21.060.01 紧固件综合 标准查询与下载

JIS B 1092:2006 紧固件.质量保证体系

この規格は，締結用部品の製造業者及び販売業者が対処する，締結用部品の品質保証システムに関する要求事項について規定する。これらの要求事項は。指定された特性をゼロ欠陥に近づける目的で，不適合締結用部品の製造を減らし，又は予防することを目指したものである。この規格は，原材料の受取りから製造工程を経て出荷までの，販売業者又は使用者の要求事項を示す。

Fasteners -- Quality assurance system

DLA A-A-59602 VALID NOTICE 1-2006 聚乙烯,聚四氟乙烯及聚酰胺制螺旋型覆套管

A-A-59602, dated 31 October 2000, has been reviewed and determined to be valid for use in acquisition.

TUBE, SPIRAL WRAP, POLYETHYLENE, POLYTETRAFLUOROETHYLENE AND POLYAMIDE

AIA/NAS NASM6812-2006 FSC 53一般用途60,000到125,000PSI铝抗腐蚀钢内螺纹合金钢紧固件

USE OF OR RELUNCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY AIA DOES NOT QUALIFY SUPPLIERS OR :ERTiFY CONFORMANCE OF ITEMS PROCURED UNDER NATIONAL AEROSPACE STANDARDS. UTABILITY OF ITEMS FOR

Fasteners, Externally Threaded Alloy Steel, Corrosion Resistant Steel, Aluminum 60,000 PSI to 125,000 PSI Rev 2

AIA/NAS NAS 3350-2006 Rev. 6高质量450及800华氏度自锁螺帽

This specification covers the requirements for high quality, self-locking nuts, used at temperatures up to 800°F, in conjunction with bolts and screws having Class 3A threads. These nuts are divided into classifications depending upon materials and room temperature axial tensile strength ratings as follows:

Nuts, Self-Locking, 450 Degrees F and 800 Degrees F, High Quality Rev 6

DLA A-A-59616 A-2006 125到150磅带螺纹的管装备钢铁和铝的拉把 锁和塞 取代DLA WW-P-471 C CANC NOTICE 2,DLA WW-P-471 C CANC NOTICE 1,DLA WW-P-471 C(1),DLA WW-P-471 C,DLA WW-P-471 B,DLA WW-P-471 A(2),

This CID covers the general requirements for pipe fittings: bushings, locknuts, and plugs; iron, steel, and aluminum; (threaded); 125 - 150 pounds. Pipe fittings: bushings, locknuts, and plugs; iron, steel, and aluminum; (threaded); 125 - 150 pounds. Pipe fittings covered by this CID are intended for commercial/industrial applications.

PIPE FITTINGS: BUSHINGS, LOCKNUTS, AND PLUGS; IRON, STEEL, AND ALUMINUM; (THREADED); 125 - 150 POUNDS [Superseded: DLA WW-P-471 C CANC NOTICE 2, DLA WW-P-471 C CANC NOTICE 1, DLA WW-P-471 C (1), DLA WW-P-471 C, DLA WW-P-471 B, DLA WW-P-471 A (2),

DLA A-A-59440 B-2006 NPTF-1型线铜螺杆遮断旋塞和旋塞注口的一般要求

This CID covers the general requirements for cocks, drain, cocks, plug, and cocks, shutoff, screw stem, brass, NPTF-1 threads are covered in the individual CID sheets. Cocks, drain, cocks, plug and cocks, shutoff, screw stem, brass, NPTF-1 threads covered by this CID are intended for commercial/industrial applications.

COCKS, DRAIN, COCKS, PLUG, AND COCKS, SHUTOFF, SCREW STEM, BRASS, NPTF-1 THREADS, GENERAL REQUIREMENTS FOR

GOST R 52643-2006 金属结构用高强度螺钉与螺母垫圈.通用规范

High-strength screws and nuts washers for metal structures. General specifications

AIA/NAS NASM16208-2006 Rev. 2FSC 5305.75KSI Ftu非磁性通用命名标准2A抗腐蚀钢打磨六角形头压力螺栓

BOLT, TENSION, HEXAGON HEAD, FINISHED, CORROSION RESISTANT STEEL, UNC-2A, NON-MAGNETIC, 75 KSI Ftu FSC 5305; REV. 2

BOLT, TENSION, HEXAGON HEAD, FINISHED, CORROSION RESISTANT STEEL, UNC-2A, NON-MAGNETIC, 75 KSI Ftu Rev 2

AIA/NAS NAS 1130-2006 Rev. 3.美国科学院 5340无带自锁自由运转螺纹螺旋绕嵌入物

uiameter of unthreided portlon Of shank shall not be lest chan min pitch dia nor

Insert, Screw Thread Helical Coil, Free Running and Self-Locking, Tangless FSC 5340; Rev 3

