17.160 振动、冲击和振动测量 标准查询与下载

ISO 6070:2019 振动发生器辅助表 - 描述设备特性的方法

This document establishes requirements to ensure appropriate exchange of information between manufacturers and users of auxiliary tables with a view to working out related specifications and possibly to comparing, in an objective way, the characteristics supplied by the manufacturers of auxiliary tables and associated guidance systems. This document is applicable to auxiliary tables which include slip tables and head expanders. It does not cover auxiliary tables with several degrees of freedom. This document provides three levels of description of the test equipment, as follows: a) minimum level; b) medium level; c) high level. This document gives a list of characteristics to be specified for each level of description.

Auxiliary tables for vibration generators — Methods of describing equipment characteristics

T/CSEB 0008-2019 爆破振动监测技术规范

本标准规定了爆破振动监测的基本原则、监测设计、现场监测、数据处理与分析、报告编制、仪器要求、仪器的标定与校准等内容。 本标准适用于各种民用爆破工程第三方振动监测工作，其他振动监测工作可参照执行。

Technical specification for monitoring of blasting vibration

BS ISO 10813-2:2019 振动发生机 选择指南 动态结构测试设备

What is ISO 10813‑2 - Vibration-generating machines selection guidance about?   A proper selection of vibration generating system, when purchasing new test equipment or updating existing equipment for the purposes of a specific test or when choosing between the equipment proposed by a test laboratory or even selecting a laboratory which offers its service to carry out such a test, is very important.   ISO 10813 series provides you guidance for with selection of vibration-generating machines. ISO 10813-2 focuses on the equipment for dynamic structural testing . ISO 10813‑2 deals only with translational excitation. For equipment applied to generate angular vibration.

Vibration-generating machines. Guidance for selection - Equipment for dynamic structural testing

ISO 10813-2:2019 振动发生机选择指南第2部分:动态结构试验设备

This document provides guidance to select a vibration generator that will be used to evaluate frequency responses of a test structure or to study how vibration grows/decreases along the structure. These structural dynamics tests can be carried out under field or laboratory conditions (see the ISO 7626 or This document describes the selection procedure in terms of the force developed by a single vibration generator. Meanwhile, to move massive structures such as dams or bridges, an assembly of vibration generators is usually applied. Properly phased generators produce in total the same force as calculated for a single vibration generator (see 6.2.6). Guidance also can be applied for the selection of equipment to be used for modal testing to determine natural frequencies, modal shapes and damping in a structure; however, for such a test, more factors than covered by this document usually need to be considered. This document deals only with translational excitation. For equipment applied to generate angular vibration, see Reference [8].

Vibration-generating machines — Guidance for selection — Part 2: Equipment for dynamic structural testing

ASTM E3213-19 通过金属和非金属零件的扫频正弦输入进行过程补偿共振试验的零件对自身检验的标准实施规程

1.1 This practice covers a general procedure for using the Process Compensated Resonance Testing (PCRT) via swept sine input method to perform Part-to-Itself (PTI) examination on populations of newly manufactured and in-service parts. PCRT detects resonance pattern differences in metallic and non-metallic parts. Practice E2534 for Defect Detection with PCRT and Practice E3081 for Outlier Screening with PCRT cover the development and application of PCRT sorting modules that inspect a part at a single point in time. These methods use the resonance frequency spectra recorded from test parts and perform different statistical analyses to compare test parts to reference populations. These comparisons include, and must compensate for, the normal geometric, material, and processing variations present in any population of parts. In many applications, however, the user may need to evaluate the effects of a single processing step or in-service load in isolation from other sources of variation. For example, a manufacturer may want to perform process monitoring and control on a heat treatment or hardening process. A maintainer may want to evaluate the effect of service cycles in an engine. A PCRT PTI examination measures the resonance frequency spectrum of a part at two points in time, such as before and after a manufacturing process step, and calculates the change in resonance frequencies to evaluate the effect of the intervening process. Control limits can be set on the frequency change to field a PTI PASS/FAIL inspection capability. The limits may be based on training populations of parts with acceptable and unacceptable levels of change, model predictions of the effects of part changes, or criteria derived from process control practices. Manufacturing processes and in-service loads that can be evaluated with a PCRT PTI inspection include, but are not limited to heat treatment, hot isostatic pressing (HIP), shot peening, induction hardening, carburization, coating, thermal history changes, residual stress changes, creep, plastic deformation, corrosion, and fatigue. This practice is intended for use with instruments capable of exciting, measuring, recording, and analyzing multiple, whole body, mechanical vibration resonance frequencies in acoustic or ultrasonic frequency ranges, or both. 1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Part-to-Itself Examination Using Process Compensated Resonance Testing Via Swept Sine Input for Metallic and Non-Metallic Parts

