21.060 紧固件 标准查询与下载

AECMA PREN 4066-1994 航空航天系列硼化钎焊填缝金属厚度25μm小于或等于a小于或等于100μm P.第1版

This standard specifies the dimensions and tolerances of filler metal for brazing, in borided foil, thickness 25 pm s a I 1 O0 pm, for aerospace applications.

Aerospace Series Filler Metal for Brazing Borided Foil Thickness 25 Micrometers Less Than or Equal to A Less Than or Equal to 100 Micrometer Dimensions Edition P1

AECMA PREN 4064-1994 航空航天系列钎焊填缝金属带厚度0,075mm小于或等于a小于或等于1,5mm P.第1版

This standard specifies the dimensions and tolerances of filler metal for brazing , in tape , thickness 0,075mm≤a≤1,5mm, for aerospace applications.

Aerospace Series Filler Metal for Brazing Tape Thickness 0,075 mm Less Than or Equal to a Less Than or Equal to 1,5 mm Dimensions Edition P1

AECMA PREN 4063-1994 航空航天系列钎焊填缝金属丝0,6mm小于或等于直径D小于或等于4mm P.第1版

This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies.

Aerospace Series Filler Metal for Brazing Wire Diameter 0,6 mm Less Than or Equal to D Less Than or Equal to 4 mm Dimensions Edition P1

CNS 4234-1991 不锈钢制螺钉及螺帽

本标准适用于由沃斯田、肥粒铁和麻田散组织之不锈钢制螺钉、螺帽，并须符合下列条件：（1）沃斯田镍铬钢和麻田散铬钢制螺钉、螺帽，其标称直径须在 1.6 至 39mm 之范围内。（2）肥粒铁铬制螺钉、螺帽，其标称直径在 1.6 至 14mm 之范围内。（3）使用 CNS 496 ~ 506 之公制螺

Screws and Nuts, Made of Stainless Steel

CNS 12210-1988 控制扭矩之高强度螺栓、六角螺帽及平垫圈组检验法

本标准规定控制扭矩之高强度螺栓、六角螺帽及平垫圈组（以下简称组）之检验法。

Method of Test for Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers

CNS 12209-1988 控制扭矩之高强度螺栓、六角螺帽及平垫圈组

本标准适用于控制扭矩之高强度螺栓，六角螺帽，及平垫圈组（以下简称组），其主要用于钢结构方面，并完全以结构件表面摩擦力结合。

Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers

CNS 11329-1985 摩擦接合用高强度六角螺栓、六角螺帽及平垫圈组合件检验法

本标准规定摩擦接合用高强度六角螺栓、六角螺帽及平垫圈组合件（以下简称组合件）之检验法。

Test Method for the Sets of High Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints

CNS 11328-1985 摩擦接合用高强度六角螺栓、六角螺帽及平垫圈组合件

本标准适用于摩擦接合用之高强度六角螺栓、六角螺帽，及平垫圈之组合件（以下简称组合件），其主要用于钢结构方面。

Sets of High Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints

CSN 02 1021-1984 耦合部件．支持面

Zpracovatel: ZVS - Zbrojovka Vsetín, koncernov? podnik Vsetín, pracovník — Bed?ich Lichnovsk? Oborové normaliza?ní st?edisko: Továrne strojárske j techniky, koncer-nov? v?skumn? ústav náradia VUNAR, Nové Zámky Pracovník Tj?adu pro normalizaci a mě?ení: Ing. Světlana Boro?ová

Coupling parts. Supporting surfaces

YB/T 039-1993 汽车车轮挡圈用热轧型钢

Hot rolled steel for automobile wheel retaining rings

YB/T 039-93 汽车车轮挡圈用热轧型钢

Hot rolled steel for automobile wheel retaining rings