共找到 2159 条与 无损检测 相关的标准,共 144 页
Non-destructive testing — Leak testing — Radioactive tracer methods for pressured vessels and underground pipelines
Non-destructive testing. Ultrasonic guided-wave testing using the phased-array technique
Technical Specifications for Nondestructive Detection of Deep Road Defects with Ground-Penetrating Radar
本文件规定了玻璃幕墙抗渗检测装置的术语和定义、结构组成、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于玻璃幕墙抗渗检测装置的生产和检验。
Glass curtain wall impermeability detection device
本文件规定了便携式焊缝检测装置的组成及结构、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于便携式焊缝检测装置的设计及检验。
Portable weld inspection device
本文件规定了无损检测渗透探伤系统的设计原则、功能要求、系统管理和系统运维要求。 本文件适用于无损检测渗透探伤系统(以下简称系统)的设计、应用和管理。
Technical specifications for non-destructive testing and penetrant testing systems
近年来,钢壳混凝土结构在建筑工程应用越来越广泛,而钢壳混凝土脱空是影响其结构质量的重要原因。因此,钢壳混凝土脱空检测对保证钢壳混凝土结构的工程质量具有重要意义。本标准在阐述冲击弹性波检测钢壳混凝土脱空原理的基础上,对使用该方法进行脱空检测时涉及的检测设备、检测步骤、检测数据的整理及分析、检测结论、检测报告的编制进行了规定。
Technical specification for testing steel shell concrete by impact elastic wave method
Non-destructive testing — Ultrasonic guided-wave testing using the phased-array technique
Non-destructive testing — Ultrasonic testing — Vocabulary
本文件规定了莫来石纤维复合材料胶接界面太赫兹无损检测的术语和定义、方法原理、一般要求、检测设备、检测步骤、数据处理、检测结果及评价、检测记录和检测报告。 本文件适用于莫来石纤维复合材料胶接界面太赫兹无损检测,其他非金属材料的多胶接结构胶接界面的太赫兹时域光谱检测也可参照使用。
Nondestructive testing- Bonding interface of mullite fiber composites- Terahertz time-Domain spectroscopy detection method
Standard Practice for Instrumented Indentation Testing
Non-destructive testing — Acoustic emission testing — Metallic pressure equipment
Non-destructive testing — Ultrasonic testing — Characterization and sizing of discontinuities
BS EN ISO 18081. Non-destructive testing. Acoustic emission testing (AT). Leak detection by means of acoustic emission
Radiographic testing for welded joints in titanium
Non-destructive testing — Standard test method for determining residual stresses by neutron diffraction
Non-destructive testing of acoustic emission detection and evaluation methods for normal pressure metal storage tanks
本文件主要技术内容为无损检测中超声检测所用耦合剂的性能指标检测方法,文件规定了耦合剂的外观、颜色、气味、密度、黏度、挥发性及残留物、声速、声衰减、声阻抗、接触角、摩擦系数、凝点、闪点、pH值、腐蚀性等性能的检测方法,包括检测概述、设备器具、环境、样品、检测步骤、报告内容和检测精密度。
Method for testing the performance of couplant for ultrasonic testing of metal materials
1.1 This practice covers the manufacturing characterization of computed radiography (CR) systems, consisting of a particular phosphor imaging plate (IP), scanner, software, scanner operational parameters, and an image display monitor, in combination with specified metal screens for industrial radiography. 1.2 The practice defines system tests to be used to characterize the systems of different suppliers and make them comparable for users. 1.3 This practice is intended for use by manufacturers of CR systems or certification agencies to provide quantitative results of CR system characteristics for nondestructive testing (NDT) user or purchaser consumption. Some of these tests require specialized test phantoms to ensure consistency of results among suppliers or manufacturers. These tests are not intended for users to complete, nor are they intended for long term stability tracking and lifetime measurements. However, they may be used for this purpose, if so desired. Practice E2445 describes tests which are intended for users to observe the CR performance and test the long term stability. 1.4 The CR system performance is described by the basic spatial resolution, contrast, signal and noise parameters, and the equivalent penetrameter sensitivity (EPS). Some of these parameters are used to compare with DDA characterization and film characterization data (see Practice E2597 and Test Method E1815 ). Note 1: For film system characterization, the signal is represented by the optical density of 2 (above fog and base) and the noise as granularity. The signal-to-noise ratio is normalized by the aperture (similar to the basic spatial resolution) of the system and is part of characterization. This normalization is given by the scanning circular aperture of 100 µm of the micro-photometer, which is defined in Test Method E1815 for film system characterization. 1.5 The measurement of CR systems in this practice is restricted to a selected radiation quality to simplify the procedure. The properties of CR systems will change with radiation energy but not the ranking of CR system performance. Users of this practice may carry out the tests at different or additional radiation qualities (X-ray or gamma ray) if required. 1.6 The values stated in SI are to be regarded as the standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Practice for Manufacturing Characterization of Computed Radiography Systems
Non-destructive testing — Radiation methods for computed tomography — Part 4: Qualification
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号