共找到 1315 条与 螺母 相关的标准,共 88 页
Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012)
Hexagon thin nuts chamfered (style 0) - Product grades A and B (ISO 4035:2012)
Hexagon regular nuts (style 1) - Product grade C (ISO 4034:2012)
Hexagon regular nuts (style 1) with metric fine pitch thread - Product grades A and B (ISO 8673:2012)
Hexagon thin nuts unchamfered (style 0) - Product grade B (ISO 4036:2012)
Hexagon high nuts (style 2) - Product grades A and B (ISO 4033:2012)
Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012)
Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012)
Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012)
Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012)
Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012)
Hexagon high nuts (style 2) with metric fine pitch thread - Product grades A and B (ISO 8674:2012)
Hexagon thin nuts chamfered (style 0) with metric fine pitch thread - Product grades A and B (ISO 8675:2012)
Hexagon regular nuts (style 1) - Product grades A and B (ISO 4032:2012)
Included herein are complete general and dimensional specifications for metric and inch types of spring nuts recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw is considered adequate for the application. It should be noted that spring nuts having other configurations, dimensions, provisions for ground, etc., are available and manufacturers should be consulted.
Spring Nuts
Included herein are general, dimensional, and performance specifications for those typies, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement of the mating metal or plastic studs and in some cases screw or bolt threads if considered adequate for the fastening joint appalications. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the metric equivalent of this document, see SAE J892M.
Push-On Spring Nuts Inch Series General Specifications
Included herein are general, dimensional, and performance specifications for those typies, styles, and sizes of steel stamped Push-On Spring Nuts recognized as SAE standard. These nuts are intended for general use where the engagement of the mating metal or plastic studs and in some cases screw or bolt threads if considered adequate for the fastening joint appalications. It should be noted that Push-On Spring Nuts having other characteristics and configurations are available and manufacturers should be consulted. For the inch equivalent of this document, see SAE J892.
Push-On Spring Nuts Metric Series General Specifications
Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.
High and Low Crown (Blind, Acorn) Hex Nuts
Included herein are the detailed general and dimensional specifications applicable to high hex nuts. All general specifications not shown here shall conform with those applicable to hex thick nuts and hex thick slotted nuts appearing in ASME B18.2.2. High hex nuts are primarily intended for use in automotive and other ground-based vehicles and industrial equipment where a long length of hexagon is required for wrenching purposes.
Hexagon High Nuts
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE Standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.
Steel Stamped Nuts of One Pitch Thread Design Inch Series
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号