BS ISO 18434-2:2019 机器系统的状态监测和诊断 热成像 图像解释和诊断

What is ISO 18434-2 - Thermography about? ISO 18434-2 is the second part of the ISO 18434 series that discusses condition monitoring and diagnostics of machine systems. ISO 18434-2 provides specific guidance on the interpretation of infrared thermograms as part of a programme for condition monitoring and diagnostics of machine systems. Who is ISO 18434-2 - Thermography f or? ISO 18434-2 on Image interpretation and diagnostics is beneficial for: Condition monitoring engineers Radiologists Infrared thermographer and thermologists Why should you use ISO 18434-2 - Thermography ? Thermography can be used to identify and document anomalies for the purposes of condition monitoring of machines. These anomalies are usually caused by such mechanisms as operation, improper lubrication, misalignment, worn components or mechanical loading anomalies.

Condition monitoring and diagnostics of machine systems. Thermography - Image interpretation and diagnostics

ISO 18434-2:2019 机器系统的状态监测和诊断.热成像.第2部分:图像解释和诊断

This document provides specific guidance on the interpretation of infrared thermograms as part of a programme for condition monitoring and diagnostics of machine systems. In addition, IR applications pertaining to machinery performance are addressed. This document is intended to: — provide guidance on establishing severity assessment criteria for anomalies identified by IRT; — outline methods and requirements for carrying out thermography of machine systems, including safety recommendations; — provide information on image interpretation, assessment criteria and reporting requirements.

Condition monitoring and diagnostics of machine systems — Thermography — Part 2: Image interpretation and diagnostics

ASTM D7400/D7400M-19 井下地震试验标准试验方法

1.1 These test methods address compression (P) and shear (S) waves propagating in the downward direction in a nearly vertical plane. The seismic waves can be denoted as PV or PZ for a downward propagating compression wave and as SVH or SZX for downward propagating and horizontally polarized shear wave. The SVH or SZX is also referred to as an SH wave. These test methods are limited to the determination of the interval velocities from arrival times and relative arrival times of compression (P) waves and vertically (SV) and horizontally (SH) oriented shear (S) seismic waves which are generated near surface and travel down to an array of vertically installed seismic sensors. Two methods are discussed, which include using either one or two downhole sensors (receivers). 1.2 Various applications of the data will be addressed and acceptable procedures and equipment, such as seismic sources, receivers, and recording systems will be discussed. Other items addressed include source-to-receiver spacing, drilling, casing, grouting, a procedure for borehole installation, and conducting actual borehole and seismic cone tests. Data reduction and interpretation is limited to the identification of various seismic wave types, apparent velocity relation to true velocity, example computations, use of Snell’s law of refraction, and assumptions. 1.3 There are several acceptable devices that can be used to generate a high-quality P or SV source wave or both and SH source waves. Several types of commercially available receivers and recording systems can also be used to conduct an acceptable downhole survey. Special consideration should be given to the types of receivers used and their configuration to provide an output that accurately reflects the input motion. These test methods primarily concern the actual test procedure, data interpretation, and specifications for equipment which will yield uniform test results. 1.4 All recorded and calculated values shall conform to the guide for significant digits and rounding established in Practice D6026. 1.4.1 The procedures used to specify how data are collected/ recorded and calculated in these test methods are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of these test methods to consider significant digits used in analysis methods for engineering design. 1.4.2 Measurements made to more significant digits or better sensitivity than specified in these test methods shall not be regarded a nonconformance with this standard. 1.5 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5.1 The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F = ma) calculations are involved. 1.5.2 It is common practice in the engineering/construction profession to concurrently use pounds to represent both a unit of mass (lbm) and of force (lbf). This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. As stated, this standard includes the gravitational system of inch-pound units and does not use/present the slug unit for mass. However, the use of balances or scales recording pounds of mass (lbm) or recording density in lbm/ft3 shall not be regarded as nonconformance with this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1 This test method is under the jurisdiction of ASTM Committee D18 on Soil and Rock and is the direct responsibility of Subcommittee D18.09 on Cyclic and Dynamic Properties of Soils. Current edition approved Feb. 1, 2019. Published February 2019. Originally approved in 2007. Last previous edition approved in 2017 as D7400 – 17. DOI: 10.1520/D7400_D7400M-19. *A Summary of Changes section appears at the end of this standard Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Downhole Seismic Testing

