19.100 无损检测 标准查询与下载

EN ISO 22232-1:2020 无损检测 超声检测设备的性能与检验 第1部分:仪器

This document specifies methods and acceptance criteria within the frequency range of 0,5 MHz to 15 MHz, for assessing the electrical performance of digital ultrasonic instruments for pulse operation using A-scan display, for manual ultrasonic non-destructive testing with single- or dual-transducer probes. This document is also applicable for multi-channel instruments. This document can partly be applicable to ultrasonic instruments in automated systems, but other tests can be needed to ensure satisfactory performance. This document excludes ultrasonic instruments for continuous waves. This document also excludes ultrasonic phased array instruments, see e.g. ISO 18563-1. If a phased array instrument has dedicated connectors for single- or dual-transducer probes this document is applicable for these channels.

Non-destructive testing - Characterization and verification of ultrasonic test equipment - Part 1: Instruments (ISO 22232-1:2020)

BS ISO 23159:2020 非破坏性测试 工艺柱上的伽马射线扫描方法

What is  ISO 23159   about?        ISO 23159 is used for non-destructive testing by the gamma-ray scanning method for   troubleshooting and testing process columns in industries. ISO 23159 is applicable to the testing of all kinds of separation processes columns and pipes. This includes columns with different tray configurations and with packed beds .   The benefits, obtained from the application of the gamma-ray scanning method for problem-solving, are many folds, such as safety improvement, environment pollution prevention, and economic savings.  

Non-destructive testing. Gamma ray scanning method on process columns

ISO 22232-1:2020 无损检测 超声检测设备的性能与检验 第1部分:仪器

This document specifies methods and acceptance criteria within the frequency range of 0,5 MHz to 15 MHz, for assessing the electrical performance of digital ultrasonic instruments for pulse operation using A-scan display, for manual ultrasonic non-destructive testing with single- or dual-transducer probes. This document is also applicable for multi-channel instruments. This document can partly be applicable to ultrasonic instruments in automated systems, but other tests can be needed to ensure satisfactory performance. This document excludes ultrasonic instruments for continuous waves. This document also excludes ultrasonic phased array instruments, see e.g. ISO 18563-1. If a phased array instrument has dedicated connectors for single- or dual-transducer probes this document is applicable for these channels.

Non-destructive testing — Characterization and verification of ultrasonic test equipment — Part 1: Instruments

T/GDASE 0014-2020 《聚乙烯燃气管道电熔焊接接头相控阵超声检测》

本标准规定了聚乙烯燃气管道电熔焊接接头相控阵超声检测的术语和定义、一般要求、检测工艺、检测方法、检测程序、检测数据的分析及缺陷评定。 本标准适用于公称直径为40mm～400mm且公称壁厚为3.7mm~36.4mm的聚乙烯燃气管道电熔焊接接头的相控阵超声检测，其它尺寸可参考执行。

Phased Array Ultrasonic Testing of Electrofusion Welded Joints of Polyethylene Gas Pipelines

ASTM E803-20 确定 L/D的标准测试方法

1.1 This test method defines an empirical technique for the measurement of the effective collimation ratio, L/D, of neutron radiography beams. The technique is based upon analysis of a neutron radiographic image and is independent of measurements and calculations based on physical dimensions of the collimation system. The values derived by this technique should be more accurate than those based on physical measurements, particularly for poorly defined apertures. 1.2 This test method covers both the manufacture and use of the device to measure L/D ratios. 1.3 Neutron images for this method can be produced on radiographic film using an appropriate conversion screen as detailed in Guide E748 or a CR screen with appropriate neutron converter. The method has not been validated with images produced by digital detector arrays. 1.4 This test method only applies to neutron beam lines with cold or thermal neutron spectrums. 1.5 Units—The values stated in SI units are to be regarded as standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the L/D Ratio of Neutron Radiography Beams

ISO 23159:2020 无损检测.工艺柱上的γ射线扫描法

This document is used for non-destructive testing by the gamma ray scanning method for troubleshooting and testing process columns in industries. This document is applicable to the testing of all kinds of separation processes columns and pipes. This includes columns with different tray configurations and with packed beds.