ASTM F1667-05 传动紧固件的标准规范:钉子、钉子和钉子

1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. Note 18212;Fastener ductility information is presented in Table 2 and dimensional information in tables 3-64.1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine.1.3 The values stated in inch-pound units are to be regarded as the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Driven Fasteners: Nails, Spikes, and Staples

NF E25-005:2005 紧固件.试验方法

Fasteners - Test methods.

BS EN 14399-1:2005 预加负荷用高强度结构螺栓组件.一般要求

This document specifies the general requirements for the components of bolt/nut/washer(s) assemblies for highstrength structural bolting, which are suitable for preloading, and for the assemblies themselves. Examples for components which fulfil the requirements of this document are specified in EN 14399-3, EN 14399-4, EN 14399-5 and EN 14399-6. NOTE For clauses of this document addressing the provisions of the EU Construction Products Directive, see Annex ZA.

High-strength structural bolting assemblies for preloading. General requirements

BS EN 14399-2:2005 预加负荷用高强度结构螺栓组件.预加负荷的适用性测试

This document specifies a tightening test to verify the suitability of high strength bolt/nut/washer assemblies for preloaded bolted connection in metallic structures. The purpose of this test is to check the behaviour of the fastener assembly so as to ensure that the required preload can be reliably obtained by the tightening methods specified in ENV 1090-1 with sufficient margins against over tightening and against failure.

High-strength structural bolting assemblies for preloading. Suitability test for preloading

DIN EN ISO 16047:2005 紧固件.扭矩/夹持力试验

This International Standard specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related pads. It is applicable, basically, to bolts, screws, studs and nuts made' of carbon steel and alloy steel, whose mechanical properties are specified in ISO 898-1, ISO 898-2 or ISO 898-6, having ISO metric threads with thread sizes M3 to M39. It is also applicable to the combination of other externally and internally threaded fasteners with a triangular ISO thread according to ISO 68-1. It is not applicable to set screws and similar threaded fasteners that are not under tensile stresses, nor to screws which form their own mating thread or threaded fasteners having additional self-locking features. Unless otherwise agreed, the tests are carried out at room temperature. However, tests carried out under standard conditions are made at a temperature of 10 ~C to 35 ~C. This method allows determination of the tightening characteristics of threaded fasteners and related pads.

Fasteners - Torque/clamp force testing (ISO 16047:2005); English version of DIN EN ISO 16047

GSA A-A-410 REINST NOTICE 2-2005 螺纹板牙(英制圆形拼合)

DIE, THREAD CUTTING (ROUND, SPLIT, INCH SERIES)

DIE, THREAD CUTTING (ROUND, SPLIT, INCH SERIES)

AIR FORCE QPL-AMS-P-5510-01 (1)-2005 (华氏零下65度至160 度)I型 直螺纹管轴套的预包装

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department o

PACKING, PREFORMED, STRAIGHT THREAD TUBE FITTING BOSS, TYPE I HYDRAULIC (-65 DEGREES F TO 160 DEGREES F)

NF E25-801-1:2005 预加负荷用高强度结构螺栓组件.第1部分:一般要求

High-strength structural bolting assemblies for preloading - Part 1 : general requirements.

NF E25-801-2:2005 预加负荷用高强度结构螺栓组件.第2部分:预加载适用性试验

High-strength structural bolting assemblies for preloading - Part 2 : suitability test for preloading.

VDA 235-203-2005 螺纹连接性能，摩擦系数 - 以实际应用及安装为导向的检测

Thread connection properties, friction coefficient - application- and installation-oriented testing

AIR FORCE QPL-AMS-P-5510-01-2005 (华氏零下65度至160 度)I型 直螺纹管轴套的预包装

This list has been prepared for use by or for the Government in the acquisition of products covered by the subject non-Government standard and such listing of a product is not intended to and does not connote endorsement of the product by the Department o

PACKING, PREFORMED, STRAIGHT THREAD TUBE FITTING BOSS, TYPE I HYDRAULIC (-65 DEGREES F TO 160 DEGREES F)