17.180.20 颜色和光的测量 标准查询与下载

ASTM E3040-18 用灰度评定仪器色差的标准实施规程

Standard Practice for Evaluation of Instrumental Color Difference with a Gray Scale

ASTM D8005-18 透明液体颜色的标准测试方法（铂钴标准）

1.1 This test method covers a procedure for the visual measurement of the color of near clear liquids. It is applicable only to materials in which the color-producing bodies present have light absorption characteristics nearly identical with those of the Platinum-Cobalt (Pt-Co) color standards used. 1.2 This test method has been found applicable to the color measurement of clear, liquid samples, free of haze, with nominal Pt-Co color values between 0 and 100. It is applicable to nonfluorescent liquids with light absorption characteristics similar to those of the Pt-Co color standard solutions. Test Methods D1209, D1686, and D5386 deal with the visual and instrumental measurement of near-clear liquids. 1.3 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded in accordance with the rounding off methods of Practice E29. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)

KS M 0024-2017 红外分光光度分析通则

General rules for infrared spectrophotometric analysis

KS M 0024-2017(2022) 红外分光光度法分析通则

General rules for infrared spectrophotometric analysis

ASTM E1247-12(2017) 分光光度法检测物体颜色样本荧光的标准实践

1.1 This practice provides spectrophotometric methods for detecting the presence of fluorescence in object-color specimens. NOTE 1—Since the addition of fluorescing agents (colorants, whitening agents, etc.) is often intentional by the manufacturer of a material, information on the presence or absence of fluorescent properties in a specimen may often be obtained from the maker of the material. 1.2 This practice requires the use of a spectrophotometer that both irradiates the specimen over the wavelength range from 340 to 700 nm and allows the spectral distribution of illumination on the specimen to be altered as desired. 1.3 Within the above limitations, this practice is general in scope rather than specific as to instrument or material. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Detecting Fluorescence in Object-Color Specimens by Spectrophotometry

EN 13032-2:2017 灯和照明.灯和灯具光度数据的测量和表示.第2部分:室内和室外工作场所的数据描述

Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 2: Presentation of data for indoor and outdoor work places

ASTM D1500-12(2017) 石油产品ASTM颜色标准测试方法（ASTM色标）

1.1 This test method covers the visual determination of the color of a wide variety of petroleum products, such as lubricating oils, heating oils, diesel fuel oils, and petroleum waxes. NOTE 1—Test Method D156 is applicable to refined products that have an ASTM color lighter than 0.5. 1.2 This test method reports results specific to the test method and recorded as “ASTM Color.” 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale)

ASTM C1864-17e1 用便携式太阳反射计测定定向反射材料的太阳反射率的标准试验方法

Standard Test Method for Determination of Solar Reflectance of Directionally Reflective Material Using Portable Solar Reflectometer

ASTM C1864-17 用便携式太阳反射计测定定向反射材料的太阳反射率的标准试验方法

Standard Test Method for Determination of Solar Reflectance of Directionally Reflective Material Using Portable Solar Reflectometer

PD CEN/TR 16791:2017 量化人类眼睛介导的非成像光效应的辐照度

Quantifying irradiance for eye-mediated non-imageforming effects of light in humans

ASTM E1455-17 使用三刺激色度计从视觉显示单元获取比色数据的标准实践

Standard Practice for Obtaining Colorimetric Data from a Visual Display Unit Using Tristimulus Colorimeters

