19.020 试验条件和规程综合 标准查询与下载

DB34/T 4307.1-2022 内河水下工程结构物检测与评定技术规范 第1部分：桥梁部分

Technical specifications for detection and assessment of underwater engineering structures in inland rivers Part 1: bridge part

T/CSEE 0288-2022 燃煤电厂烟囱雨监测方法

本文件规定了燃煤电厂烟囱雨监测的总体原则、监测准备和监测方法。 本文件适用于燃煤电厂湿烟气排放的烟囱雨监测，其他湿烟气排放的烟囱雨监测可参照使用。

Coal-fired power plant chimney rain monitoring method

T/CSEE 0303-2022 高强度高伸长率铝包钢芯铝合金绞线

本文件规定了高强度高伸长率铝包钢芯铝合金绞线的产品分类及表示方法、质量要求、试验方法、检验规则，以及包装、标志、运输和贮存。 本文件适用于高强度高伸长率铝包钢芯铝合金绞线的生产、采购、检验、验收和应用。

High strength and high elongation aluminum clad steel core aluminum alloy stranded wire

T/CSEE 0301-2022 1000 kV 分级式可控并联电抗器施工工艺导则

本文件规定了 1000 kV 分级式可控并联电抗器的施工工艺，包括总体要求、施工流程、质量要求。 本文件适用于 1000 kV 分级式可控并联电抗器的施工。

Construction process guidelines for 1000 kV hierarchical controllable shunt reactors

T/CSEE 0310.1-2022 兆瓦级电热泵控制及信息系统技术规范 第 1 部分：信息系统集成

本文件规定了兆瓦级电热泵控制及信息系统的集成原则、机组要求、信息系统集成、系统运行与维护的要求。 本文件适用于兆瓦级电热泵的信息系统集成。

Technical Specifications for Megawatt Electric Heat Pump Control and Information Systems Part 1: Information System Integration

T/CSEE 0307-2022 高压开关环氧绝缘部件 X 射线数字成像检测技术导则

本文件规定了高压开关环氧绝缘部件 X 射线数字成像检测的技术条件、检测方法和评定。 本文件适用于交流电压 40.5 kV 以上开关设备用环氧浇筑绝缘部件的 X 射线数字成像检测。

Technical Guidelines for X-ray Digital Imaging Inspection of High Voltage Switch Epoxy Insulation Components

T/CSEE 0306-2022 油浸式电力变压器纸质绝缘材料 X 射线 数字成像检测技术导则

本文件规定了油浸式电力变压器纸质绝缘材料 X 射线数字成像检测的技术条件、检测方法、质量分级和评定。 本文件适用于交直流电压 110 kV～1100 kV 变压器纸质绝缘材料 X 射线数字成像检测。 配电网及其他类别变压器纸质绝缘材料可参照本文件。

Technical Guidelines for X-ray Digital Imaging Detection of Paper Insulating Materials of Oil-immersed Power Transformers

T/CSEE 0302-2022 架空输电线路水土保持设施质量检验及评定规程

本文件规定了架空输电线路水土保持设施质量检验及评定的项目划分原则以及工程施工质量检验、评定及检查方法。 本文件适用于 500 kV 及以上架空输电线路水土保持设施质量检验及评定，其他电压等级可参照执行。

Regulations for quality inspection and assessment of soil and water conservation facilities for overhead transmission lines

T/CSEE 0300-2022 220 kV～1000 kV 串补站设计技术规范

本文件规定了 220 kV～1000 kV 串补站及串补装置的设计原则，主要内容涵盖对应各电压等级串补站、变电站串补装置的设计要求。 本文件适用于新建 220 kV～1000 kV 串补站的设计，扩建或改建工程可参照执行。

220 kV～1000 kV series compensation station design technical specifications

T/CSEE 0310.2-2022 兆瓦级电热泵控制及信息系统技术规范 第 2 部分：灵活性运行控制

本文件规定了兆瓦级电热泵灵活性运行控制的基本规定、灵活运行、调度控制、系统通信及安全管理的要求。 本文件适用于兆瓦级电热泵的灵活性运行控制。

Technical specifications for megawatt electric heat pump control and information systems Part 2: Flexible operation control

T/CSEE 0295-2022 火电厂旁路供热改造安全预评价导则

本文件规定了火电厂旁路供热改造工程安全预评价的程序、内容和基本要求等。 本文件适用于火电厂旁路供热改造工程的安全预评价。 本文件适用于利用汽轮机原有旁路系统或新增减温减压系统进行供热的多种型式的旁路供热改造工程，包括但不限于主蒸汽直接减温减压供热、热再热蒸汽直接减温减压供热、冷再热蒸汽直接减温减压供热、新增或利用原低压旁路供热、新增或利用原高低压两级旁路供热等旁路供热改造工程。

Guidelines for safety pre-evaluation of bypass heating renovation in thermal power plants

T/ZSA 119-2022 柔性电子双轴拉伸测试系统

本文件规定了柔性电子双轴拉伸测试系统（以下简称“仪器”）的术语和定义、仪器结构、技术要求、试验方法、检验规则、标志、包装、运输与贮存。  本文件适用于柔性电子双轴拉伸测试系统的设计、检验和使用。

