17.160 振动、冲击和振动测量 标准查询与下载

BS ISO 13381-1:2015 机器的状态监测和诊断 预测 一般准则

Condition monitoring and diagnostics of machines. Prognostics. General guidelines

BS ISO 13373-3:2015 机器的工况监测和诊断. 振动状态监测. 振动诊断指南

Condition monitoring and diagnostics of machines. Vibration condition monitoring. Guidelines for vibration diagnosis

GSO ISO 4866:2015 机械振动和冲击 固定结构的振动 - 测量振动和评估其对结构影响的指南

This International Standard establishes principles for carrying out vibration measurement and processing data with regard to evaluating vibration effects on structures. It does not cover the source of excitation except when the source dictates dynamic range, frequency or other relevant parameters. The evaluation of the effects of structural vibration is primarily obtained from the response of the structure, using appropriate analytical methods by which the frequency, duration and amplitude can be defined. This International Standard only deals with the measurement of structural vibration and excludes the measurement of airborne sound pressure and other pressure fluctuations, although response to such excitations is taken into consideration. This International Standard applies to all structures built above or below ground. Such structures are used or maintained and include buildings, structures of archaeological and historical value (cultural heritage), bridges and tunnels, gas and liquid installations including pipelines, earth structures (e.g. dykes and embankments), and fixed marine installations (e.g. quays and wharfs). This International Standard does not apply to some special structures, including nuclear plants and dams.The response of structures depends upon the excitation. This International Standard examines the methods of measurement as affected by the source of excitation, i.e. frequency, duration, and amplitude as induced by any source (e.g. earthquake, hurricane, explosion, wind loading, airborne noise, sonic boom, internal machinery, traffic, and construction activities).

Mechanical vibration and shock -- Vibration of fixed structures -- Guidelines for the measurement of vibrations and evaluation of their effects on structures

GSO ISO 6954:2015 机械振动 客船和商船起居室振动的测量、报告和评估指南

This International Standard contains guidelines for the evaluation of vibration with regard to habitability on a passenger or merchant ship, as well as requirements for the instrumentation and the method of measurement in normally occupied spaces. Assessment of low-frequency ship motion which may result in motion sickness is covered by other International Standards.

Mechanical vibration -- Guidelines for the measurement, reporting and evaluation of vibration with regard to habitability on passenger and merchant ships

GSO ISO 14839-3:2015 机械振动 主动磁力轴承旋转设备的振动 第3部分：稳定裕度的评定

This part of ISO 14839 establishes the stability requirements of rotating machinery equipped with active magnetic bearings (AMB). It specifies a particular index to evaluate the stability margin and delineates the measurement of this index. It is applicable to industrial rotating machines operating at nominal power greater than 15 kW, and not limited by size or operational rated speed. It covers both rigid AMB rotors and flexible AMB rotors. Small-scale rotors, such as turbo molecular pumps, spindles, etc., are not addressed. This part of ISO 14839 concerns the system stability measured during normal steady-state operation in-house and/or on-site. The in-house evaluation is an absolute requirement for shipping of the equipment, while the execution of on-site evaluation depends upon mutual agreement between the purchaser and vendor. This part of ISO 14839 does not address resonance vibration appearing when passing critical speeds. The regulation of resonance vibration at critical speeds is established in ISO 10814.

Mechanical vibration -- Vibration of rotating machinery equipped with active magnetic bearings -- Part 3: Evaluation of stability margin

GSO ISO 13374-1:2015 监视和检查设备状况 处理、通信和呈现数据 第1部分：一般指南

This part of ISO 13374 establishes general guidelines for software specifications related to data processing, communication, and presentation of machine condition monitoring and diagnostic information. NOTE Later parts of ISO 13374 (under preparation) will address specific software specification requirements for data processing, communication and presentation.

Condition monitoring and diagnostics of machines -- Data processing, communication and presentation -- Part 1: General guidelines

GSO ISO 18436-5:2015 机器状态监测和诊断 人员资格和评估要求 第5部分：润滑剂实验室技术员/分析员

This part of ISO 18436 specifies the requirements for qualification and assessment of personnel who perform machinery condition monitoring and diagnostics using laboratory-based lubricant analysis. A certificate or declaration of conformity to this part of ISO 18436 provides recognition of the qualifications and competence of individuals to perform laboratory-based lubricant analysis for machinery condition monitoring. It is possible that this procedure is not applicable to specialized equipment or other specific situations. This part of ISO 18436 covers a three-category classification programme that is based on the technical areas delineated herein.

