17.180.20 颜色和光的测量 标准查询与下载

BS ISO/CIE 19476:2014 照度计和亮度计的性能特征

Characterization of the performance of illuminance meters and luminance meters

ISO/CIE 19476:2014 照度计和亮度计的性能特征

Characterization of the performance of illuminance meters and luminance meters

EN 61966-12-2:2014 多媒体系统和设备-颜色测量和管理-第 12-2 部分：用于识别色域的简单元数据格式

IEC 61966-12-1:2014(en) specifies the colour gamut metadata format for video systems intended for use in CE (Consumer Electronics) devices. The metadata specified in this part of IEC 61966 is limited to the gamut description of additive three primary colours type displays whose white and black points have the same chromaticity. It is fundamentally based on the conventional VESA-EDID format.

Multimedia systems and equipment - Colour measurement and management - Part 12-2: Simple metadata format for identification of colour gamut

HG/T 4608-2014 光学功能薄膜 颜色的测量方法

本标准规定了采用国际照明委员会(Commission Internationale de L' Eclairage,以下简称CIE)1931标准色度系统或CIE 1964标准色度系统测量光学功能薄膜颜色的方法。CIE 1931标准色度系统的三刺激值和色品坐标适用于1°~4°视场时光学功能薄膜的视觉等同颜色;CIE 1964标准色度系统的三刺激值和色品坐标适用于大于4°视场时光学功能薄膜的视觉等同颜色。本标准适用于光学功能薄膜透射色及反射色的测量,也适用于其他透明或半透明物体颜色的测量。

Optical functional films.Color measurement

ASTM C1650-14 用于平板玻璃 涂层和无涂层的颜色的仪器反射测量的标准实践

4.1 Color measurement quantifies the coating color for glass and is often related to coating thickness and composition as well as tinting used in the substrate glass. The user of this document defines an acceptable range of color appropriate for the end use. Typical quality concerns for the reflected color measurement of coated glass products are an indication of consistency in the coating process and verification of lot-to-lot color consistency for end-user acceptance. 4.2 If the reflected color of a glass product is consistent from lot-to-lot and within agreed supplier-buyer acceptance criteria, that product color is expected to be consistent and acceptable for end-use. 1.1 This practice provides guidelines for the instrumental reflectance measurement of the color of flat, coated and uncoated glass. See Terminology E284. 1.2 The practice specifically excludes fluorescent and iridescent samples. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Instrumental Reflectance Measurement of Color for Flat Glass, Coated, and Uncoated

BS ISO/CIE 11664-6:2014 比色测定法. CIEDE2000色差公式

Colorimetry. CIEDE2000 Colour-difference formula

ISO/CIE 11664-6:2014 比色法.第6部分:CIEDE2000色差公式

Colorimetry - Part 6: CIEDE2000 Colour-difference formula

ASTM E2194-14(2017) 金属薄片染色材料多角度颜色测量的标准试验方法

5.1 Instrumental Measurement Angles—This test method is designed to provide color data at specific measurement angles that can be utilized for quality control, color matching, and formulating in the characterization of metal flake pigmented materials. 5.2 Materials—This test method provides meaningful color information for metal flake pigmented materials. This test method has been tested and verified on paint and coatings, and the same principles should apply to plastics containing metallic flake. For materials containing pearlescent materials refer to Test Method E2539. 5.3 Utilization—This test method is appropriate for measurement and characterization of metal flake pigmented materials. These data may be used for quality control, incoming inspection, or color correction purposes. 5.4 Specimen Requirements—Even though a pair of specimens have the same color values at three angles, if there are differences in gloss, orange peel, texture, or flake orientation, they may not be a visual match. Note 2: Information presented in this test method is based upon data taken on metallic materials coatings. Applicability of this test method to other materials should be confirmed by the user. 1.1 This test method covers the instrumental requirements, standardization procedures, material standards, and parameters needed to make precise instrumental measurements of the colors of gonioapparent materials. This test method is designed to encompass gonioapparent materials; such as, automotive coatings, paints, plastics, and inks. 1.2 This test method addresses measurement of materials containing metal flake and pigments. The measurement of materials containing metal flakes requires three angles of measurement to characterize the colors of the specimen. The optical characteristics of materials containing pearlescent and interference materials are not covered by this test method. Note 1: Data taken by utilizing this test method are for gonio-appearance quality control purposes. This procedure may not necessarily supply appropriate data for spatial-appearance or pigment identification. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5 This interna......

Standard Test Method for Multiangle Color Measurement of Metal Flake Pigmented Materials

ASTM E2194-14 金属包片有颜色材料的多角度颜色测量的标准试验方法

5.1 Instrumental Measurement Angles—This test method is designed to provide color data at specific measurement angles that can be utilized for quality control, color matching, and formulating in the characterization of metal flake pigmented materials. 5.2 Materials—This test method provides meaningful color information for metal flake pigmented materials. This test method has been tested and verified on paint and coatings, and the same principles should apply to plastics containing metallic flake. For materials containing pearlescent materials refer to Test Method E2539. 5.3 Utilization—This test method is appropriate for measurement and characterization of metal flake pigmented materials. These data may be used for quality control, incoming inspection, or color correction purposes. 5.4 Specimen Requirements—Even though a pair of specimens have the same color values at three angles, if there are differences in gloss, orange peel, texture, or flake orientation, they may not be a visual match. Note 2: Information presented in this test method is based upon data taken on metallic materials coatings. Applicability of this test method to other materials should be confirmed by the user. 1.1 This test method covers the instrumental requirements, standardization procedures, material standards, and parameters needed to make precise instrumental measurements of the colors of gonioapparent materials. This test method is designed to encompass gonioapparent materials; such as, automotive coatings, paints, plastics, and inks. 1.2 This test method addresses measurement of materials containing metal flake and pigments. The measurement of materials containing metal flakes requires three angles of measurement to characterize the colors of the specimen. The optical characteristics of materials containing pearlescent and interference materials are not covered by this test method. Note 1: Data taken by utilizing this test method are for gonio-appearance quality control purposes. This procedure may not necessarily supply appropriate data for spatial-appearance or pigment identification. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Multiangle Color Measurement of Metal Flake Pigmented Materials

