1780 标准查询与下载

DIN 89283:1994 电缆引入管.螺纹套筒

In this document grommets for cable glands are specified. They are suitable for the connection of flexible cables with movable utilization devices and installation material, with type of enclosure IP 56 according to DIN 40050.#,,#

Glands for cables; screw bushes

DIN 47626:1990 通信电缆的加护套卡子.要求和试验

Sheath-clamps for telecommunication cables; requirements, tests

DIN 46264:1988 浇注树脂绝缘子的高压引线端子

Feed-through terminals with ceramic insulator as standardized up until now in DIN 46265 part 1 and, in particular, those used for electrical machines are no longer sufficient for high system short-circuit powers. Therefore feed-through terminals with cast resin insulators and four flange mounting holes has been standardized.

High-voltage feed-through terminals with cast resin insulator

DIN 22412:1986 有槽螺栓

Slit-bolts are used for connecting electrical cables which have to be especially protected against working loose. The standard deals with three designs (types of construction). Dimensions, materials, minimum torques and correlation of conductors are specified.

Slit-bolts

DIN 46294:1985 带有６个接线柱的矩形端子板.主要尺寸

Terminal board, square shaped with six terminals; main dimensions

DIN 42017:1984 小型电动机线路接头的配置和标记

Marking and coordination of the connecting leads for small motors

IEC 60685-2-4:1983 家用或类似固定电气装置用接线器件[端接和(或)分接].第2部分:特殊要求.第4节:铜导线用扭接式接线器件

Connecting devices (junction and/or tapping) for household and similar fixed electrical installations. Part 2 : Particular requirements - Twist-on connecting devices for copper conductors

DIN 42801:1980 电位均衡导线用接线装置

Connection device for potential equalization conductorsFür den Geltungsbereich dieser Norm bestehen keine entsprechenden regionalen oder internationalen Normen.

Connection device for potential equalization conductors

DIN 46200:1977 １·６ＫＡ以下导电连接螺栓.电流强度的设计和给定

Current carrying connection bolts up to 1600 A; design and assignment of current intensitiesDiese Norm gilt für stromführende Anschlu?bolzen bis 1600 A zum Anschlu? von Leitern mit Lei-tungs?sen, von eindr?htigen Leitern mit angebogenen ?sen z. B. nach B

Current carrying connection bolts up to 1600 A; design and assignment of current intensities

DIN 47658:1975 铜和铝导线的屋内连接线的分线端子

Branch terminals in house connections for copper and aluminium conductors

Branch terminals in house connections for copper and aluminium conductors

DIN 47659:1975 150mm以下的波纹同心铜导线接地连接器

Earthing connector for corrugated concentric copper-conductor up to 150 mm

Earthing connector for corrugated concentric copper-conductor up to 150 mm<(hoch)2>

DIN 46288:1974 导线连接垫圈

Connecting washers for conductorsAnschlu?scheiben nach dieser Norm sind vorzugsweise für die Verwendung bei raumsparenden Konstruktionen vor-gesehen und für den Anschlu? von 1 oder 2 Leitern mit gleichen oder verschiedenen Querschnitten geeignet. Sie hab

Connecting Washers for Conductors

DIN 46285:1972 交流380V直流440V.2.5MM2平方以下导线的一极至三极插座式端子板（灯具端子）

One to three-pole socket terminal strips (lighting fixture terminals) 380 V A. C. and 440 V D. C. for conductors up to 2,5 mmEs wird auf die entsprechenden Bestimmungen, z. B. VDE 0606, VDE 0609, hingewiesen. Die Kriech- und Luftstrecken entsprechen

One to three-pole socket terminal strips (lighting fixture terminals) 380 V a.c. and 440 V d.c. for conductors up to 2,5 mm<(hoch)2>

DIN 46284:1972 交流380V直流440V.2.5mm2平方以下导线的二极和三极插座式端子板(仪器端子)

Two- and three-pole socket terminal strips (appliance terminals) 380 V A. C. and 440 V D. C. for conductors up to 2,5 mmEs wird auf die entsprechenden Bestimmungen, z. B. VDE 0606, VDE 0609, hingewiesen. Die Kriech- und Luftstrecken entsprechen VDE

Two- and three-pole socket terminal strips (appliance terminals) 380 V a.c. and 440 V d.c. for conductors up to 2,5 mm<(hoch)2>

DIN 46218:1966 导线用冲压金属环.

Stamped metal rings for conductors

Stamped metal rings for conductors