21.060.50 销、钉 标准查询与下载
共找到 563 条与 销、钉 相关的标准，共 38 页
Fasteners — Grooved pins — Half-length center grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Taper grooved pins — Full-length progressive grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Grooved pins — General requirements
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Reverse-taper grooved pins — One quarter-length progressive grooves on both sides
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Parallel grooved pins, with chamfer point — Full-length diamond grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Grooved pins — One-third-length center grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Taper grooved pins — Half-length progressive grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Reverse-taper grooved pins — Half-length progressive grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
Fasteners — Parallel grooved pins — Half-length diamond grooves
- ICS
- 21.060.50
- CCS
- 发布
- 2013-04
- 实施
This Standard specifies slotted spring pins and coiled spring pins (hereafter referred to as "spring pins").
Spring pins
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2013-01-21
- 实施
- 2013-01-21
This International Standard specifies the characteristics of split pins
Split pins
- ICS
- 21.060.50
- CCS
- 发布
- 2012-12-31
- 实施
Grooved pins, half length grooved with gorge
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2012-05-01
- 实施
Taper pins with thread ends and constant taper lengths
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2012-05-01
- 实施
This Standard specifies the characteristics of dowel pins of hardened steel and martensitic stainless steel with nominal diameters d from 1 mm to 20 mm inclusive. NOTE ：The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 8734-1997 Parallel pins,of unhardened steel and martensitic stainless steel (Dowel pins) (MOD) In addition,symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21-1.
Dowel pins (Parallel pins, hardened)
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2012-04-20
- 实施
- 2012-04-20
This Standard specifies the characteristics of parallel pins of steel and austenitic stainless steel with nominal diameters d from 0.6 mm to 50 mm inclusive. NOTE：The International Standard corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 2338-1997 Parallel pins, of unhardened steel and austenitic stainless steel (MOD) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standard and JIS are IDT (identical), MOD (modified), and NEQ (not equivalent) according to ISO/IEC Guide 21-1.
Parallel pins
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2012-04-20
- 实施
- 2012-04-20
This Standard specifies the characteristics of parallel pins with internal thread of unhardened steel and austenitic stainless steel, and those of hardened steel and martensitic stainless steel with nominal diameters d1 from 6 mm to 50 mm inclusive. NOTE ：The International Standards corresponding to this Standard and the symbol of degree of correspondence are as follows. ISO 8733-1997 Parallel pins with internal thread, of unhardened steel and austenitic stainless steel ISO 8735-1997 Parallel pins with internal thread, of hardened steel and martensitic stainless steel (overall evaluation ：MOD) In addition, symbols which denote the degree of correspondence in the contents between the relevant International Standards and JIS are IDT (identical),MOD (modified),and NEQ (not equivalent) according to ISO/IEC Guide 21-1.
Parallel pins with internal thread
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2012-04-20
- 实施
- 2012-04-20
Standard Terminology of Nails for Use with Wood and Wood-Base Materials
- ICS
- 21.060.50
- CCS
- 发布
- 2012-04-01
- 实施
Steel nails for timber structures
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2012-02-23
- 实施
- 2012-07-01
本标准规定了木结构用钢钉的术语和定义、分类、要求、试验方法、检验规则、包装、标记、标识、运输 及贮存。 本标准适用于在制造木结构建筑中使用的钢钉。
Steel nails for timber structures
- ICS
- 21.060.50
- CCS
- J13
- 发布
- 2012-02-23
- 实施
- 2012-07-01
1.1 This specification covers requirements for steel wire nails suitable for use in the application of gypsum board. 1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 The following precautionary caveat pertains only to the test method portion, Sections 7 and 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Nails for the Application of Gypsum Board
- ICS
- 21.060.50
- CCS
- 发布
- 2011-04-12
- 实施
