21.060.50 销、钉 标准查询与下载
共找到 563 条与 销、钉 相关的标准，共 38 页
? ??? ?? ?? ?? ?? ?? ?? ?? ??? ????. ? ??? ?? ????
Longitudinal groove headless pin
- ICS
- 21.060.50
- CCS
- V20
- 发布
- 2005-11-17
- 实施
- 2005-11-17
Clevis pins and cotter pins(Inch series)
- ICS
- 21.060.50
- CCS
- 发布
- 2005-11-17
- 实施
? ??? ???? ?? ?? ?(?? ?)? ?? ?? ? ?? ?? ??? ??? ??
Clevis pins and cotter pins(Inch series)
- ICS
- 21.060.50
- CCS
- V20
- 发布
- 2005-11-17
- 实施
- 2005-11-17
? ??? ??? ???? ?? ? ??? ???? ?? ????? ??? ?? ??? ?
Coiled and slotted tubular spring pin
- ICS
- 21.060.50
- CCS
- V20
- 发布
- 2005-11-17
- 实施
- 2005-11-17
This Standard covers the complete dimensional and general data for metric series cotter (split) pins and two types, A and B, of headed and headless clevis pins intended for general applications and recognized as American National Standard. Type A clevis are without holes. Type B clevis pins specified herein are with holes intended for use with cotter pins; however, a means is provided to specify other hole sizes when required for use with other types of pins.
Cotter Pins, Headless Clevis Pins, and Headed Clevis Pins (Metric Series)
- ICS
- 21.060.50
- CCS
- J18
- 发布
- 2005-08-16
- 实施
この規格は，鋼製，オーステナイト系ステンレス鋼製及びマルテンサイト系ステンレス鋼製の重荷重用及び軽荷重用溝付きスプリングビン並びに重荷重用，一般用及び軽荷重用の二重巻きスプリングピン(以下，スブリングピンと総称する。)について規定する。
Spring pins
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2005-07-20
- 实施
この規格は，主として一般に使用される手打用くぎ及び自動くぎ打機用のくぎ()について規定する。ただし，自動くぎ打機用として連結するための材料及びその方法については規定しない。 注()自動くぎ打機用のくぎとは，プラスチック，紙，針金，のりなどを用いて連結されろくぎをいう。
Nails
- ICS
- 21.060.50
- CCS
- Y71
- 发布
- 2005-03-20
- 实施
1.1 This specification covers requirements for steel wire nails suitable for use in the application of gypsum board. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test method portion, Sections 7 and 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Nails for the Application of Gypsum Board
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2004
- 实施
1.1 This specification covers requirements for steel wire nails suitable for use in the application of gypsum board.1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.1.3 The values stated in inch-pound units are to be regarded as the standard.The following precautionary caveat pertains only to the test method portion, Sections , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Nails for the Application of Gypsum Board
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2004
- 实施
Nails - Technical delivery regulations
- ICS
- 21.060.50
- CCS
- 发布
- 2004
- 实施
이 규격은 원통부에 의해 위치 결정하는 지그 및 부착구용의 위치 결정핀(이하 핀이라 한
Locating pins for jigs and fixtures
- ICS
- 21.060.50
- CCS
- J10
- 发布
- 2003-11-05
- 实施
- 2003-11-05
Positioning pins for jigs and attachments
- ICS
- 21.060.50
- CCS
- 发布
- 2003-11-05
- 实施
Positioning pins for jigs and attachments
- ICS
- 21.060.50
- CCS
- 发布
- 2003-11-05
- 实施
A-A-1959, dated 1 July 1994, has been reviewed and determined to be valid for use in acquisition
NAIL (CASING)
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2003-09-08
- 实施
이 규격은 공칭 지름 d가 3∼100 mm 이내에 있는 미터계로, 머리 있는 클레비스
Clevis pins with head
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2003-06-30
- 实施
- 2003-06-30
5.1 Nails are a common mechanical fastener in wood structures. Engineering design procedures used to determine the capacities of laterally-loaded nailed connections currently use a yield theory to establish the nominal resistance for laterally-loaded nailed connections that are engineered. In order to develop the nominal resistance for laterally-loaded nailed connections, the bending yield moment must be known. 1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Test Method for Determining Bending Yield Moment of Nails
- ICS
- 21.060.50
- CCS
- 发布
- 2003
- 实施
