21.060.40 铆钉 标准查询与下载

GOST 10304-1980 铆钉(B和C级).通用规范

Настоящий стандарт распространяется на заклепки общемашиностроительного применения, классов точности В и С, предназначенные для работы

Rivets classes B and C. General specifications

GOST 10303-1980 平头铆钉(B和C级).规范

Настоящий стандарт распространяется на заклепки с плоской головкой общемашиностроительного применения с диаметром стержня от 2 до 36 мм к

Flat-head rivets classes B and C. Specifications

GOST 10302-1980 扁半圆头铆钉.技术条件

Настоящий стандарт распространяется на заклепки с полукруглой низкой головкой общемашиностроительного применения с диаметром стержня о

Brazier-head rivets classes B and C. Specifications

GOST 10301-1980 半沉头铆钉.技术条件

Настоящий стандарт распространяется на заклепки с полупотайной головкой общемашиностроительного применения с диаметром стержня от 2 до 3

Round-top countersunk-head rivets classes B and C. Specifications

KS B 1103-1978 半管状铆钉

이 규격은 일반으로 사용되는 강제의 세미 튜우블러 리벳(이하 강리벳이라 한다) 황동제의 세

Semi - Tubular Rivets

SAE J1200-1977 抽芯铆钉 断裂心轴型

This standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly. A blind rivet is a blind fastener which has a self-contained mechanical, chemical, or other feature which permits the formation of an upset on the blind end of the rivet and expansion of the rivet shank during rivet setting to join the component parts of an assembly. Break mandrel blind rivets are pull mandrel-type blind rivets, where during the setting operation the mandrel is pulled into or against the rivet body and breaks at or near the junction of the mandrel shank and its upset end.

Blind Rivets - Break Mandrel Type

JIS B 1215:1976 半管型铆钉

この規格は，-般に用いる鋼製のセミチューブラリベット(以下，鋼リベットという。)，黄銅製のセミチューブラリベット(以下，黄銅りベットという。)，銅製のセミチューブラリベット(以下，銅りべートという。)及びアルミ=ウム製のセミチューブラリベット(以下，アルミ=ウムリべットという。)について規定する。ただし，JIS D 4312(自動車用ブレーキライニング及びクラッチフェーシングのリべット)に規定するセミチューブラリベットを除く。備考この規格で，鋼リベット，黄銅リベット，銅ベット及びアルミ=ウムリべットを総称する場合は，単にベットという。

Semi-tubular rivets

UNI 7345-1974 自攻铆钉．螺纹和端，取代UNI S242

Esempio e prospetto con designazione.

Tapping rivets. Thread and end.

UNI 7346-1974 圆头自攻铆钉，取代UNI S 241

Esempio e prospetto con designazione. Materiale: acciaio per stampaggio a freddo (vedere UNI 7323-74, parte 4), ovvero altro materiale.

Round head tapping rivets.

UNI 7347-1974 平钟形自攻铆钉

Esempio e prospetto con designazione. Materiale: acciaio per stampaggio a freddo (vedere UNI 7323-74, parte 4), ovvero altro materiale.

Countersunk (flat) head tapping rivets.

ASME B18.1.2-1972 大型铆钉

This standard covers complete general and dimensional data for those types of large solid rivets recognized as American National Standard together with dimensional data applicable to manufactured heads after driving, driven heads, and hold-on (dolly bar) and rivet set impressions. Also included are appendixes covering formulas on which dimensional data are based. It should be understood, however, that where questions arise concerning acceptance of product, the dimensions in the tables shall govern over recalculation by formula.

Large Rivets 1/2 Inch Nominal Diameter and Larger Revision of B18.4-1960

ASME B18.1.1-1972 小型实心铆钉

This standard covers complete general and dimensional data for those types of small solid rivets recognized as American National Standard . All other types of small solid rivets, within the limits of the diameters contained herein, are to be considered special. Also included is an appendix covering formulas on which dimensional data are based. It should be understood, however, that where questions arise concerning acceptance of product, the dimensions in the tables shall govern over recalculation by formula.

Small Solid Rivets 7/16 Inch Nominal Diameter and Smaller

ASME B18.7-1972 通用半空心铆钉，全空心铆钉，开口铆钉及铆钉帽

This standard covers complete general and dimensional data for semi-tubular rivets, full tubular rivets, split and rivet caps for use in general purpose applications. The products described are suitable for joining metallic and non-metallic materials or combinations thereof. It should be noted that while these products are suitable for general purpose assembly, other special purpose types are available to satisfy particular requirements and manufacturers should be consulted for special requirements. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Consumers are requested to consult with manufacturers concerning availability of products.

General purpose semi-tubular rivets, full tubular rivets, split rivets and rivet caps

ANSI/ASME B18.1.2-1972 大型铆钉(标称直径为1/2英寸及以上)

This standard covers complete general and dimensional data for those types of large solid rivets recognized as "American National Standard" together with dimensional data applicable to manufactured heads after driving, driven heads, and hold-on (dolly bar) and rivet set impressions. Also included are appendixes covering formulas on which dimensional data are based. It should be understood, however, that where questions arise concerning acceptance of product, the dimensions in the tables shall govern over recalculation by formula.

Large Rivets

ANSI/ASME B18.1.1-1972 小型实心铆钉(标称直经为7/16英寸及以下)

This standard covers complete general and dimensional data for those types of small solid rivets recognized as "American National Standard". All other types of small solid rivets, within the limits of the diameters contained herein, are to be considered special. Also included is an appendix covering formulas on which dimensional data are based. It should be understood, however, that where questions arise concerning acceptance of product, the dimensions in the tables shall govern over recalculation by formula.

Small Solid Rivets (7/16 Inch Nominal Diameter and Smaller)

BS 4620:1970 一般工程用铆钉规范

Dimensions, head shapes, and materials for rivets, in metric sizes for shank diameters ranging from 1 mm to 39 mm. Metric version of BS 275 and BS 1974.

Specification for rivets for general engineering purposes

CSN 02 2382-1969 管铆钉

Zpracovatel: ?roubárna ?atec, n. p., Zatec — Vladimír Prask Pracovník ??adu pro normalizaci a mě?ení: Ing. Lubomír Cechal

Tube rivets

CSN 02 2331-1967 中心钻孔平头铆钉

Zpracovatel: ?roubárna ?atec, n. p., ?atec. Pracovník ??adu pro normalizaci a mě?ení: Jan ?ák.

Centre-drilled flat head rivets

CSN 02 2300-1967 铆钉．调查

Zpracovatel: ?roubárna ?atec, n. p., ?atec. Pracovník ??adu pro normalizaci a mě?ení: Jan ?ák.

Rivets. Survey

CNS 567-1966 热作铆钉

本标准适用于一般用，锅炉用及船用之热作铆钉（以下简称铆钉）。

Hot Headed Rivet