17.160 振动、冲击和振动测量 标准查询与下载

KS B ISO 13373-3-2018 机器状态监测和诊断 - 振动状态监测 - 第3部分:振动诊断指南

Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 3:Guidelines for vibration diagnosis)

KS B ISO 13373-3:2018 机器状态监测和诊断 - 振动状态监测 - 第3部分:振动诊断指南

Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 3:Guidelines for vibration diagnosis)

KS B ISO 16064-41-2018 振动和冲击传感器的校准方法 - 第41部分:激光振动计的校准

Methods for the calibration of vibration and shock transducers — Part 41:Calibration of laser vibrometers

KS B ISO 20816-1-2018 机械振动 - 机械振动的测量和评估 - 第1部分:一般准则

Mechanical vibration — Measurement and evaluation of machine vibration — Part 1:General guidelines

KS B ISO 16063-17-2018 振动和冲击传感器的校准方法 - 第17部分:离心机初步校准

Methods for the calibration of vibration and shock transducers — Part 17:Primary calibration by centrifuge

KS B ISO 20816-1:2018 机械振动 - 机械振动的测量和评估 - 第1部分:一般准则

Mechanical vibration — Measurement and evaluation of machine vibration — Part 1:General guidelines

KS B ISO 16063-32-2018 振动和冲击传感器校准方法 - 第32部分:共振测试 - 通过冲击激励测试加速度计的频率和相位响应

Methods for the calibration of vibration and shock transducers — Part 32:Resonance testing — Testing the frequency and the phase response of accelerometers by means of shock excitation

KS B ISO 16064-41:2018 振动和冲击传感器的校准方法 - 第41部分:激光振动计的校准

Methods for the calibration of vibration and shock transducers — Part 41:Calibration of laser vibrometers

KS B ISO 16063-17:2018 振动和冲击传感器的校准方法 - 第17部分:离心机初步校准

Methods for the calibration of vibration and shock transducers — Part 17:Primary calibration by centrifuge

BS ISO 29821:2018 机器的状态监测和诊断 超声波 一般准则、程序和验证

1   Scope This document — gives guidelines for establishing severity assessment criteria for anomalies identified by airborne (AB) and structure-borne (SB) ultrasound, — specifies methods and requirements for carrying out ultrasonic examination of machines, including safety recommendations and sources of error, and — provides information relative to data interpretation, assessment criteria and reporting.

Condition monitoring and diagnostics of machines. Ultrasound. General guidelines, procedures and validation

BS ISO 17359:2018 机器的状态监测和诊断 一般准则

1   Scope This document gives guidelines for the general procedures to be considered when setting up a condition monitoring programme for machines and includes references to associated standards required in this process. This document is applicable to all machines.

Condition monitoring and diagnostics of machines. General guidelines

ISO 21984:2018 船舶和海洋技术 - 关于特定船舶可居住性振动的测量 评估和报告指南

This document gives guidelines for the measurement, evaluation and reporting of vibration with regard to habitability for all persons on board ships satisfying one or both of the following conditions: a) 2-stroke cycle, long-stroke, low-speed diesel engine directly coupled to the fixed-pitch propulsion propeller is installed. b) length of deck house (L) is limited as compared with its height (H) (i.e. deck house of around 1,0 and above in slenderness ratio of H to L). An example of length of deck house (L) and its height (H) for slenderness ratio is shown in Annex A. Overall frequency-weighted r.m.s. vibration values in the frequency range 1 Hz to 80 Hz are given as guidance values for different spaces on ships. This document is applicable to specific ships with intended voyages of 24 h or more. This document specifies requirements for the instrumentation and the procedure of measurement in normally occupied spaces. It also contains analysis specifications and guidelines for the evaluation of ship vibration with respect to habitability. This document is not applicable to machinery spaces, other than engine control rooms, where persons do not stay for prolonged periods of time. reporting of vibration with regard to habitability for all persons on board passenger and merchant ships, including specific ships to which this document may also be applicable can be found in ISO 20283-5. This document is neither complementary nor additional but supplementary to ISO 20283-5. The shipbuilder can select either this document or ISO 20283-5 to apply to any specific ship upon due consideration to individual design conditions of the ship and, if any, experience in building sister or similar ships, and that particular selection is intended to be agreed on by the shipowner. The evaluation of low-frequency ship motion which can result in motion sickness is covered by

Ships and marine technology — Guidelines for measurement, evaluation and reporting of vibration with regard to habitability on specific ships

KS B ISO 7626-2-2018 机械振动和冲击 - 机械移动性的实验测定 - 第2部分:使用单点平移激励与附加振动激励器的测量

Mechanical vibration and shock — Experimental determination of mechanical mobility — Part 2: Measurements using single-point translation excitation with an attached vibration exciter

KS B ISO 7626-2:2018 机械振动和冲击 - 机械移动性的实验测定 - 第2部分:使用单点平移激励与附加振动激励器的测量

Mechanical vibration and shock — Experimental determination of mechanical mobility — Part 2: Measurements using single-point translation excitation with an attached vibration exciter

ISO 29821:2018 机器的状态监测和诊断 超声波 一般指南、程序和验证

This document — gives guidelines for establishing severity assessment criteria for anomalies identified by airborne (AB) and structure-borne (SB) ultrasound, — specifies methods and requirements for carrying out ultrasonic examination of machines, including safety recommendations and sources of error, and — provides information relative to data interpretation, assessment criteria and reporting.