ASTM E1213-14 热成像系统用可分辨的最小温度差的标准实施规程

5.1 This practice relates to a thermal imaging system's effectiveness for discerning details in a scene. 5.2 MRTD values provide estimates of resolution capability and may be used to compare one system with another. (Lower MRTD values indicate better resolution.) 5.3 Due to the partially subjective nature of the procedure, repeatability and reproducibility are apt to be poor and MRTD differences less than 0.2°C are considered to be insignificant. Note 1: Values obtained under idealized laboratory conditions may or may not correlate directly with service performance. 1.1 This practice covers the determination of the minimum resolvable temperature difference (MRTD) capability of the compound observer-thermal imaging system as a function of spatial frequency. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Minimum Resolvable Temperature Difference for Thermal Imaging Systems

KS A 0068-2013 光源色测定法

이 표준은 2도 시야 XYZ 색 표시계1)(이하 XYZ 색 표시계라고 한다.) 및 10도 시야 X10Y10Z10 색 표시계2)(이하 X10Y10Z10 색 표시계라고 한다.)에 따라 태양광과 같은 자연조명, 인공조명 및 발광형 디스플레이 기기 등과 같은 광원으로부터 방출되는 빛의 색을 측정하는 데 적용한다. 덧붙여, 이 표준은 광원으로부터 방출되는 빛의 가시광선 영역(380 nm∼780 nm) 상대분광분포를 측정하는 방법을기술하고 있으며, 이를 물체색의 삼자극치 계산 시 이용하는 조명광의 상대분광분포 측정에 적용할수 있다.

Methods of colour measurement for light sources

KS A 0012-2013 光源色的颜色名称

이 표준은 광원의 색을 표시하는 데 이용하는 색 이름(이하 색 이름이라 한다.)에 대하여 규정한다.

Names of light-source colours

KS A 0062-2013(2023) 颜色规格？根据其三个属性进行规范

Colour specification?Specification according to their three attributes

KS A 0062-2013 根据色彩三要素的颜色表示法

이 표준은 표면색(이하 색이라 한다.)의 색감각의 3속성(색상, 명도, 채도)을 따라서 표시하는 방법에대하여 규정한다. 다만, 형광을 발하는 물체의 색은 적용하지 않는다.

Colour specification ? Specification according to their three attributes

GSO IEC 61966-2-5:2013 多媒体系统和设备 色彩管理和测量 第2-5部分：色彩管理 RGB 色彩空间选择 (RGB) RGB 选择

is applicable to the encoding and communication of RGB colours optionally used in computer systems and similar applications by defining encoding transformations for use in defined reference conditions.

Multimedia systems and equipment - Colour measurement and management - Part 2-5: Colour management - Optional RGB colour space - opRGB

KS A 0062-2013(2018) 颜色规格 根据它们的三个属性

Colour specification?Specification according to their three attributes

KS M 0026-2013 荧光光度分析法通则

이 표준은 형광 광도 분석 장치를 이용하여 185 nm∼1 200 nm에 있어서의 형광의 강도를 측정하고,이에 의하여 무기물 및 유기물의 분석을 행하는 일반사항에 대하여 규정한다.

General rules for fluorometric analysis

JIS Z 8781-4:2013 比色法.第4部分:CIE 1976 L*a*b*颜色空间

Colorimetry.Part 4: CIE 1976 L*a*b* Colour space

JIS Z 8781-5:2013 比色法.第5部分:CIE 1976 L*u*v*颜色空间和u'、v'均匀色度比例图

Colorimetry.Part 5: CIE 1976 L*u*v* Colour space and u', v' uniform chromaticity scale diagram

GSO IEC 61966-12-1:2013 媒体系统和设备 色彩管理和测量 第12-1部分：用于确定色域的元数据

This part of IEC 61966 defines the colour gamut metadata scheme for video systems and similar applications. The metadata can be associated with wide gamut video colour content or to a piece of equipment to display the content. When associated with content, the colour gamut metadata defines the gamut for which the content was created. It can be used by the display for controlled colour reproduction even if the display’s colour gamut is different from that of the content. When associated with a display, the colour gamut metadata defines the display colour gamut. It can be used during content creation to enable improved colour reproduction. The colour gamut metadata may cover associated colour encoding information, which includes all information required for a controlled colour reproduction, when such information is not provided by the colour encoding specification. The colour gamut metadata scheme provides scalable solutions. For example, more flexible solutions will be used for the professional use, while much simpler solutions will be used for consumer use with easier product implementation. This part of IEC 61966 only defines the colour gamut metadata scheme. Vendor-specific solutions for creation and end-use of this metadata are allowed.

Multimedia systems and equipment - Colour measurement and management - Part 12-1: Metadata for identification of colour gamut (Gamut ID)