ASTM E2539-14(2017) 干涉色素多色测量的标准测试方法

1.1 This test method covers the instrumental requirements and required parameters needed to make instrumental color measurements of thin film interference pigments. This test method is designed to encompass interference pigments used in architectural applications, automobiles, coatings, cosmetics, inks, packaging, paints, plastics, printing, security, and other applications. 1.2 Characterization of the optical behavior of materials colored with interference pigments requires measurement at multiple angles of illumination and detection. 1.3 Data taken utilizing this test method are quantitative and are appropriate for quality control of interference pigment color. 1.4 The measurement results are usually expressed as reflectance factors, tristimulus color values, or as CIE L*a*b* color coordinates and color difference. 1.5 The totality of data taken may not be necessary for evaluating mixtures also containing non-interference pigments. The committee is investigating and evaluating the appropriateness of this test method for those materials. It is the responsibility of the users to determine the applicability of this test method for their specific applications. 1.6 Interference pigments are typically evaluated for color and color appearance in a medium, such as paint or ink. The gonioapparent effect depends strongly on the physical and chemical properties of the medium. Some of the properties affecting color and color appearance include vehicle viscosity, thickness, transparency, and volume solids. As a general rule, for quality control purposes, interference pigments are best evaluated in a masstone product form. In some cases this product form may be the final product form, or more typically a qualified simulation of the intended product form (such as a paint drawdown) that in terms of color and appearance correlates to final product application. 1.7 This standard does not address the requirements for characterizing materials containing metal flake pigments. Measurements of the optical characteristics of materials containing metal flake pigments are described in Test Method E2194. 1.8 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 This test method is under the jurisdiction of ASTM Committee E12 on Color and Appearance and is the direct responsibility of Subcommittee E12.12 on Gonioapparent Color. Current edition approved June 1, 2017. Published June 2017. Originally approved in 2008. Last previous edition approved in 2014 as E2539 – 14. DOI: 10.1520/E2539-14R17. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1 2. Referenced Documents

Standard Test Method for Multiangle Color Measurement of Interference Pigments

ASTM E1477-98a(2017) 使用积分球面反射计的声学材料的发光反射系数的标准测试方法

1.1 This test method covers the measurement of the luminous reflectance factor of acoustical materials for use in predicting the levels of room illumination. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers

ASTM E1477-98A(2017)e1 使用积分球面反射计的声学材料的发光反射系数的标准测试方法

Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers

ASTM E1164-12(2017)e1 用于获取对象颜色评估的光谱数据的标准实践

1.1 This practice covers the instrumental measurement requirements, calibration procedures, and material standards needed to obtain precise spectral data for computing the colors of objects. 1.2 This practice lists the parameters that must be specified when spectrometric measurements are required in specific methods, practices, or specifications. 1.3 Most sections of this practice apply to both spectrometers, which can produce spectral data as output, and spectrocolorimeters, which are similar in principle but can produce only colorimetric data as output. Exceptions to this applicability are noted. 1.4 This practice is limited in scope to spectrometers and spectrometric colorimeters that employ only a single monochromator. This practice is general as to the materials to be characterized for color. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation

ASTM E805-12a(2017) 识别材料颜色或色差测量方法的标准实践

1.1 This practice covers the documentation of instrumental measurement of color or color difference for current communication or for future reference. The practice is applicable to instrumental measurements of materials where color is seen by reflected, transmitted or emitted light and any combinations of one or more of these processes. The practice is recommended for documentation of methodology in interlaboratory colormeasurement programs. 1.2 Providing an adequate identification of an instrumental measure of color or color-difference involves documenting the metadata necessary for archiving and future use of the measurement data collected. The metadata can be divided in five parts: 1.2.1 Nature and source of available samples and the form of specimens actually measured, 1.2.2 Instrumental conditions of measurement, including instrument geometrical and spectral conditions of measurement, 1.2.3 Standards used, 1.2.4 Data acquisition procedure, and 1.2.5 Color scales employed. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials

ASTM E2214-17 指定和验证色彩测量仪器性能的标准实践

1.1 This practice provides standard terms and procedures for describing and characterizing the performance of spectral and filter based instruments designed to measure and compute the colorimetric properties of materials and objects. It does not set the specifications but rather gives the format and process by which specifications can be determined, communicated and verified. 1.2 This practice does not describe methods that are generally applicable to visible-range spectroscopic instruments used for analytical chemistry (UV-VIS spectrophotometers). ASTM Committee E13 on Molecular Spectroscopy and Chromatography includes such procedures in standards under their jurisdiction. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Specifying and Verifying the Performance of Color-Measuring Instruments

ASTM E308-17 使用CIE系统计算物体颜色的标准实践

Standard Practice for Computing the Colors of Objects by Using the CIE System

ASTM E1336-11(2017) 通过光谱辐射法从视觉显示单元获取比色数据的标准测试方法

1.1 This test method prescribes the instrumental measurements required for characterizing the color and brightness of VDUs. 1.2 This test method is specific in scope rather than general as to type of instrument and object. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Obtaining Colorimetric Data From a Visual Display Unit by Spectroradiometry

JIS Z 8781-6:2017 比色法.第6部分:CIEDE2000色差公式

Colorimetry -- Part 6: CIEDE2000 Colour-difference formula