Condition monitoring and diagnostics of machines - Ultrasound - General guidelines, procedures and validation

ISO 17359:2018 机器的条件监控和诊断.总导则

This document gives guidelines for the general procedures to be considered when setting up a condition monitoring programme for machines and includes references to associated standards required in this process. This document is applicable to all machines.

Condition monitoring and diagnostics of machines - General guidelines

DIN ISO 7919-3:2018 机械振动.采用旋转轴测量机械振动的评定.第3部分:啮合连接工业机械(ISO 7919-3-2009+Amd.1-2017)

This standard provides specific guidance for assessing the severity of radial vibration measured on the shafts of coupled industrial machines with fluid-film bearings in situ. It applies to coupled industrial machines with fluid-film bearings, having maximum continuous rated speeds in the range 1000 r/min to 30000 r/min and not being limited by size and power (with certain restrictions), comprising - steam turbines and generators with outputs less than or equal to 40 MW; - steam turbines and generators with outputs greater than 40 MW and speeds other than 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (although generators seldom fall into this category); - rotary compressors; - industrial gas turbines with outputs less than or equal to 3 MW; - turbofans; - electric drives and associated gears, where relevant; - rotodynamic pumps (turbo pumps). Two criteria are provided for assessing the machine vibration when operating under steady state conditions. One criterion considers the magnitude of the observed vibration; the second considers changes in the magnitude. In addition, different criteria are provided for transient operating conditions, such as run-up and coast-down. The evaluation procedures presented in this part of ISO 7919 are based on broad-band measurements. The following are excluded from this part of ISO 7919: - steam turbines and/or generators with outputs greater than 40 MW and speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); - gas turbine sets with outputs greater than 3 MW (see ISO 7919-4 and ISO 20816-2); - machine sets in hydraulic power generating and pump-storage plants (see ISO 20816-5); - rotodynamic pumps including integrated electric motors, i.e. where the impeller is mounted directly on the motor shaft or is rigidly attached to it (see ISO 10816-7); - submerged motor-pumps; - reciprocating pumps; - rotary positive displacement compressors (e. g. screw compressors); - reciprocating compressors; - wind turbines.

Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 3: Coupled industrial machines (ISO 7919-3:2009 + Amd.1:2017)

DIN ISO 10816-4:2018 机械振动.通过固定组件测量值估测机械振动.第4部分:带流体膜轴承的燃气汽轮机组(ISO 10816-4-2009+Amd.1-2017)

This standard provides specific guidance for assessing the severity of radial vibration measured on the bearing housings of gas turbines with fluid-film bearings in situ. The criteria provided in this document apply to heavy-duty gas turbine sets used in electrical and mechanical drive applications, with outputs greater than 3 MW and a speed range under load between 3 000 r/min and 30 000 r/min. This includes gas turbines coupled to other rotating machinery either directly or through a gearbox. Two criteria are provided for assessing the machine vibration when operating under steady state conditions. One criterion considers the magnitude of the observed vibration; the second considers changes in the magnitude. In addition, different criteria are provided for transient operating conditions, such as run-up and coast-down. The evaluation procedures presented in this part of ISO 10816 are based on broad-band measurements. This part of ISO 10816 is not applicable to the following: a) aero-derivative gas turbines (including gas turbines with dynamic properties similar to those of aero-derivatives); b) gas turbines with outputs greater than 40 MW and with rated speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); c) gas turbines with outputs less than or equal to 3 MW (see ISO 10816-3); d) gas turbine driven rotodynamic pumps (see ISO 10816-7); e) coupled steam turbines and/or generators with outputs less than or equal to 40 MW (see ISO 10816-3); f) coupled steam turbines and/or generators with outputs greater than 40 MW and speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); g) coupled steam turbines and/or generators with outputs greater than 40 MW and speeds other than 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (although generators seldom fall into this category) (see ISO 10816-3); h) synchronizing clutches which couple the gas turbine to a steam turbine or generator (see ISO 20816-2); i) coupled rotary compressor

Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 4: Gas turbine sets with fluid-film bearings (ISO 10816-4:2009 + Amd.1:2017)

BS ISO 18437-6:2017 机械振动和冲击 粘弹性材料动态力学性能表征 时间-温度叠加

1   Scope This document specifies a standard method for the acquisition and analysis of data obtained using the test methods found in ISO 18437‑1 to ISO 18437‑5, ISO 6721‑4 to ISO 6721‑7 and ISO 6721‑12. It is applicable to visco-elastic materials that are thermorheologically simple and that have been tested at equilibrium state for every temperature.

Mechanical vibration and shock. Characterization of the dynamic mechanical properties of visco-elastic materials - Time-temperature superposition

KS B ISO 13373-2:2017 机器的工况监测和诊断 振动条件监测 第2部分：振动数据的处理、分析和表示

Condition monitoring and diagnostics of machines —Vibration condition monitoring — Part 2: Processing, analysis and presentation of vibration data