19.020 试验条件和规程综合 标准查询与下载

T/CSEE 0280-2021 中压柔性直流配电网成套设计规范

本文件规定了±1.5 kV～±50 kV 中压柔性直流配电网成套设计的总体要求、设计条件、设计要 求、过电压与绝缘配合、一次设备参数及要求、换流站控制保护系统、与低压直流电网的接口和辅助 系统要求。 本文件适用于基于模块化多电平换流器结构的柔性直流配电网的系统研究与成套设计，不包括直 流线路和接地极线路设计的内容，其他拓扑结构的柔性直流配电工程可参考执行。对于某些工程特殊 的要求，可根据具体的功能规范在此标准的基础上进一步研究确定。

Design code for complete set of medium voltage flexible DC distribution network

T/CSEE 0081.22-2021 统一潮流控制器（UPFC） 第 22 部分：电压源型换流器技术规范

本文件规定了统一潮流控制器电压源型换流器的使用条件、组成、技术要求、试验、铭牌，以及 包装、运输和贮存要求。 本文件适用于 220 kV 及以上电压等级的模块化多电平统一潮流控制器电压源型换流器，其他电压 等级和拓扑统一潮流控制器电压源型换流器参照使用。

Unified power flow controller (UPFC) — Part 22：Technical specification for VSC

T/CSEE 0081.01-2021 统一潮流控制器（UPFC） 第1部分：术语

本文件规定了统一潮流控制器（UPFC）相关术语和定义，以及符号和缩略语。 本文件适用于 220 kV 及以上电压等级采用模块化多电平换流器（MMC）的 UPFC，其他电压等级 或形式的 UPFC 术语可参照执行。

Unified Power Flow Controller (UPFC) Part 1: Terminology

T/CSEE 0241.6-2021 柔性直流电网 第6部分：建模技术导则 机电暂态模型

本文件规定了电力系统稳定分析计算用的柔性直流电网机电暂态仿真数学模型的建立、参数校核 试验及建模报告编写要求。 本文件适用于采用以 IGBT（绝缘栅双极型晶体管）等双向可控电力电子器件为核心换流元件的模 块化多电平电压源型换流器，直流对地电压±100 kV 及以上的高压直流电网的机电暂态建模，不适用 于采用电流源型换流器的高压直流输电系统。 本文件建立的模型不用于分析三相不对称故障。电压等级低于 100 kV 和非模块化多电平电压源型 换流器建模可参考本文件。

Flexible DC Grids Part 6: Modeling Technical Guidelines Electromechanical Transient Models

T/SZTIC 002-2021 保健食品中非法添加物的快速检测直接离子化小型质谱法

一、方法原理 样品经由萃取液震荡提取后，使用便携式质谱仪进行检测，仪器软件将测试结果与内置标准谱图库中的 31种保健品进行匹配计算，对测试结果进行判定：显示测试结果并判定阴性或阳性。 二、试剂材料 2.1装有萃取液（乙醇:乙腈:甲酸=180:20:1）滴瓶 2.2 500μl EP管 2.3 0.22μm有机尼龙滤膜 2. 4 取样勺 三、样品制备 使用一次性取样勺取一勺样品置于萃取液中，使用涡旋振荡仪振1min或者大力摇匀1min；然后将萃取液 从滴瓶挤压过0.22μm有机尼龙膜于500μlEP管中。 四、分析步骤 4.1 打开电源开机，打开分子泵抽5min左右； 4.2 固定好毛细柱，固定好空白试剂，清洁5次，然后更换待测样品清洁10次； 3. 3 选择保健品药品检测，选择类别，样品编号，然后启动测试，待分析结束，即可查阅结果； 五、结果判定 仪器软件将测试结果与内置标准谱图库中的31种保健品进行匹配计算，对测试结果进行判定：显示测试 结果并判定阴性或阳性。 六、比对试验数据 快速检测方法与对应项目涉及的国家标准、行业标准或者经验证的规范方法所测结果的一致性比较实验 数据。

Rapid detection of illegal additives in health food by direct ionization miniature mass spectrometry

T/DJPEC 0022-2021 制冷机用水性醇酸树脂涂料（底、面复合涂层）的检验标准

本文件规定了制冷机用水性醇酸树脂涂料（底、面复合涂层）的要求、检验方法和检验规则。

Inspection standards for water-based alkyd resin coatings (bottom and surface composite coatings) for refrigerators

DB50/T 1127-2021 食品快速检测实验室技术规范

本文件适用于食品（含食用农产品）批发市场、零售市场等市场开办者的自建食品快速检测实验室和市场监管部门设立的食品快速检测实验室。其他环节、场所、部门的食品快速检测实验室建设可参照执行

Technical specification for rapid food testing laboratory

DB50/T 1126-2021 食品快速检测实验室建设指南

本文件适用于食品（含食用农产品）批发市场、零售市场等市场开办者的自建食品快速检测实验室和市场监管部门设立的食品快速检测实验室。其他环节、场所、部门的食品快速检测实验室建设可参照执行。

