17.140.20 机器和设备的噪声 标准查询与下载

LST EN ISO 5135:2002 声学 通过在混响室中测量来确定空气末端装置、空气末端装置、阻尼器和阀门噪声的声功率级（ISO 5135:1997）

Acoustics - Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room (ISO 5135:1997)

LST EN 27574-1-2002 声学 确定和验证机械和设备规定噪声排放值的统计方法 第1部分：一般考虑和定义（ISO 7574-1:1985）

Acoustics - Statistical methods for determining and verifying stated noise emission values of machinery and equipment - Part 1: General considerations and definitions (ISO 7574-1:1985)

LST EN 27574-2-2002 声学 确定和验证机械和设备规定噪声排放值的统计方法 第2部分：单个机器规定值的方法（ISO 7574-2:1985）

Acoustics - Statistical methods for determining and verifying stated noise emission values of machinery and equipment - Part 2: Methods for stated values for individual machines (ISO 7574-2:1985)

LST EN 27574-3-2002 声学 确定和验证机械和设备规定噪声排放值的统计方法 第3部分：机器批次规定值的简单（过渡）方法（ISO 7574-3:1985）

Acoustics - Statistical methods for determining and verifying stated noise emission values of machinery and equipment - Part 3: Simple (transition) method for stated values for batches of machines (ISO 7574-3:1985)

LST EN 27574-4-2002 声学 确定和验证机械和设备规定噪声排放值的统计方法 第4部分：机器批次规定值的方法（ISO 7574-4:1985）

Acoustics - Statistical methods for determining and verifying stated noise emission values of machinery and equipment - Part 4: Methods for stated values for batches of machines (ISO 7574-4:1985)

LST EN ISO 3822-4:2002 声学 供水装置中使用的器具和设备噪声排放的实验室测试 第4部分：专用器具的安装和操作条件

Acoustics - Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 4: Mounting and operating conditions for special appliances

KS C IEC 60034-9:2002 旋转电机.第9部分:噪声限值

IEC 60034의 이 부분은 IEC 60034-6에 따르는 냉각법과 IEC 60034-5

Rotating electrical machines－Part 9：Noise limits

ANSI/ASA S12.50-2002 声学.噪声源声功率级的测定.基本标准的使用指南

Gives guidance for the use of a series of 9 International Standards describing various methods for determining sound power levels from all types of machinery and equipment. Provides: brief summaries of these basic International Standards; guidance on selection of one or more of these standards. Applies only to airborne sound. For use in preparation of noise test codes (ISO 12001) and noise testing where no specific noise test code exists.

Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards

GOST 23941-2002 机器噪声.噪声特性测量方法.一般要求

Noise of machines. Methods for determination of noise characteristics. General requirements

LST EN 61063-2001 声学 汽轮机和被驱动机械发出的空气噪声的测量（IEC 61063:1991）

Acoustics. Measurement of airborne noise emitted by steam turbines and driven machinery (IEC 61063:1991)

BS ISO 15664:2001 声学.露天设备噪声控制设计规程

This International Standard defines the procedures for noise control of mainly open plants. It is applicable to the following: — specification of procedures for noise control during engineering of a new plant and modification/extension of existing plants (construction noise procedures are outside the scope of this International Standard but should be considered); — definition of responsibilities of parties involved, viz. "end-user", "engineering contractor" and "equipment supplier"; — description of general procedures to arrive at noise requirements for individual equipment, on the basis of overall noise requirements for the plant. A schematic flowchart, reviewing the noise control process, is presented in annex A and a summary of action items is presented in annex B. NOTE Concerning specific engineering methods for the acoustic design and analysis of plants, use should be made of other standards and textbooks.

Acoustics - Noise control design procedures for open plant

NF S30-006:2001 声学.噪声源声强级的测定.基础标准用指南

Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards.

ISO 15664:2001 声学 开放式工厂的噪声控制设计规程

This International Standard defines the procedures for noise control of mainly open plants. It is applicable to the following: — specification of procedures for noise control during engineering of a new plant and modification/extension of existing plants (construction noise procedures are outside the scope of this International Standard but should be considered); — definition of responsibilities of parties involved, viz. "end-user", "engineering contractor" and "equipment supplier"; — description of general procedures to arrive at noise requirements for individual equipment, on the basis of overall noise requirements for the plant. A schematic flowchart, reviewing the noise control process, is presented in annex A and a summary of action items is presented in annex B. NOTE Concerning specific engineering methods for the acoustic design and analysis of plants, use should be made of other standards and textbooks.