Flexible electronic biaxial tensile analysis systems

T/ZSA 120-2022 原位冷热台

本文件规定了原位冷热台（以下简称“仪器”）的术语和定义、仪器结构、技术要求、试验方法、检验规则、标志、包装、运输及贮存。 本文件适用于原位冷热台的设计、检验和使用。

In situ cold and thermal analysis platform

ASTM D6646-03(2022) 测定颗粒和丸状活性炭加速硫化氢漏过容量的标准试验方法

1.1 This test method is intended to evaluate the performance of virgin, newly impregnated or in-service, granular or pelletized activated carbon for the removal of hydrogen sulfide from an air stream, under the laboratory test conditions described herein. A humidified air stream containing 1 % (by volume) hydrogen sulfide is passed through a carbon bed until 50 ppm breakthrough of H2S is observed. The H2S adsorption capacity of the carbon per unit volume at 99.5 % removal efficiency (g H2S/cm3 carbon) is then calculated. This test is not necessarily applicable to non-carbon adsorptive materials. 1.2 This standard as written is applicable only to granular and pelletized activated carbons with mean particle diameters (MPD) less than 2.5 mm. See paragraph 5.3 if activated carbons with larger MPDs are to be tested. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of the Accelerated Hydrogen Sulfide Breakthrough Capacity of Granular and Pelletized Activated Carbon

T/CASTENG 001-2022 食品安全快速检测实验室管理技术规范

食品安全快速检测实验室管理要求分为管理体系、档案管理，以及实验室管理的技术要求为仪器设备、试剂耗材、人员、环境、采样及制样、检测、结果及记录、异常样品处理、质量控制、其他要求等。

Technical specifications for food safety rapid testing laboratory management

T/REIANM 0304-2022 新能源车用高性能钕铁硼永磁体极端工况条件下磁性能经时变化试验方法

本文件从术语、定义、方法提要、仪器设备、试验方法、试验数据处理、结果报告等方面规定了新能源车用烧结钕铁硼永磁体，在环氧树脂涂层防护条件下，经极端工况后磁性能经时变化的试验测定方法。

Text method for time-varying magnetic properties of high-performance NdFeB magnets for New Energy Vehicles under extreme working conditions

ASTM D5818-22 评估土工合成材料安装损坏的样品暴露和回收的标准实施规程

1.1 This practice covers standardized procedures for obtaining samples of geosynthetics from a test section for use in assessment of the effects of damage immediately after installation caused only by the installation techniques. The assessment may include physical testing. This practice is applicable to any geosynthetic except those installed between layers of aggregate or soil modified by a binder. NOTE 1—The binder would inhibit the retrieval of the geosynthetic without inflicting further damage to the geosynthetic. Other practices may be suitable for retrieving geosynthetics used in these applications but are out of the scope of this practice. 1.2 This practice is limited to full-scale test sections and does not address laboratory modeling of field conditions. This practice does not address which test method(s) to use for quantifying installation damage. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics

ASTM D7252-22 聚氨酯原材料的标准试验方法:异氰酸酯中单体和异构体的测定

1.1 This test method determines the percent by weight of monomeric isomers and total monomer in crude or modified isocyanates. The test method is applicable to methylene di(phenylisocyanate) (MDI) and polymeric (methylene phenylisocyanate) (PMDI). (See Note 1.) 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Polyurethane Raw Materials: Determination of Monomer and Isomers in Isocyanates

T/CTSA 0011-2022 虚拟演出交互实验平台测试规范

基于主动视觉的复杂观演空间三维全景感知与建模，基于多源异构数据融合的多目标演员实时定位、跟踪与动作识别，面向大尺度复杂异形立体投影面的实时自适应内容呈现等关键技术，进而研建虚实演出交互实验平台，测试上述关键技术的可用性与集成度，验证虚实融合的观演互动模式。

Specification for virtual performance interactive experimental platformtest

ASTM E2480-12(2022) 采用多值测量方法进行实验室间研究以确定测试方法精度的标准做法

1.1 This practice describes the techniques for planning, conducting, and analyzing the results of an interlaboratory study (ILS) conducted for certain test methods within Committee E12. 1.2 This practice does not concern itself with the development of the test method but rather with the gathering of the information needed for the precision and bias statement after the completion of development of the test method. The data obtained in the ILS may indicate, however, that further effort is needed to improve the test method. 1.3 This practice is concerned exclusively with test methods that derive a multi-valued measurand, such as, but not limited to, spectral reflectance, transmittance function, tristimulus values, or RGB values. Variation in measurements of such multi-valued measurands are usually analyzed by reducing the data to a single-valued parameter, such as color difference, ∆E. 1.4 This practice covers methods of dealing with the nonnormal distribution of the variation of sets of color-differences. This is done so that the user may derive valid statistics from such non-normal distributions. 1.5 This practice does not cover test methods, even in Committee E12, whose measurands are single-valued, or whose variations are known to be normally distributed. Task groups involved with such test methods are referred to Practice E691 which contains preferable methods of analyzing data with those properties. 1.6 This practice is not intended to establish a method for estimating possible color-difference tolerances. 1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method with Multi-Valued Measurands