温度测量仪器仪表标准-分析测试百科网

JIS B 7411-2:2014 一般用途玻璃温度计.第2部分:处理或认证中使用的测量仪器

Glass thermometers for general -- Part 2: Measuring instruments used in transaction or certification

ICS: 17.200.20
CCS: N11
发布: 2014-03-01
实施

ASTM E2623-14 温度计校准报告的标准实践规程

5.1 This practice is adequate for use with all ASTM Test Methods which require the reporting of temperature measurements. 5.2 The Report of Calibration, however named, is the physical output of the calibration laboratory. It shall be prepared so that both the results of the measurement(s) and the non-technical information necessary to support those results are conveyed in a manner that ensures accurate communication and justification of the results. 5.3 This practice is not meant to supersede requirements of other standards practice such as ISO/IEC 17025 or ANSI/NCSL Z540.3. 1.1 This practice contains reporting requirements for thermometer calibrations included in ASTM Committee E20 Test Methods. 1.2 This practice covers reports of calibration for radiation thermometers, liquid-in-glass thermometers, resistance thermometers, digital thermometers, and new thermocouples. Note 1: This practice does not apply to used thermocouples. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Reporting Thermometer Calibrations

ICS: 17.200.20
CCS
发布: 2014
实施

ASTM E1543-14 热成像系统的噪声等效温差的标准实施规程

5.1 This practice gives an objective measure of the temperature sensitivity of a thermal imaging system (relative to a standard reference filter) exclusive of a monitor, with emphasis on the detector(s) and preamplifier. Note 1: Test values obtained under idealized laboratory conditions may or may not correlate directly with service performance. 5.2 This practice affords a convenient means for periodically monitoring the performance of a given thermal imaging system. 5.3 NETD relates to minimum resolvable temperature difference as described in Practice E1213. Thus, an increase in NETD may be manifest as a loss of detail in imagery. 5.4 Intercomparisons based solely on NETD figures may be misleading. Note 2: NETD depends on various factors such as spectral bandwidth and background temperature. 1.1 This practice covers the determination of the noise equivalent temperature difference (NETD; NEΔT) of thermal imaging systems of the conventional forward-looking infrared (FLIR) or other types that utilize an optical-mechanical scanner; it does not include charge-coupled devices or pyroelectric vidicons. 1.2 Parts of this practice have been formulated under the assumption of a photonic detector(s) at a standard background temperature of 295°K (22°C). Besides nonuniformity, examinations made at other background temperatures may result in impairment of precision and bias. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Noise Equivalent Temperature Difference of Thermal Imaging Systems

ICS: 17.200.20
CCS
发布: 2014
实施

ASTM E1129/E1129M-14 热电偶连接器的标准规格

4.1 The widespread use of thermocouple connectors requires standardization of mating dimensions and performance characteristics. 4.2 This specification describes standardized thermocouple connector dimensions and capabilities and includes test procedures suitable for evaluating the performance of a particular specimen or design. The tests described are not intended for routine inspection or rapid testing of large groups of connectors or for quality control purposes. 1.1 This specification covers separable single-circuit thermocouple connectors with two round pins. Connectors covered by this specification must be rated for continuous use to at least 300 °F (150 °C), but they may optionally be rated higher. 1.2 This specification does not cover multiple-circuit connectors, multi-pin connectors, miniature connectors, or connectors intended primarily for panel mounting. High temperature connectors (for example, those designed for continuous use at temperatures above approximately 500 °F (260 °C)) are not intended to be covered by this specification. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. 1.4 The following precautionary statement pertains only to the test method portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Thermocouple Connectors

ICS: 17.200.20
CCS
发布: 2014
实施

BS EN 60584-1:2013 热电偶. 电动势 (EMF) 规格和公差

Thermocouples. EMF specifications and tolerances

ICS: 17.200.20
CCS: N11
发布: 2013-12-31
实施: 2013-12-31

KS L ISO 1146-2013(2018) 测温锥实验室用规格

Pyrometric reference cones for laboratory use?Specification

ICS: 17.200.20
CCS
发布: 2013-12-19
实施

KS L ISO 1146-2013(2023) 实验室用高温参考锥？规格

Pyrometric reference cones for laboratory use?Specification

ICS: 17.200.20
CCS
发布: 2013-12-19
实施

KS L ISO 1146:2013 耐火度试验用标准锥

1.1 이 표준은 주로 요업 원료 및 요업 제품에 대하여 1 500 ℃∼1 800 ℃의 온도에서 내화 재료의내화도를 측정하는 표준 콘의 특성에 대하여 규정한다.1.2 이 표준에서 1 500 ℃∼1 800 ℃ 사이의 측정이 아닌 것은 ISO 528에 규정된 절차로 측정하는것이 적절하다.

Pyrometric reference cones for laboratory use ? Specification