Guidelines for the Construction of Food Rapid Testing Laboratories

T/QDAS 071-2021 光触媒壁纸有害物质净化性能

本文件规定了光触媒壁纸对室内空气中有害物质甲醛、甲苯净化性能的术语和定义、原理、技术要求、试剂和材料、试验仪器和装置、试验步骤、试验报告。 本文件适用于光触媒壁纸，具有空气净化性能的壁布、天花板等装饰装修材料可参照本标准。

Purificatory performance of harmful substances in photocatalyst wallpaper

ASTM D6659-16(2021) 物理和化学试验用湿蓝色和湿白色的取样和制备的标准实施规程

1.1 This practice covers the sampling and preparation of Wet Blue and Wet White for physical and chemical tests. The product is grouped into lots that are randomly sampled in such a manner as to produce a representative sample of the lot. This sample may be used to determine compliance of the lot with applicable specification requirements, and on the basis of results, the lot may be accepted or rejected in its entirety. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Sampling and Preparation of Wet Blue and Wet White for Physical and Chemical Tests

T/QGCML 159-2021 安全帽耐熔融金属飞溅测试仪校准方法

本文件规定了安全帽耐熔融金属飞溅测试仪的条件、校准仪器设备、校准结果等。 本文件适用于安全帽耐熔融金属飞溅测试设备的校准。

Calibration method of helmet splash resistance molten metal splash tester

T/CSTM 00363-2021 自冷涂层材料散热性能检测及评定方法

本文件规定了自冷涂层材料散热性能的检测及评定的原理、仪器和设备、检测条件、试验准备、检测步骤、试验数据处理、检测报告、评定方法等。 本文件适用于自冷涂层材料（以下称涂料）的检测与评定。

Test and evaluation method for heat dissipation performance of self-cooling coating materials

LST EN IEC 60216-3:2021 电绝缘材料 耐热性能 第3部分：计算耐热特性的说明（IEC 60216-3:2021）

Electrical insulating materials - Thermal endurance properties - Part 3: Instructions for calculating thermal endurance characteristics (IEC 60216-3:2021)

T/SHFCA 002-2021 化妆品稳定性试验指导原则

1 范围 2 规范性引用文件 3 分类 4 试验要求 5 试验方法 6 稳定性结果评价 附录A  (规范性附录)  影响因素试验方法 附录B  (规范性附录）加速试验方法 附录C  (规范性附录）长期试验方法

Guidelines for Stability testing of cosmetic

T/GAMA 20-2021 增材制造 高分子材料形状记忆驱动方法 紫外光热驱动法

增材制造高分子材料形状记忆紫外光热驱动方法

Additive manufacturing—Driving method for shape memory of polymer materials —UV thermal driving method

GSO OIML D30:2021 ISO/IEC 17025在法制计量检测实验室评估中的应用指南

This Document is applicable to all testing laboratories involved in legal metrology and in particular to those involved in type evaluation tests and examinations.

Guide for the application of ISO/IEC 17025 to the assessment of Testing Laboratories involved in legal metrology

ASTM E2008-17(2021) 用热重分析法测定挥发率的标准试验方法

1.1 These test methods cover procedures for assessing the volatility of solids and liquids at given temperatures using thermogravimetry under prescribed experimental conditions. Results of these test methods are obtained as volatility rates expressed as mass per unit time. Rates ≥5 µg/min are achievable with these test methods. 1.2 Temperatures typical for these test methods are within the range from 25 °C to 500 °C. This temperature range may differ depending upon the instrumentation used. 1.3 These test methods are intended to provide a value for the volatility rate of a sample using a thermogravimetric analysis measurement on a single representative specimen. It is the responsibility of the user of these test methods to determine the need for and the number of repetitive measurements on fresh specimens necessary to satisfy end use requirements. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Volatility Rate by Thermogravimetry

GSO ASTM E177:2021 ASTM 测试方法中术语“精度”和“偏差”的使用标准实践

-

Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods

GSO IEC TS 60216-7-1:2021 电绝缘材料 耐热性能 第7-1部分：使用分析测试方法 (RTEA) 加速测定相对耐热性能 基于活化能的计算说明

IEC TS 60216-7-1:2015(E) describes the procedure for the evaluation of the thermal endurance of electrical insulating materials, based on thermal analysis methods for the evaluation of the activation energy of the thermal degradation reaction and a conventional life test providing a life point in the thermal endurance graph. The purpose of the test procedure is to estimate the relative temperature index (RTE).

Electrical insulation materials - Thermal endurance properties - Part 7-1: Accelerated determination of relative thermal endurance using analytical test methods (RTEA) - Instructions for calculations based on activation energy

ASTM D7235-21 使用相关ASTM标准实践在分析仪和主要试验方法结果之间建立线性相关关系的标准指南

1.1?This guide covers a general methodology to develop and assess the linear relationship between results produced by a total analyzer system versus the results produced by the corresponding primary test method (PTM) that the analyzer system is intended to emulate, using the pri

Standard Guide for Establishing a Linear Correlation Relationship Between Analyzer and Primary Test Method Results Using Relevant ASTM Standard Practices