21.060.50 销、钉 标准查询与下载
共找到 563 条与 销、钉 相关的标准，共 38 页
Fasteners — Grooved pins with round head — Full-length diamond grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Grooved pins — One-third-length center grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Parallel grooved pins, with pilot point — Full-length diamond grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Reverse-taper grooved pins — One quarter-length progressive grooves on both sides
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Grooved pins — Half-length center grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Grooved pins with countersunk head — Full-length diamond grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Grooved pins — General requirements
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Taper grooved pins — Half-length progressive grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Taper grooved pins — Full-length progressive grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
Fasteners — Parallel grooved pins — Half-length diamond grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2023-09
- 实施
本文件规定了重型挖掘机用销轴的术语和定义、分类、尺寸和标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于36t及以上重载型挖掘机用销轴（以下简称销轴）。
Structural Pin for heavy-duty excavator
- ICS
- 21.060.50
- CCS
- C348
- 发布
- 2022-08-24
- 实施
- 2022-09-01
本文件规定了重型挖掘机用销轴的术语和定义、分类、尺寸和标记、技术要求、试验方法、检验规则、标志、包装、运输和贮存。
Structural Pin for heavy-duty excavator
- ICS
- 21.060.50
- CCS
- C348
- 发布
- 2022-08-24
- 实施
- 2022-08-30
The terms included in these definitions are listed in alphabetical order under nine headings to facilitate quick reference and in certain cases are sub-categorized. They are intended to apply to metal nails. Omitted are terms relating to tacks, pins, drift pins, dowels, studs, spikes, staples, and other fasteners, such as nail plates. Also omitted are terms relating to the testing and the performance of nails, that is, their drivability, withdrawal resistance, lateral load transmission, creep, protrusion resistance, and splitting; and methods of use, such as face, toe, side, and end-nailing, spacing, loading conditions, etc. These subject matters will be covered in a separate definition of terms relating to mechanical fasteners.
Standard Terminology of Nails for Use with Wood and Wood-Base Materials
- ICS
- 21.060.50
- CCS
- 发布
- 2022-06-01
- 实施
本文件规定了硬质钢钉的术语和定义、标记、要求、试验方法、检验规则、包装、标识、运输及贮存。 本文件适用于制造手动工具捶击用硬质钢钉。
hard steel nail
- ICS
- 21.060.50
- CCS
- C314
- 发布
- 2022-05-10
- 实施
- 2022-05-16
1.1 This test method covers procedures for determining the bending yield moment of nails when subjected to static loading. It is intended only for nails used in engineered connection applications, in which a required connection capacity is specified by the designer. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. NOTE 1—This test method is applicable in either inch-pounds F1575 or SI Units [F1575M]. Values stated in SI are a mathematical conversion of two significant digits and are shown in brackets [ ]. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Method for Determining Bending Yield Moment of Nails
- ICS
- 21.060.50
- CCS
- 发布
- 2021-12-01
- 实施
