21.060.50 销、钉 标准查询与下载
共找到 563 条与 销、钉 相关的标准，共 38 页
Self-tapping screws for wooden structures
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2020-12-29
- 实施
- 2021-06-01
Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins (Inch Series)
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2020-12-21
- 实施
1.1 These test methods cover procedures for the testing of nails. The test or tests selected, and the requirements for compliance, will be as specified in the applicable product standard. Performance tests for nail withdrawal and lateral load capability are not included as they are covered by Test Methods D1761. 1.2 The tests described are as follows: Section Dimensional tests 5 Tension test 6 Conventional bend test 7 Impact bend test 8 Rockwell hardness test 9 Coating weight test 10 Coating adherence test for zinc-coated nails 11 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Test Methods for Nails
- ICS
- 21.060.50
- CCS
- 发布
- 2020-12-15
- 实施
Clevis pins and cotter pins(Inch series)
- ICS
- 21.060.50
- CCS
- 发布
- 20201203
- 实施
- 20201203
Coiled and slotted tubular spring pin
- ICS
- 21.060.50
- CCS
- 发布
- 20201203
- 实施
- 20201203
Dowel pins(parallel pins, hardened)
- ICS
- 21.060.50
- CCS
- 发布
- 20201124
- 实施
- 20201124
Spring-type straight pins — Slotted, heavy duty
- ICS
- 21.060.50
- CCS
- 发布
- 2020-11-24
- 实施
Spring-type straight pins — Slotted, heavy duty
- ICS
- 21.060.50
- CCS
- 发布
- 2020-11-24
- 实施
Spring-type straight pins — Slotted, heavy duty
- ICS
- 21.060.50
- CCS
- 发布
- 2020-11-24
- 实施
Spring-type straight pins — Slotted, light duty
- ICS
- 21.060.50
- CCS
- 发布
- 2020-11-24
- 实施
Spring-type straight pins — Slotted, light duty
- ICS
- 21.060.50
- CCS
- 发布
- 2020-11-24
- 实施
1.1 This specification covers requirements for steel wire nails suitable for use in the application of gypsum board. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test method portion, Sections 7 and 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Nails for the Application of Gypsum Board
- ICS
- 21.060.50
- CCS
- 发布
- 2020
- 实施
