2019 螺旋仪

Spiro meter

KS B 50076-1-2019 非自动衡器 第1部分：计量技术要求 试验

Non-automatic weighing instruments — Part 1: Metrological and technical requirements — Tests

ASTM D7042-19 Stabinger粘度计的动态粘度和液体密度的标准测试方法（和运动粘度的计算）

Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)

ASTM D445-19a 透明和不透明液体的运动粘度的标准测试方法（和动态粘度的计算）

Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

ASTM D7042-19e1 Stabinger粘度计的动态粘度和液体密度的标准测试方法（和运动粘度的计算）

Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)

ASTM D6022-19 永久剪切稳定性指标计算标准实践

1.1 This practice specifies the procedure for the calculation of Permanent Shear Stability Index (PSSI) of an additive using viscosities before and after a shearing procedure. 1.2 PSSI is calculated for a single blend component and can then be used to estimate the effects of that component on finished lubricant blends. 1.3 This practice is applicable to many products and may use data from many different test methods. The calculation is presented in its most general form in order not to restrict its use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Calculation of Permanent Shear Stability Index

T/SZMS 0001-2019 智能溯源电子秤

        本标准规定了智能追溯电子秤产品的计量要求、技术要求、智能化要求、试验方法、检验规则及标志、电磁兼容、通讯、包装、运输、贮存。 本标准适用于称重传感器为一次转换元件并带有载荷承载器、电子装置、数字显示、网络通信的中准确度等级的自行指示式电子台案秤。

Intelligent Traceability Electronic Sacle

ASTM C693-93(2019) 浮力密度玻璃的标准试验方法

1.1 This test method covers the determination of the density of glasses at or near 25 °C, by buoyancy. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Density of Glass by Buoyancy

ASTM D445-19 透明和不透明液体的运动粘度的标准测试方法（和动态粘度的计算）

Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

ASTM D6910/D6910M-19 建筑泥浆沼泽漏斗粘度的标准试验方法

1.1 This test method provides an indirect measurement of the viscosity of construction slurries using a funnel (Marsh Funnel) and a graduated cup with specific volume marks. This test method provides an indicator of the viscosity on a routine basis. This test method has been modified from the API Recommended Practice 13B-1. 1.2 The result determined using the method is referred to as the Marsh Funnel Viscosity. The Marsh Funnel Viscosity is an index property and is not an actual measurement of viscosity. 1.3 This test can be performed in the laboratory or in the field to assess the Marsh Funnel Viscosity of a slurry for quality control purposes. 1.4 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Marsh Funnel Viscosity of Construction Slurries

ASTM D88/D88M-07(2019)e1 Saybolt粘度的标准测试方法

1.1 This test method covers the empirical procedures for determining the Saybolt Universal or Saybolt Furol viscosities of petroleum products at specified temperatures between 21 and 99°C [70 and 210°F]. A special procedure for waxy products is indicated. NOTE 1—Test Methods D445 and D2170/D2170M are preferred for the determination of kinematic viscosity. They require smaller samples and less time, and provide greater accuracy. Kinematic viscosities may be converted to Saybolt viscosities by use of the tables in Practice D2161. It is recommended that viscosity indexes be calculated from kinematic rather than Saybolt viscosities. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Saybolt Viscosity