21.060.40 铆钉 标准查询与下载

AIA/NAS NASM83459/3-1998 FSC 5320型III类100度埋头钉95 KSI Fsu双金属材料钛铆钉

Rivet, Titanium, Bimetal, 95 KSI Fsu, 100 Degree Reduced Flush Crown Head, Type III FSC 5320

Rivet, Titanium, Bimetal, 95 KSI Fsu, 100 Degree Reduced Flush Crown Head, Type III

BS 7805-2:1997 环煅开槽铆钉.尺寸在12.7 mm至34.9 mm(含)之间的铆钉规范

This Part of BS 7805 specifies the materials of manufacture, hole diameter, the range of joint thickness and performance of installed swaged collar grooved rivets with nominal shank diameters from 12.7 mm to 34.9 mm inclusive, and either a round, truss or 90 °countersunk head.

Swaged collar grooved rivets - Specification for sizes from 12 - 7 mm up to and including 34.9 mm

KS B 1102-1996 热镦铆钉

이 규격은 열간으로 성형한 일반용, 보일러용 및 선박용 강제 리벳에 대하여 규정한다.

Hot headed rivets

BS 7855-1:1996 磨擦片衬里的附件用公制铆钉.半管状铆钉规范

This Part of BS 7855 specifies the dimensions and materials for semi-tubular rivets with nominal diameters from 3 mm up to and including 10 mm for the attachment of friction linings to support components for use in automotive or industrial applications. Rivets conforming to this standard are suitable for automatic or hand fed riveting systems. Annex A gives recommendations for the dimensional tolerances that are applicable to the rivet holes in friction linings and support components assembled together with rivets conforming to this standard. Annex B gives recommendations for the rivet clench conditions and dimensions that are applicable to installed rivets. Annex C gives recommendations that should be applied when riveted friction lining assemblies are reconditioned for further service use.

Metric rivets for the attachment of friction linings - Specification for semi-tubular rivets

BS 7805-1:1995 环煅开槽铆钉.直径尺寸达到(包括)10mm的规范

This Part of BS 7805 specifies the materials of manufacture, hole diameter, the range of joint thickness and performance of installed swaged collar grooved rivets with nominal shank diameters from 4.8 mm to 10 mm inclusive, and either a brazier, truss or countersunk head.

Swaged collar grooved rivets - Specification for sizes up to and including 10 mm diameter

JIS B 1214:1995 热镦制铆钉

この規格は，熱間で成形()した一般用，ボイラ用及び船用の鋼製のリべット(以下，リべットという。)について規定する。注()素材の変態点以上の温度で，塑性加工によって頭部を成形することをいい，熱間で，かしめ成形することを意味するものではない。

Hot headed rivets

JIS B 1213:1995 冷镦制铆钉

この規格は，一般に用いる冷間で成形()した鋼製のリべット(以下，鋼リべットという。)，黄銅製のリべット(以下，黄銅リべットという。)，銅製のリべット（以下，銅リべットという。)及びアルミニウム製のリべット(以下，アルミニウムリべットという。)について規定する。注()冷間で塑性加工によって頭部を成形することをいい，冷間で，かしめ成形することを意味するものではない。

Cold headed rivets

BS 4894:1993 通用开口铆钉规范(公制系列)

Specifies the materials and dimensions for oval and countersunk head bifurcated rivets with shank diameters 2mm to 5mm inclusive.

Specification for bifurcated rivets for general purpose use (metric series)

DIN 124:1993 圆头铆钉.公称直径10至36mm

The document contains dimensional and technical requirements of round head rivets and specifies their designation.

Steel round head rivets with nominal diameters from 10 to 36 mm

ARMY A-A-52123-1993 铆钉顶棒

The General Services Administration has authorized the use of this Carmercial Item Description in preference to MIL-B-920.

BARS, BUCKING, RIVET

ASTM A502-93 钢结构铆钉

1.1 This specification covers three grades of steel rivets in diameters from 1/2 to 1 1/2 in. (13 to 38 mm), inclusive, for structural fabricating purposes. The grades are as follows: 1.1.1 Grade 1 is a carbon steel rivet for general purposes. 1.1.2 Grade 2 is a carbon-manganese steel rivet suitable, with proper riveting technique, for use with high-strength carbon and high-strength low-alloy structural steels. 1.1.3 Grade 3 is similar to Grade 2 with enhanced atmospheric corrosion resistance and weathering characteristics comparable to that of steels in Specification A588/ A588M. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition (see 5.2). When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Steel Structural Rivets

EN 2553:1992 航空航天系列 铆钉，实心，100° 带圆顶的标准沉头，铝合金 2017A，英制系列

This standard specifies the characteristics of solid rivets, with 100° normal countersunk head with dome, inch based series, in aluminium alloy, for maximum operating temperature 120 °C

Aerospace series - Rivets, solid, 100° normal countersunk head with dome, in aluminium alloy 2017A, inch based series

EN 2146:1992 航空航天系列 铆钉，实心，通用头，铝合金 2017A，英制系列

This standard specifies the characteristics of solid rivets, with universal head, inch based series, in aluminium alloy, for maximum operating temperature 120 °C.

Aerospace series - Rivets, solid, universal head, in aluminium alloy 2017A, inch based series

CSN 02 2039-1992 两部分组成的铆钉．技术交付代码和尺寸

Zpracovatel: V?zkumn? ústav strojírenského spot?ebního zbo?í, Praha, I?O 010 529 — Ing. Jana Hanslíko-vá Pracovník Federálního ú?adu pro normalizaci a mě?ení: Ing. Zdeněk Kratochvíl

Two-part rivets. Technical delivery code and dimensions

KS R 4023-1991(2011) 制动器衬片的铆钉和汽车离合器摩擦片

RIVETS OF BRAKE LININGS AND CLUTCH FACINGS FOR AUTOMOBILES

DIN 65495-402:1990 航空航天.米制系列、铆钉材料3.1324、双剪切、压窝的、平头铆钉连接用静载荷铆钉设计值

Aerospace; rivet design values, static load, for flush head rivet joints, double shear, dimpled, rivet material 3.1324, metric series

DIN 65495-205:1990 航空航天.米制系列、铆钉材料2.4360、单剪切、压窝成形的、平头铆钉连接用静载荷铆钉设计值

Aerospace; rivet design values, static load, for flush head rivet joints, single shear, dimpled, rivet material 2.4360, metric series

DIN 65495-202:1990 航空航天.米制系列、铆钉材料3.1324、单剪切、压窝成形的、平头铆钉连接用静载荷铆钉设计值

The standard defines the breaking, shear and ultimate tensile loads on the individual rivet of universal rivet joints taking into account the rivet and component materials.#,,#

Aerospace; rivet design values, static load, for flush head rivet joints, single shear, dimpled, rivet material 3.1324, metric series

DIN 65495-401:1990 航空航天.米制系列、铆钉材料3.1124、双剪切、压窝成形的、平头铆钉连接用静载荷铆钉设计值

The standard defines the breaking, shear and ultimate tensile loads on the individual rivet of universal rivet joints taking into account the rivet and component materials.#,,#

Aerospace; rivet design values, static load, for flush head rivet joints, double shear, dimpled, rivet material 3.1124, metric series

DIN 65495-201:1990 航空航天.米制系列、铆钉材料3.1124、单剪切、压窝成形的、平头铆钉连接用静载荷铆钉设计值

Aerospace; rivet design values, static load, for flush head rivet joints, single shear, dimpled, rivet material 3.1124, metric series