Acoustics - Noise control design procedures for open plant

DIN EN ISO 3740:2001 声学.噪声源声功率级测定.基础标准使用指南

The document introduces a series of mine basic international standards describing various methods for determining the sound levels power from all types of machinery and equipment. It provides brief summaries of these basic International Standard ; guidance on the selection of one or more of these standards which are appropriate to any particular type of machinery. The guidance given applies only to airborne sound. It is for use in the preparation of noise test codes for specific machines and also in noise testing where no relevant test code exists. The following terms are defined: emission, sound power, sound power level, sound pressure level, time-averaged sound pressure level, sound energy level, single-event sound pressure level, sound intensity, background noise, background noise level, background noise correction, environmental correction.#,,#

Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards (ISO 3740:2000); German version EN ISO 3740:2000

BS EN ISO 3740:2001 声学.噪声源的声压级的测定.基础标准使用导则

This International Standard gives guidance for the use of a series of nine International Standards describing various methods for determining the sound power levels from all types of machinery and equipment. It provides: — brief summaries of these basic International Standards; — guidance on the selection of one or more of these standards which are appropriate to any particular type (see clause 5 and annex D). The guidance given applies only to airborne sound. It is for use in the preparation of noise test codes (see ISO 12001) and also in noise testing where no specific noise test code exists. This International Standard is not intended to replace any of the details of, or add any additional requirements to, the individual test methods in the other basic standards referred to. These basic standards specify the acoustical requirements for measurements appropriate for different test environments and accuracies. It is important that specific test codes for various types of machinery and equipment be established and used in accordance with the requirements of these basic International Standards. Such standardized noise test codes will recommend the basic International Standard(s) to be used and will give detailed requirements on mounting and operating conditions for a particular family to which the machine under test belongs. If no specific noise test code exists for a particular type of machinery, this International Standard is of use for the choice of the most suitable of the basic standards. In all cases, the mounting and operating conditions of the machine under test should be in accordance with the general principles given in the basic standards. NOTE Two quantities which complement each other can be used to describe the sound emission of machinery or equipment. One is the emission sound pressure level at a specified position and the other is the sound power level. The International Standards which describe the basic methods for determining emission sound pressure levels at the work station and at other specified positions are the series ISO 11200 to ISO 11204.

Acoustics - Determination of sound power levels of noise sources - Guidelines for the use of basic standards

GOST 30691-2001 机器噪音.噪音排放值的公布和确认

Настоящий стандарт распространяется на машины и оборудование, являющиеся источниками шума в воздушной среде. Стандарт устанавливает: - тр

Noise of machines. Declaration and verification of noise emission values

GOST 30720-2001 机器噪音.在工作站和其它规定位置上声功率级的排放声压级的测定

Настоящий стандарт распространяется на стационарные и передвигающиеся машины и оборудование, эксплуатируемые внутри или вне производст

Noise of machines. Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level

ISO 3740:2000 声学 噪声源声功率级的测定 基本标准使用导则

This International Standard gives guidance for the use of a series of nine International Standards describing various methods for determining the sound power levels from all types of machinery and equipment. It provides: — brief summaries of these basic International Standards; — guidance on the selection of one or more of these standards which are appropriate to any particular type (see clause 5 and annex D). The guidance given applies only to airborne sound. It is for use in the preparation of noise test codes (see ISO 12001) and also in noise testing where no specific noise test code exists. This International Standard is not intended to replace any of the details of, or add any additional requirements to, the individual test methods in the other basic standards referred to. These basic standards specify the acoustical requirements for measurements appropriate for different test environments and accuracies. It is important that specific test codes for various types of machinery and equipment be established and used in accordance with the requirements of these basic International Standards. Such standardized noise test codes will recommend the basic International Standard(s) to be used and will give detailed requirements on mounting and operating conditions for a particular family to which the machine under test belongs. If no specific noise test code exists for a particular type of machinery, this International Standard is of use for the choice of the most suitable of the basic standards. In all cases, the mounting and operating conditions of the machine under test should be in accordance with the general principles given in the basic standards. NOTE Two quantities which complement each other can be used to describe the sound emission of machinery or equipment. One is the emission sound pressure level at a specified position and the other is the sound power level. The International Standards which describe the basic methods for determining emission sound pressure levels at the work station and at other specified positions are the series ISO 11200 to ISO 11204.

Acoustics - Determination of sound power levels of noise sources - Guidelines for the use basic standards

DIN ISO 8297:2000 声学.环境中声压级评定用多声源工业厂房声功率级的测定.工程法

The document specifies an engineering method for determining the sound power level of multi-source industrial plants which is relevant to the assessment of the noise they contribute to points in the environment around the plant. It is based in measuring the sound pressure level on a closed path (measurement contour) surrounding the plant and determining an appropriate measurement surface.

Acoustics - Determination of sound power levels of multisource industrial plants for evaluation of sound pressure levels in the environment - Engineering method (ISO 8297:1994)

JIS Z 8737-1:2000 声学.机械装置及设备发出的噪声.工作地点和其它特定场所发出声压级的测量.反射平面上基本自由声波场的工程测量法

この規格は，反射面上の準自由音場において，機械及び装置近傍の作業位置及び他の指定位置における放射音圧レべルを測定するーつの方法について規定する。

Acoustics -- Noise emitted by machinery and equipment -- Measurement of emission sound pressure levels at a work station and at other specified positions -- Engineering method in an essentially free field over a reflecting plane