21.120.10 轴 标准查询与下载

DIN 5480-15 Berichtigung 1:2009 基于参考直径的渐开线花键.第15部分:检查.技术勘误DIN 5480-15-2006

Involute splines based on reference diameters - Part 15: Inspection, Corrigendum to DIN 5480-15:2006-03

DIN 5480-2:2006 基于参考直径的渐开线花键.第2部分:标称和检验尺寸

Involute spline shafts manufactured to this standard are used for clearance, sliding and interference connections of shafts and hubs. They contain all characteristics for the transmission of torque, the location and an economic production.

Involute splines based on reference diameters - Part 2: Nominal and inspection dimensions

DIN 5480-16:2006 基于参考直径的渐开线花键.第16部分:工具

This standard defines the basic design features of hobbing tools (spline hobs, pinion-type cutters), broaches and cold-rolling tools for side-fit involute splines. This standard applies to involute splines based on reference diameters in accordance with DIN 5480-1 and DIN 5480-2.

Involute splines based on reference diameters - Part 16: Tools

DIN 5480-1:2006 基于参考直径的渐开线花键.第1部分:总则

This standard applies to involute splines and spline joints based on reference diameters for connecting hubs and shafts either with a removable connection, a sliding fit or a permanent fit. It lays down the following general characteristics for splines as in this standard: a) They have a standard pressure angle of 30~. b) The basic rack profile is the same for all pitches, therefore applying a uniform design rule to all profiles. c) They have a side fit profile (a diameter fit is permitted in some cases). d) Addendum modification is used in order to achieve specific reference diameters. e) The fit system includes tolerances for effective form deviations so that the effect of such deviations on backlash is taken into account. The specified range of fundamental deviations and tolerance classes takes due consideration of all requirements.

Involute splines based on reference diameters - Part 1: Generalities

DIN 5480-15:2006 基于参考直径的渐开线花键.第15部分:检查

This standard applies to involute splines and spline joints in accordance with DIN 5480-1 and DIN 5480-2. It defines the acceptance testing of such splines and describes the gauges to be used and their verification.

Involute splines based on reference diameters - Part 15: Inspection

AS 1403:2004 旋转钢轴的设计

Design of rotating steel shafts

KS B ISO 496-2003(2008) 远东和驱动的机器 - 轴高

Driving and driven machines－Shaft heights

VDI 2722-2003 万向轴和万向轴系 等运动机构

The document will be concerned solely with cardan shafts and cardan shaft lines which contain universal joints. Cardan shafts consist of a drive shaft, a universal joint and an output shaft. Cardan shaft lines have more than two universal joints. The aim of this guideline is to outline from the kinematic point of view the possibilities for connecting universal-joint mechanisms in series and to describe the conitions for a homokinematic transmission of movement between the driving and driven shafts of cardan shafts and cardan shaft lines.

Cardan shafts and cardan shaft lines - Homokinematic mechanisms

JIS B 0904:2001 1:10锥度比的圆锥形轴端

この規格は，一般に用いる伝動用回転軸の軸端のうち，はめあい部のテーパ比が1: 10の円すい形体(以下，軸端という。)で，軸端に基木直径が6-630 mmのものの主要寸法について規定する。

Conical shaft ends for cone taper ratio 1:10

JIS B 0903:2001 圆柱形轴端

この規格，一般に用いられる伝動用回転軸の軸端のうち，はめあいを適用する部分が円筒形のもの(以下，軸端という。)で，その直径ガ6-630 mmの主要寸法について規定する。

Cylindrical shaft ends

JIS B 0902:2001 驱动机械和从动机械.旋转轴高度

この規格は，駆動機及び被駆動機に対する軸高さめ四つの寸法系列について規定する。備考 この規格の対応国際規格を，次に示す。なお，対応の程度を表す記号は，ISO/IEC Guide 21に基づき， IDT(一致している)，MOD（修正している），NEQ(同等でない)とする。

Driving and driven machines -- Shaft heights

KS B 6874-2000(2010) PANTONG圆锥用于凹版印刷机的连接

Taper cone for connecting printing cylinder of gravure printing press

DIN 743 Bb.1:2000 轴类.负载能力的计算.样品

Shafts and axles, calculation of load capacity - Examples

DIN 5466-1:2000 花键接头,载荷能力计算.第1部分:一般基础

Splined joints, calculation of load capacity - Part 1: General basis

DIN 743-3:2000 轴类.负载能力的计算.第3部分:材料强度

The document gives indications for necessary material strength for the fatigue strength according to DIN 743-1.

Shafts and axles, calculation of load capacity - Part 3: Strength of materials

DIN 743-2:2000 轴类.负载能力的计算.第2部分:理论应力集中因素和疲劳缺口因素

The document indicates the necessary influence factors for the calculation of the component fatique strength according to DIN 743-1.

Shafts and axles, calculation of load capacity - Part 2: Theoretical stress concentration factors and fatigue notch factors

DIN 743-1:2000 轴类.负载能力的计算.第1部分:一般基础

The aim of the document is to lay down the basis for caluclation of shafts and axles for the general mechanical engineering.

Shafts and axles, calculation of load capacity - Part 1: General basics

DIN 3760:1996 旋转轴唇形密封环

This document specifies rotary shaft lip type seals for the sealing of rotating shafts in operating conditions without pressure difference or low pressure difference.

Rotary shaft lip type seals

ANSI B92.1, 1A-1996 渐开线花键及检验标准

Involute Splines and Inspection Standard

DS 813:1996 干涉接头 计算和设计规则

This standard establishes the basis of calculation for interference joints with cylindrical surfaces of contact, parts of which are of metallic materials. This standard applies to the field of machine design. The content of definitions may also apply to other fields e.g. precision mechanics. The purpose of this standard is to increase the liability in interference joint and to reduce the cost of manufacture.

Interference joints - Calculation and design rules