Condition monitoring and diagnostics of machines -- Requirements for qualification and assessment of personnel -- Part 5: Lubricant laboratory technician/analyst

GSO ISO 18436-8:2015 机器状态监测和诊断 人员资格和评估要求 第8部分：超声波

This part of ISO 18436 specifies the requirements for qualification and assessment of personnel who perform machinery condition monitoring and diagnostics using ultrasound. A certificate or declaration of conformity to this part of ISO 18436 provides recognition of the qualifications and competence of individuals to perform ultrasound measurements and analysis for machinery condition monitoring using ultrasound equipment. It is possible that this procedure is not applicable to specialized equipment or other specific situations. This part of ISO 18436 specifies a three-category classification programme that is based on the technical areas delineated herein, consistent with ISO 18436-1 and ISO 18436-3.

Condition monitoring and diagnostics of machines -- Requirements for qualification and assessment of personnel -- Part 8: Ultrasound

ISO 13373-3:2015 机器的工况监测和诊断. 振动状态监测. 第3部分: 振动诊断指南

This part of ISO 13373 sets out guidelines for the general procedures to be considered when carrying out vibration diagnostics of rotating machines. It is intended to be used by vibration practitioners, engineers and technicians and provides a practical structured approach to fault diagnosis. In addition it gives examples of faults common to a wide range of machines. NOTE Guidance for specific machines is provided in other parts of ISO 13373.

Condition monitoring and diagnostics of machines - Vibration condition monitoring - Part 3: Guidelines for vibration diagnosis

DIN ISO 10816-6:2015 机械振动.在非旋转部件上的测量和评定机器振动.第6部分:额定功率在100kW以上的往复式机器(ISO 10816-6-1995+Amd.1-2015)

Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 6: Reciprocating machines with power ratings above 100 kW (ISO 10816-6:1995 + Amd.1:2015)

BS ISO 7626-2:2015 机械振动和冲击. 机械导纳的试验确定. 采用连接激振器的单点平动激励测量

Mechanical vibration and shock. Experimental determination of mechanical mobility. Measurements using single-point translation excitation with an attached vibration exciter

BS ISO 13379-2:2015 机器的状态监测和诊断 数据解释和诊断技术 数据驱动的应用程序

Condition monitoring and diagnostics of machines. Data interpretation and diagnostics techniques. Data-driven applications

BS ISO 10816-21:2015 机械振动. 通过非旋转部件的测量评估机械振动. 带变速箱的水平轴风力涡轮机

Mechanical vibration. Evaluation of machine vibration by measurements on non-rotating parts. Horizontal axis wind turbines with gearbox

BS ISO 18129:2015 机器的工况监测和诊断. 性能诊断方法

Condition monitoring and diagnostics of machines. Approaches for performance diagnosis

