19.100 无损检测 标准查询与下载
共找到 2159 条与 无损检测 相关的标准，共 144 页
Non-destructive testing - Acoustic emission testing - In-service acoustic emission monitoring of metallic pressure equipment and structures - General requirements
- ICS
- 19.100
- CCS
- 发布
- 2020-12-00
- 实施
1 Scope This document describes the test method for determining residual stresses in polycrystalline materials by neutron diffraction . It is applicable to both homogeneous and inhomogeneous materials including those containing distinct phases. The principles of the neutron diffraction technique are outlined. Suggestions are provided on : — the selection of appropriate diffracting lattice planes on which measurements should be made for different categories of materials, — the specimen directions in which the measurements should be performed, and — the volume of material examined in relation to the material grain size and the envisaged stress state. Procedures are described for accurately positioning and aligning test pieces in a neutron beam and for precisely defining the volume of material sampled for the individual measurements. The precautions needed for calibrating neutron diffraction instruments are described. Techniques for obtaining a stress-free reference are presented. The methods of making individual measurements by neutron diffraction are described in detail. Procedures for analysing the results and for determining their statistical relevance are presented. Advice is provided on how to determine reliable estimates of residual stresses from the strain data and on how to estimate the uncertainty in the results.
Non-destructive testing. Standard test method for determining residual stresses by neutron diffraction
- ICS
- 19.100
- CCS
- 发布
- 2020-11-30
- 实施
- 2020-11-30
Non-destructive testing — Infrared thermographic testing — General principles
- ICS
- 19.100
- CCS
- 发布
- 2020-11-11
- 实施
Non-destructive testing — Infrared thermographic testing — General principles
- ICS
- 19.100
- CCS
- 发布
- 2020-11-11
- 实施
本文件规定了开放式一体化智能运动测控平台的术语和定义、平台系统构成与分类、要求和检测方法。
Technical specifications of open integrated intelligent motion measurement and control platform
- ICS
- 19.100
- CCS
- M732
- 发布
- 2020-11-09
- 实施
- 2020-11-09
本文件规定了开放式一体化智能运动测控平台的术语和定义、接口技术要求。
Technical interface specifications of open integrated intelligent motion measurement and control platform
- ICS
- 19.100
- CCS
- M732
- 发布
- 2020-11-09
- 实施
- 2020-11-09
本文件规定了开放式一体化智能运动测控平台的术语和定义、检测方法。
Testing method of open integrated intelligent motion measurement and control platform
- ICS
- 19.100
- CCS
- M732
- 发布
- 2020-11-09
- 实施
- 2020-11-09
Non-destructive testing – Characterization and verification of ultrasonic test equipment – Part 3: Combined equipment (ISO 22232-3:2020)
- ICS
- 19.100
- CCS
- 发布
- 2020-11-04
- 实施
- 2020-11-04
Non-destructive testing – Characterization and verification of ultrasonic test equipment – Part 3: Combined equipment
- ICS
- 19.100
- CCS
- 发布
- 2020-11-04
- 实施
- 2020-11-04
Non-destructive testing - Characterization and verification of ultrasonic test equipment - Part 1: Instruments (ISO 22232-1:2020)
- ICS
- 19.100
- CCS
- 发布
- 2020-11-00
- 实施
- 2020-11-01
Non-destructive testing - Characterization and verification of ultrasonic test equipment - Part 2: Probes (ISO 22232-2:2020)
- ICS
- 19.100
- CCS
- 发布
- 2020-11-00
- 实施
- 2020-11-01
What is ISO 22232-2 about? ISO 22232-2 is the second part of the ISO 2223-2 series of standards that specifies the characteristics of probes. The probe is used for non-destructive ultrasonic testing in the following categories with center frequencies in the range of 0,5 MHz to 15 MHz, focusing or without focusing means: Single-or dual-transducer contact probes generating longitudinal and/or transverse waves Single-transducer immersion probes
Non-destructive testing. Characterization and verification of ultrasonic test equipment - Probes
- ICS
- 19.100
- CCS
- 发布
- 2020-10-31
- 实施
- 2020-10-31
Non-destructive testing - Characterization and verification of ultrasonic test equipment - Part 1: Instruments (ISO 22232-1:2020)
- ICS
- 19.100
- CCS
- 发布
- 2020-10-30
- 实施
- 2020-10-30
This document specifies methods, tolerances and acceptance criteria for verifying the performance of combined ultrasonic test equipment (i.e. instrument, probes and cables connected) by the use of appropriate standard calibration blocks. These methods are specifically intended for manual test equipment, i.e. ultrasonic instruments according to ISO 22232-1, and for manual ultrasonic non-destructive testing with single- or dual-transducer probes according to ISO 22232-2. This document is also applicable for multi-channel instruments. For automated test equipment, different tests can be needed to ensure satisfactory performance. The specified methods are intended for the use by operators working under site or shop floor conditions. These methods are not intended to prove the suitability of the equipment for particular applications. This document excludes ultrasonic instruments for continuous waves. This document also excludes ultrasonic phased array systems, see e. g. ISO 18563-3. If a phased array instrument is used in combination with single- or dual-transducer probes, this document is applicable to this combination.