DIN ISO 20816-8:2018 机械振动 机器振动的测量和评估 第8部分：往复式压缩机系统（ISO 20816-8:2018）

The document provides specific guidance for the evaluation of vibration measured on the bearing housings of reciprocating compressor systems and gives limit values for different measurement positions. Additionally, an annex covers vibration of small bore connection (SBC) piping.

Mechanical vibration - Measurement and evaluation of machine vibration - Part 8: Reciprocating compressor systems (ISO 20816-8:2018)

BS ISO 16063-44:2018 振动和冲击传感器的校准方法 现场振动校准器的校准

What is ISO 16063-44 - FVC c alibration about?   ISO 16063-44 is a safety standard on the calibration of field vibration calibrators. Since vibration calibrators are used for testing and checking vibration sensors and measuring instruments at the site of their operation, they are transportable and battery operated.    ISO 16063-44 specifies the instrumentation and procedure to be used for performing calibration of field vibration calibrators (FVCs). Calibration intervals are determined based on periodic examinations of the operational condition of the FVC.   NOTE:  ISO 16063-44 is not applicable to FVCs used for the calibration of transduc...

Methods for the calibration of vibration and shock transducers - Calibration of field vibration calibrators

KS B ISO 16063-12-2018 振动和冲击传感器的校准方法 - 第12部分:通过互易方法的主要振动校准

Methods for the calibration of vibration and shock transducers — Part 12: Primary vibration calibration by the reciprocity method

KS B ISO 8568-2018 机械冲击 - 试验机 - 特性和性能

Mechanical shock — Testing machines — Characteristics and performance

KS B ISO 16063-22:2018 振动和冲击传感器的校准方法第22部分:与参考传感器比较的冲击校准

Methods for the calibration of vibration and shock transducers — Part 22: Shock calibration by comparison to a reference transducer

KS B ISO 18437-3:2018 机械振动和冲击 - 粘弹性材料的动态力学性能表征 - 第3部分:悬臂剪切梁法

Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 3: Cantilever shear beam method

KS B ISO 18431-2-2018 机械振动和冲击 - 信号处理 - 第2部分:傅里叶变换分析的时域窗口

Mechanical vibration and shock — Signal processing — Part 2: Time domain windows for Fourier Transform analysis

KS B ISO 16063-21-2018 振动和冲击传感器的校准方法 - 第21部分:与参考传感器比较的振动校准

Methods for the calibration of vibration and shock transducers — Part 21: Vibration calibration by comparison to a reference transducer

KS B ISO 16063-11:2018 振动和冲击传感器校准方法第11部分:激光干涉测量一次振动校准

Methods for the calibration of vibration and shock transducers — Part 11: Primary vibration calibration by laser interferometry

KS B ISO 18437-2:2018 机械振动和冲击 - 粘弹性材料动态力学性能的表征 - 第2部分:共振法

Mechanical vibration and shock — Characterization of the dynamic mechanical properties of visco-elastic materials — Part 2: Resonance method

KS B ISO 8042:2018 震动和振动测量 - 为地震提供指定的特性

Shock and vibration measurements — Characteristics to be specified for seismic pick-ups

KS B ISO 16063-13-2018 振动和冲击传感器的校准方法第13部分:使用激光干涉测量的主要冲击校准

Methods for the calibration of vibration and shock transducers — Part 13: Primary shock calibration using laser interferometry