17.200 热力学和温度测量 标准查询与下载

GSO OIML D19:2013 模型评估和模型批准

This International Document is addressed primarily to two groups — OIML Secretariats and legal metrology officials — concerned with pattern evaluation and pattern approval of measuring instruments. OIML Secretariats are responsible for the drafting of International Recommendations for measuring instruments subject to pattern evaluation and approval. Legal metrology officials are responsible for the adoption and implementation of pattern evaluation and pattern approval requirements.

Pattern evaluation and pattern approval

SB/T 10928-2012 易腐食品冷藏链温度检测方法

本标准规定了易腐食品冷藏链各环节中环境空气温度和食品温度的检测要求和方法。本标准适用于易腐食品在冷藏链加工、贮藏、运输、销售各环节及环节间的环境空气温度、食品或其包装的表面温度和食品中心温度的测量。通过冷藏链流通的其他货物,其有关温度测量方法可参照本标准执行。

Temperature measurement in perishable food cold chain

DB15/T 501-2011 住宅采暖室内空气温度测量方法

Method for measuring air temperature in residential heating room

DB11/T 745-2010 住宅采暖室内空气温度测量方法

本标准规定了住宅采暖室内空气温度测量的测量仪器技术要求、测量条件、测量方法、数据处理及测量记录与报告的相关要求。本标准适用于以温度测量器具在集中供暖住宅室内进行的空气温度测量（包括第三方检测机构进行的室内空气温度测量和日常室内空气温度监测）。

Method for measuring air temperature in residential heating room

CSA C900.1-2006(R2011) 热量表 第1部分：一般要求

This is the first edition of CSA C900.1, Heat meters - Part 1: General requirements, which is an adoption, with Canadian deviations, of the identically titled CEN (European Committee for Standardization) Standard EN 1434-1 (first edition, 1997-02), including amendment A1:2002. 1 Scope This European Standard applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed or given up by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units. Electrical saflety requirements are not covered by this standard. Meters with surface mounted temperature sensors are not yet included in this standard. Part 1 specifies general requirements.

Heat Meters - Part 1: General Requirements

CSA C900.4-2006(R2011) 热量表 第4部分：型式认可测试

CSA Preface This is the first edition of CSA C900.4, Heat meters - Part 4: Pattern approval tests, which is an adoption, with Canadian deviations, of the identically titled CEN (European Committee for Standardization) Standard EN 1434-4 (first edition, 1997-02), including amendment A1:2002. 1 Scope This European Standard applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed or given up by a liquid called the heat-conveying liquid. The meter indicates heat quantity in legal units. Electrical safety requirements are not covered by this standard. Meters with surface mounted temperature sensors are not yet included in this standard. Part 4 specifies pattern approval tests.

Heat Meters - Part 4: Pattern Approval Tests

CSA C900.3-2006(R2011) 热量表 第3部分：数据交换和接口

CSA Preface This is the first edition of CSA C900.3, Heat meters - Part 3: Data exchange and interfaces, which is an adoption without modification of the identically titled CEN (European Committee for Standardization) Standard EN 1434-3 (first edition, 1997-02). 1 Scope This European standard applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed or given up by a liquid called the energy-conveying liquid. The meter indicates heat in legal units. Electrical safety requirements are not covered by this standard. Part 3 specifies the data exchange between a meter and a read-out device (POINT / POINT communication). For these applications using the optical readout head and the CL interface, the EN 61 107 protocol is recommended. Further stipulations are set out for the data communication between several meters and one master unit in a local network (MULTI-POINT communication). This can be done with a few meters with a hand held master unit by using the inductive interface on the Meter-Bus (in the following called the M-Bus). For bigger networks with up to 250 meters, a master unit with AC mains supply is necessary to control the M-Bus. For these applications a protocol according to EN 60870-5 is recommended.

Heat meters - Part 3: Data exchange and interfaces

CSA C900.2-2006(R2011) 热量表 第2部分：结构要求

CSA Preface This is the first edition of CSA C900.2, Heat meters - Part 2: Constructional requirements, which is an adoption, with Canadian deviations, of the identically titled CEN (European Committee for Standardization) Standard EN 1434-2 (first edition, 1997-02), including amendment A1:2002. 1 Scope This European Standard applies to heat meters, that is to instruments intended for measuring the heat which, in a heat-exchange circuit, is absorbed or given up by a liquid called the heat-conveying liquid. The heat meter indicates the quantity of heat in legal units. Electric safety requirements are not covered by this standard Meters with surface mounted temperature sensors are not yet included in this standard.

Heat Meters - Part 2: Constructional Requirements

DB22/T 428-2005 采暖室内空气温度检测方法

Heating indoor air temperature detection method

NY/T 858-2004 沼气压力表

Biogas pressure meter

GSO 1553:2002 由铂、铜或镍制成的电阻热传感器（用于商业和工业用途）

This standard specifies the metrological characteristics required for electrical resistance thermometer sensors (hereinafter referred to as “sensors”) having a sensing element made of platinum, copper or nickel, designed for use in measuring temperatures in the range - 200oC to + 850oC, or in a part of that range, and intended for industrial and commercial use. It does not apply to instruments for the measurement of resistance, nor to indicating instruments

Resistance thermometer sensors made of platinum,copper or nickel ( for industrial and commercial use)

GSO ISO 1770:1997 通用实心柄螺纹

This standard specifies the requirements for two series of inexpensive “commercial quality” liquid-in-glass thermometers of the solid-stem type suitable for general purpose use in industry, schools and laboratories when great accuracy of measurement is not required: a) a series designated A to H, in which nominal ranges and maximum overall length are specified but which may not be acceptable for testing by the authorized national verification laboratory; b) A series designated J to W of greater accuracy than in a) and with specified ranges and a tolerance on overall length, which may be acceptable for testing by the authorized national verification laboratory. The temperature range covered by each series is from – 100oC to +500oC.

Solid-stem general purpose thermometers.

SNI 19-1141-1989 温度. 测试方法

Temperature, Test method

YB 4084-92 快速测量钢液温度用钨铼热电偶

Tungsten-rhenium thermocouple for rapid measurement of molten steel temperature