Non-destructive testing - Characterization and verification of ultrasonic test equipment - Part 3: Combined equipment (ISO 22232-3:2020)
- ICS
- 19.100
- CCS
- 发布
- 2020-10-28
- 实施
- 2021-01-31
This document specifies methods, tolerances and acceptance criteria for verifying the performance of combined ultrasonic test equipment (i.e. instrument, probes and cables connected) by the use of appropriate standard calibration blocks. These methods are specifically intended for manual test equipment, i.e. ultrasonic instruments according to ISO 22232-1, and for manual ultrasonic non-destructive testing with single- or dual- transducer probes according to ISO 22232-2. This document is also applicable for multi-channel instruments. For automated test equipment, different tests can be needed to ensure satisfactory performance. The specified methods are intended for the use by operators working under site or shop floor conditions. These methods are not intended to prove the suitability of the equipment for particular applications. This document excludes ultrasonic instruments for continuous waves. This document also excludes ultrasonic phased array systems, see e. g. ISO 18563-3. If a phased array instrument is used in combination with single- or dual-transducer probes, this document is applicable to this combination.
Non-destructive testing — Characterization and verification of ultrasonic test equipment — Part 3: Combined equipment
- ICS
- 19.100
- CCS
- 发布
- 2020-10-16
- 实施
This document specifies the characteristics of probes used for non-destructive ultrasonic testing in the following categories with centre frequencies in the range of 0,5 MHz to 15 MHz, focusing or without focusing means: a) single- or dual-transducer contact probes generating longitudinal and/or transverse waves; b) single-transducer immersion probes. Where material-dependent ultrasonic values are specified in this document they are based on steels having a sound velocity of (5 920 ± 50) m/s for longitudinal waves, and (3 255 ± 30) m/s for transverse waves. This document excludes periodic tests for probes. Routine tests for the verification of probes using on-site procedures are given in ISO 22232-3. If parameters in addition to those specified in ISO 22232-3 are to be verified during the probe's life time, as agreed upon by the contracting parties, the procedures of verification for these additional parameters can be selected from those given in this document. This document also excludes ultrasonic phased array probes, therefore see ISO 18563-2.
Non-destructive testing - Characterization and verification of ultrasonic test equipment - Part 2: Probes (ISO 22232-2:2020)
- ICS
- 19.100
- CCS
- 发布
- 2020-09-30
- 实施
- 2020-12-31
本标准规定了电磁测量磁悬液浓度的原理、测量要求、操作方法、检测结果的判定、人员资格等内容和要求。 本标准适用于磁悬液浓度的实时、快速检测。
Non-destructive testing-The electromagnetic method for measuring magnetic particle suspension concentration
- ICS
- 19.100
- CCS
- M745
- 发布
- 2020-09-25
- 实施
- 2020-09-25
本标准规定了凸曲面斜入射试块的尺寸、材料、制造以及用它对超声检测设备进行校准和校验的使用方法。 本标准适用于空心类锻件、管件或棒类件等的周向方向斜入射超声波探伤水平、垂直、声程的精确定位。本标准提供了一种可以对周向斜探测凸曲面锻件角度、声速及零点标定的方法。
Non-destructive testing – Ultrasonic testing –Fabrication and testing method of oblique incident test block with convex surface
- ICS
- 19.100
- CCS
- M745
- 发布
- 2020-09-25
- 实施
- 2020-09-25
This document describes the test method for determining residual stresses in polycrystalline materials by neutron diffraction. It is applicable to both homogeneous and inhomogeneous materials including those containing distinct phases. The principles of the neutron diffraction technique are outlined. Suggestions are provided on: — the selection of appropriate diffracting lattice planes on which measurements should be made for different categories of materials, — the specimen directions in which the measurements should be performed, and — the volume of material examined in relation to the material grain size and the envisaged stress state. Procedures are described for accurately positioning and aligning test pieces in a neutron beam and for precisely defining the volume of material sampled for the individual measurements. The precautions needed for calibrating neutron diffraction instruments are described. Techniques for obtaining a stress-free reference are presented. The methods of making individual measurements by neutron diffraction are described in detail. Procedures for analysing the results and for determining their statistical relevance are presented. Advice is provided on how to determine reliable estimates of residual stresses from the strain data and on how to estimate the uncertainty in the results.
Non-destructive testing - Standard test method for determining residual stresses by neutron diffraction (ISO 21432:2019)
- ICS
- 19.100
- CCS
- 发布
- 2020-09-23
- 实施
- 2020-12-31
This document specifies the characteristics of probes used for non-destructive ultrasonic testing in the following categories with centre frequencies in the range of 0,5 MHz to 15 MHz, focusing or without focusing means: a) single- or dual-transducer contact probes generating longitudinal and/or transverse waves; b) single-transducer immersion probes. Where material-dependent ultrasonic values are specified in this document they are based on steels having a sound velocity of (5920 ± 50) m/s for longitudinal waves, and (3255 ± 30) m/s for transverse waves. This document excludes periodic tests for probes. Routine tests for the verification of probes using on- site procedures are given in ISO 22232-3. If parameters in addition to those specified in ISO 22232-3 are to be verified during the probe’s life time, as agreed upon by the contracting parties, the procedures of verification for these additional parameters can be selected from those given in this document. This document also excludes ultrasonic phased array probes, therefore see ISO 18563-2.
Non-destructive testing — Characterization and verification of ultrasonic test equipment — Part 2: Probes
- ICS
- 19.100
- CCS
- 发布
- 2020-09-18
- 实施