ISO 10816-21:2015 机械振动. 通过非旋转零件测量对机械震振动的评估. 第21部分: 带变速箱的水平轴风力涡轮机

This part of ISO 10816 specifies the measurement and evaluation of mechanical vibration of wind turbines and their components by taking measurements on non-rotating parts. It applies to horizontal axis wind turbines with mechanical gearbox and rated generator output exceeding 200 kW and the following design and operational characteristics: a) installation on supporting systems (tower and foundation) made of steel and/or concrete; c) rotor bearing separate from or integrated into the gearbox; e) generators of the synchronous or asynchronous type (mostly equipped with 4-pole generator); b) horizontal axis rotor with several rotor blades; d) generators driven via gearbox; f) generators with only a fixed pole number or which are pole-changeable for speed adjustment; g) output control by rotor blades (pitch or stall wind turbines); h) generator coupled to the power grid via converter or directly. This part of ISO 10816 recommends zones for evaluating the vibration at continuous load operation. However, in most cases, these evaluation zone boundaries might not be suitable for the early detection of faults. This part of ISO 10816 does not specify vibration values for the zone boundaries because there are insufficient data available for the complete range of wind turbines in the worldwide fleet covered by this part of ISO 10816. However, for information only, Annex A presents evaluation zone boundaries for onshore wind turbines. These zone boundaries are based on vibration data from about 1000 wind turbines with rated generator output up to 3 MW. They can be helpful in facilitating discussion between users and manufacturers. Evaluation zone boundaries for offshore wind turbines are not yet available. Although the type and implementation of broad-band vibration monitoring for wind turbines is addressed, this part of ISO 10816 does not apply to diagnostics or fault detection by condition monitoring of wind turbines. NOTE 1 Information on condition monitoring and diagnostics of wind turbines will be given in ISO 16079 (all parts)1). The evaluation of the balance quality of the slowly turning wind turbine rotor, which requires special measurements and analysis, is not covered by this part of ISO 10816. This part of ISO 10816 does not apply to the evaluation of torsional vibration in the drive train. Although coupled lateral and torsional vibration of tower and drive train can affect the amplitudes of the defined vibration characteristics, diagnosis of this kind of vibration source is not feasible by the described measurement methods described in this part of ISO 10816. For general design verification purposes and 1) To be published.  1  for specific fault diagnosis, special measurements are required which are beyond the scope of this part NOTE 2 IEC/TS 61400–13 describes load measurement by use of strain gauges on the supporting structure and blades. Techniques to assist the detection of rolling element bearing and gearbox defects can be found in ISO 13373-2. Measurement and evaluation of structure-borne noise with rolling element bearings are given in VDI 3832. This part of ISO 10816 does not also apply to acceptance measurements on gearboxes and generators in the manufacturer’s test facility. NOTE 3 These are assessed on the basis of appropriate standards namely ISO 8579-2 and IEC 60034–14.

Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 21: Horizontal axis wind turbines with gearbox

GSO ISO 6070:2015 振动发生器辅助表 描述设备特性的方法

This International Standard defines the content of the information flow to be established between manufacturers and users of auxiliary tables with a view to working out related specifications and possibly to comparing in an objective way, the characteristics advertised by the various manufacturers of auxiliary tables and associated guidance systems.

Auxiliary tables for vibration generators -- Methods of describing equipment characteristics

ISO 13379-2:2015 机器的工况监测和诊断. 数据解释和诊断技术. 第2部分: 数据驱动的应用

Condition monitoring and diagnostics of machines - Data interpretation and diagnostics techniques - Part 2: Data-driven applications

ISO 18129:2015 机器的工况监测和诊断. 性能诊断方法

This International Standard provides an introduction on how to apply performance monitoring and diagnostics for machines, groups of machines, up to complete industrial installation (equipment) typically covering the whole lifetime of the machines. This International Standard is intended to — introduce the terminology specifically related to performance monitoring and diagnostics of machines, — describe the types of performance monitoring and diagnostics procedures and their merits, — provide guidance on installation of performance monitoring and diagnostics systems, — outline methods and requirements for carrying out performance monitoring and diagnostics of machines, and — provide information on data interpretation, and assessment criteria and reporting requirements. This International Standard includes testing procedures for determining the accuracy of performance monitoring and diagnostics systems and procedures (including providing inputs for benchmarking the performance of equipment).

Condition monitoring and diagnostics of machines - Approaches for performance diagnosis

ISO 7626-2:2015 机械振动与冲击.机械导纳的试验确定.第2部分:用激振器作单点平动激励测量

This part of ISO 7626 specifies procedures for measuring linear mechanical mobility and other frequencyresponse functions of structures, such as buildings, machines and vehicles, using a single-point translational vibration exciter attached to the structure under test for the duration of the measurement. It is applicable to measurements of mobility, accelerance, or dynamic compliance, either as a drivingpoint measurement or as a transfer measurement. It also applies to the determination of the arithmetic reciprocals of those ratios, such as free effective mass. Although excitation is applied at a single point, there is no limit on the number of points at which simultaneous measurements of the motion response may be made. Multiple-response measurements are required, for example, for modal analyses.

Mechanical vibration and shock - Experimental determination of mechanical mobility - Part 2: Measurements using single-point translation excitation with an attached vibration exciter

DIN ISO 16063-22:2015 振动和冲击传感器的校准方法 第22部分：通过与参考传感器比较进行冲击校准（ISO 16063-22:2005 + Amd.1:2014）

Methods for the calibration of vibration and shock transducers - Part 22: Shock calibration by comparison to a reference transducer (ISO 16063-22:2005 + Amd.1:2014)