Non-destructive testing — Gamma ray scanning method on process columns

T/CSTM 00269-2020 激光选区熔化制造结构 工业CT尺寸测量

本标准规定了使用X射线工业CT系统进行激光选区熔化制造结构尺寸测量的一般要求、工艺技术要求及质量控制要求。 本标准适用于激光选区熔化制造金属构件的工业CT尺寸测量，其他增材制造构件的工业CT尺寸测量可参照使用。

Computed tomography in dimensional measurement Of selective laser melting manufactured structures

T/CSTM 00268-2020 航空铸件射线数字成像检测

本标准规定了使用存储磷光成像板、数字探测器阵列进行航空铸件射线数字成像检测的一般要求、工艺技术要求及质量控制要求。 本标准适用于航空铸件的射线数字成像检测，其它行业可参照使用。

Digital radiography of aero castings

T/CSTM 00271.3-2020 民用飞机结构在役无损检测对比试块 第3部分：金属材料结构对比试块

本部分规定了民用飞机金属结构在役无损检测对比试块的一般要求、人工损伤的制作、测试、标识、管理和定期核查等内容。 本部分适用于民用飞机金属材料构件（包括接头、单层或多层蒙皮铆接/螺接、紧固件、厚板开孔和圆角类结构）的裂纹和腐蚀损伤的无损检测所用对比试块的设计、制作及质量控制。

Civilian aircraft structures reference blocks for in-situ non-destructive testing- Part 3: Reference blocks for metal structures

T/CSTM 00271.2-2020 民用飞机结构在役无损检测对比试块 第2部分：复合材料结构对比试块

本部分规定了民用飞机复合材料结构在役无损检测对比试块的一般要求、人工损伤的制作、测试、标识、管理和定期核查等内容。 本部分适用于民用飞机复合材料构件（包括层板、夹层和板-板胶接类结构）的分层、脱粘、冲击和蜂窝积液损伤的无损检测所用对比试块的设计、制作及质量控制。

Civilian aircraft structures reference blocks for in-situ non-destructive testing-Part 2: Reference blocks for composite structures

T/CSTM 00271.1-2020 民用飞机结构在役无损检测对比试块 第1部分：总则

本部分规定了民用飞机结构在役无损检测对比试块研制及使用维护过程中的最低要求。 本部分适用于民用飞机结构在役无损检测对比试块设计、制造及使用维护，不适用于无损检测标准试块。

Civilian aircraft structures reference blocks for in-situ non-destructive testing- Part 1: General

T/CSTM 00270-2020 复合材料夹芯结构制件 X射线数字成像检测

本标准规定了复合材料夹芯结构制件（含蜂窝芯、泡沫芯等）X射线数字成像检测的一般要求、详细要求及工艺控制等要求。 本标准适用于复合材料夹芯结构制件的X射线数字成像检测，其他材料制成的夹芯结构或外场原位X射线数字成像检测可参照使用。

X-Ray Digital Radiography for composite sandwich structure

ASTM E2445/E2445M-20 计算机放射摄影系统的性能评估和长期稳定性的标准实践

1.1 This practice describes the evaluation of Computed Radiography (CR) systems for industrial radiography. It is intended to ensure that the evaluation of image quality, as far as this is influenced by the CR system, meets the needs of users of this standard, and their customers, and enables process control and long-term stability of the CR system. 1.2 This practice specifies the fundamental parameters of CR systems to be measured to determine baseline performance, and to track the long term stability of the system. These tests are for applications up to 320 kV. When greater than 320 kV or when a gamma source is used, these tests may still be used to characterize a system, but may need to be modified as agreed between the user and cognizant engineering organization (CEO). 1.3 The CR system performance tests specified in this practice shall be completed upon acceptance of the system from the manufacturer and at intervals specified in this practice to monitor long term stability of the system. The intent of these tests is to monitor the system performance degradation and to identify when an action needs to be taken when the system degrades by a certain level. 1.4 The use of gauges provided in this standard is mandatory for each test. In the event these tests or gauges are not sufficient, the user, in coordination with the CEO shall develop additional or modified tests, test objects, gauges, or image quality indicators to evaluate the CR system. Acceptance levels for these ALTERNATE tests shall be determined by agreement between the user and CEO. 1.5 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Performance Evaluation and Long-Term Stability of Computed Radiography Systems

ASTM G138-12(2020)e1 用标准辐照度源校准光谱辐射计的标准试验方法

1.1 This test method covers the calibration of spectroradiometers for the measurement of spectral irradiance using a standard of spectral irradiance that is traceable to a national metrological laboratory that has participated in intercomparisons of standards of spectral irradiance. 1.2 This method is not limited by the input optics of the spectroradiometric system. However, choice of input optics affects the overall uncertainty of the calibration. 1.3 This method is not limited by the type of monochromator or optical detector used in the spectroradiometer system. Parts of the method may not apply to determine which parts apply to the specific spectroradiometer being used. It is important that the choice of monochromator and detector be appropriate for the wavelength range of interest for the calibration. Though the method generally applies to photodiode array detector based systems, the user should note that these types of spectroradiometers often suffer from stray light problems and have limited dynamic range. Diode array spectroradiometers are not recommended for use in the ultraviolet range unless these specific problems are addressed. 1.4 The calibration described in this method employs the use of a standard of spectral irradiance. The standard of spectral irradiance must have known spectral irradiance values at given wavelengths for a specific input current and clearly defined measurement geometry. Uncertainties must also be known for the spectral irradiance values. The values assigned to this standard must be traceable to a national metrological laboratory that has participated in intercomparisons of standards of spectral irradiance. These standards may be obtained from a number of national standards laboratories and commercial laboratories. The spectral irradiance standards consist mainly of tungsten halogen lamps with coiled filaments enclosed in a quartz envelope, though other types of lamps are used. Standards can be obtained with calibration values covering all or part of the wavelength range from 200 to 4500 nm. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.2 1 This test method is under the jurisdiction of ASTM Committee G03 on Weathering and Durability and is the direct responsibility of Subcommittee G03.09 on Radiometry. Current edition approved June 1, 2020. Published July 2020. Originally approved in 1996. Last previous edition approved in 2012 as G138 – 12. DOI: 10.1520/ G0138-12R20E01. 2 Available from the CIE, (International Commission on Illumination), http:// www.techstreet.com/ciegate.tmpl CIE Central Bureau, Kegelgasse 27, A-1030 Vienna, Austria. Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Calibration of a Spectroradiometer Using a Standard Source of Irradiance

