21.060.01 紧固件综合 标准查询与下载

DLA MS21960 REV C VALID NOTICE 1-2005 内部轮毂三路集束装置螺栓

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BODY, CLUSTER FITTING, THREE-WAY, INTERNAL BOSS

DLA MS21950 REV B VALID NOTICE 1-2005 耀斑单端口通过集束装置螺栓

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

BOLT, CLUSTER FITTING SINGLE PORT THROUGH-FLARE

DLA AND10050 REV 21-2005 标准尺寸的垫片密封直螺纹轴套

This specification is approved for use by all Departments and Agencies of the Department of Defense.

BOSSES, STANDARD DIMENSIONS FOR GASKET SEAL STRAIGHT THREAD

CNS 4354-2005 螺钉与螺帽之加工精度及公差（特精级）

本标准适用于标称直径1mm至3mm之特精级螺钉与螺帽。其它直径之螺钉与螺帽，原则上亦可引用本标准。

Finishes and tolerances for product grade of screws and nuts

DLA FF-S-85 D-2005 六角形头插槽螺帽

The General Services Administration has authorized the use of this federal specification by all Federal agencies.

SCREW, CAP, SLOTTED AND HEXAGON HEAD

ASTM A540/A540M-05 特殊用途合金钢螺栓材料的标准规范

Standard Specification for Alloy-Steel Bolting Materials for Special Applications

BS EN ISO 16047:2005+A1:2012 紧固件. 扭矩/夹紧力试验

Fasteners - Torque/clamp force testing

EN ISO 16047:2005 紧固件.扭矩/夹持力试验 ISO 16047-2005

This International Standard specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts.It is applicable, basically, to bolts, screws, studs and nuts made of carbon steel and alloy steel, whose mechanical properties are specified in ISO 898-1 ISO 898-2 having ISO metric threads with thread sizes M3 to M39. It is also applicable to the combination of other externally and internally threaded fasteners with a triangular ISO thread according to ISO 68-1.It is not applicable to set screws and similar threaded fasteners that are not under tensile stresses, nor to screws which form their own mating thread .Unless othe

Fasteners - Torque/clamp force testing (ISO 16047:2005)

ISO 16047:2005 紧固件.扭矩/夹持力试验

This International Standard specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts. It is applicable, basically, to bolts, screws, studs and nuts made of carbon steel and alloy steel, whose mechanical properties are specified in ISO 898-1, ISO 898-2 or ISO 898-6, having ISO metric threads with thread sizes M3 to M39. It is also applicable to the combination of other externally and internally threaded fasteners with a triangular ISO thread according to ISO 68-1. It is not applicable to set screws and similar threaded fasteners that are not under tensile stresses, nor to screws which form their own mating thread or threaded fasteners having additional self-locking features. Unless otherwise agreed, the tests are carried out at room temperature. However, tests carried out under standard conditions are made at a temperature of 10 °C to 35 °C. This method allows determination of the tightening characteristics of threaded fasteners and related parts.

Fasteners - Torque/clamp force testing

DIN 918 Bb.3:2005 紧固件.欧洲标准.综述

Fasteners - European Standards - Survey

AIA/NAS NAS 9303-2005 Rev. 4.FSC 5320代号B及E,3级A式球状机械锁杆100度埋头空心柳钉

ADD LETTER “B” AFTER BASIC PART NUMBER TO INDICATE 5056 ALUMINUM ALLOY SLEEVE AND 8740 ALLOY STEEL SPINDLE.

Rivet-Blind, 100 Degree Flush Shear Head, Mechanically Locked Spindle, Bulbed Style A, Class 3, Code B and E FSC 5320; Rev 4

AIA/NAS NAS 1580-2005 Rev. 12FSC 5306,95KSI Fsu,楔榫槽十字形偏差100度埋头剪力螺栓

MARK W I T H MANUFACTURER'S SYMBOL (SYMBOL LOnATION OPTIONAL IN ANY SECTOR), GRIP DASH NUMBER AM) "D", WHEN APPLICABLE. (1) ""DL"" IDENTIFIES BOLT WITH DRILLED SHANK.