ASTM E999-20 控制工业射线照相胶片处理质量的标准指南

1.1 This guide2 establishes guidelines that may be used for the control and maintenance of industrial radiographic film processing equipment and materials. Effective use of these guidelines aids in controlling the consistency and quality of industrial radiographic film processing. 1.2 Use of this guide is limited to the processing of films for industrial radiography. This guide includes procedures for wet-chemical processes and dry processing techniques. 1.3 The necessity of applying specific control procedures such as those described in this guide is dependent, to a certain extent, on the degree to which a facility adheres to good processing practices as a matter of routine procedure. 1.4 If a nondestructive testing agency as described in Specification E543 is used to perform the examination, the testing agency should meet the requirements of Specification E543. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of federal and local codes prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Controlling the Quality of Industrial Radiographic Film Processing

ASTM E2075/E2075M-15(2020) 使用丙烯酸棒验证AE传感器响应的一致性的标准实践

1.1 This practice is used for routinely checking the sensitivity of acoustic emission (AE) sensors. It is intended to provide a reliable, precisely specified way of comparing a set of sensors, or telling whether an individual sensor’s sensitivity has degraded during its service life, or both. 1.2 This practice is not a “calibration” nor does it give frequency response information. 1.3 Units—The values stated in SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Verifying the Consistency of AE-Sensor Response Using an Acrylic Rod

ASTM E587-15(2020) 超声波角度接触测试标准实践

1.1 This practice covers ultrasonic examination of materials by the pulse-echo technique, using continuous coupling of angular incident ultrasonic vibrations. 1.2 This practice shall be applicable to development of an examination procedure agreed upon by the users of the practice. 1.3 The values stated in inch-pound units are regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Ultrasonic Angle-Beam Contact Testing

ASTM E242-15(2020) 放射照相0716图像为特定参数cb5f的标准参考放射照片改变

1.1 This document describes the appearance of a radiographic image where fundamental components of image quality are changed, that is, variables such as whether an X-ray or gamma ray source was used, the characteristics of the radiographic film (gradient, granularity, and developing conditions) and intensifying screens, and specimen thickness (the geometrical configuration of the radiographic set-up and focal spot size both affect image quality but are not considered in the reference radiographs). 1.2 The X-ray film systems used in obtaining the illustrative data were as follows: Very Fine Grain (comparable to class I of Test Method E1815) and Fine Grain (comparable to class II of Test Method E1815). 1.3 These reference radiographs2 consist of four composite illustrations3 and show how such factors as radiation energy, specimen thickness, and film properties affect the radiographic image. The reference radiograph films are an adjunct to this document and must be purchased separately from ASTM if needed. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Reference Radiographs for Appearances of Radiographic Images as Certain Parameters are Changed

JB/T 13937-2020 无损检测仪器 激光超声可视化检测仪

Non-destructive testing instrument laser ultrasonic visual detector

T/GDCKCJH 003-2019 承压特种设备现场金相检验技术导则

1、范围 2、规范性引用文件 3、术语和定义 考虑到相关标准规范没有对本标准一些关键术语具体定义，对 “现场金相检验”进行了解释。 4、金相检验人员 本章节对现场金相检验人员需要的基本知识、继续教育、资质做出规定。 5、相关设备 本章对现场金相检验的相关设备的资料和校准做出规定。 6、现场金相检验 规定了承压特种设备现场金相检验程序、检验前准备、检验部位选取、检测面磨制、检测面浸蚀、金相组织观察、现场复型或者现场金相组织图片采集、金相组织评定、出具检验报告等内容。 附录A现场金相显微镜的使用与维护 附录B承压特种设备现场金相检验流程 附录C常用现场金相化学浸蚀试剂 附录D常用现场金相电解浸蚀试剂

Technical Guide for On-site Metallographic Inspection of Special Pressure Equipment