Bolt, Shear, 100 Degree Flush Head, Offset Cruciform and Covetail Slot, 95 KSI Fsu FSC 5306; Revision 12

AIA/NAS NAS 1990-2005 FSC 5306.Rev. 9,108KSI Fsu,楔榫开槽十字形偏差黄铜头保险螺栓

ALLOY STEEL - 4140 (UNS G41400) per MlL-S-5626,4340 (UNS G43400) per AMS6415

Bolt, Shear, Brazier Head, Offset Cruciform and Dovetail Slot, 108 KSI Fsu Rev. 9; FSC 5306

AIA/NAS NAS 1989-2005 FSC 5306.Rev. 9,108KSI Fsu,楔榫开槽十字形偏差黄铜头保险螺栓

ALLOY STEEL - 4140 (UNS G41400) per MlL-S-5626,4340 (UNS G43400) per AMS6415

Bolt, Shear, Brazier Head, Offset Cruciform and Dovetail Slot, 108 KSI Fsu Rev. 9; FSC 5306

AIA/NAS NAS 9302-2005 Rev. 4.FSC 5320代号B及E,2级A式球状机械锁杆100度埋头空心柳钉

NAS1202THRUNAS1210, "Bolt, 100 Deg. Close Tolerance Head and

Rivet-Blind, 100 Degree Flush Head, Mechanically Locked Spindle, Bulbed Style A, Class 2, Code B and E FSC 5320; Rev 4

AIA/NAS NAS 9304-2005 Rev. 4.FSC 5320代号B及E(特大型直径)1级B式球状机械锁杆100度埋头空心柳钉

ADD LETTER “B” AFTER BASIC PART NUMBER TO INDICATE 5056 ALUMINUM ALLOY SLEEVE AND 8740 ALLOY STEEL SPINDLE. ADD LETTER “E” AFTER BASIC PART NUMBER TO INDICATE 5056 ALUMINUM ALLOY SLEEVE AND PH15-7 Mo CRES OR A-286 CRES SPINDLE

Rivet-Blind, Protruding Head, Mechanically Locked Spindle, Bulbed Style B, Class 1, Code B and E (OVERSIZE DIAMETER) FSC 5320; Rev 4

AIA/NAS NAS 9305-2005 Rev. 4.FSC 5320代号B及E(特大型直径)2级B式球状机械锁杆100度埋头空心柳钉

RIVET-BLIND, 100° FLUSH HEAD, MECHANICALLY LOCKED SPINDLE, BULBED STYLE B, CLASS 2, CODE B AND E 4 (OVERSIZE DIAMETER)

Rivet-Blind, 100 Degree Flush Head, Mechanically Locked Spindle, Bulbed Style B, Class 2, Code B and E (OVERSIZE DIAMETER) FSC 5320; Rev 4

AIA/NAS NAS 9301-2005 Rev. 4.FSC 5320代号B及E,1级A式球状机械锁杆突出头空心柳钉

ADD LETTER “B” AFTER BASIC PART NUMBER TO INDICATE 5056 ALUMINUM ALLOY SLEEVE AND 8740 ALLOY STEEL SPINDLE.

Rivet-Blind, Protruding Head, Mechanically Locked Spindle, Bulbed Style A, Class 1, Code B and E FSC 5320; Rev 4

AIA/NAS NAS 1985-2005 FSC 5306.Rev. 9,108KSI Fsu,楔榫开槽十字形偏差黄铜头保险螺栓

ALLOY STEEL - 4140 (UNS G41400) per MlL-S-5626,4340 (UNS G43400) per AMS6415

Bolt, Shear, Brazier Head, Offset Cruciform and Dovetail Slot, 108 KSI Fsu Rev. 9; FSC 5306

AIA/NAS NAS 1986-2005 FSC 5306.Rev. 9,108KSI Fsu,楔榫开槽十字形偏差黄铜头保险螺栓

NAM13 12-105, “Fastener Test Methods Method 105 Stress Durability” was adopted on 29 August 1997 for use by the Department of Defense @OD). Proposed changes by DoD activities must be submitted to the DoD Adopting Activity: Commander, Naval Air Warfare Center Aircraft Division, Code 4141OOB120-3 Highway 547, Lakehurst, NJ 08733-5100. DoD activities may obtain copies of this standard fi-om the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 191 11-5094. The private sector and other Government agencies may purchase copies fi-om the Aerospace Industries Association, 1250 Eye Street NW, Washington, DC 20005.

Bolt, Shear, Brazier Head, Offset Cruciform and Dovetail Slot, 108 KSi Fsu Rev. 9; FSC 5306