21.120.10 轴 标准查询与下载

JIS B 0903:1977 圆柱形轴端

Cylindrical shaft ends

JIS B 0901:1977 轴径

この規格は，一般に用いられる円筒軸のはめあい部分の直径のうち，4mm以上630 mm以下のもの(以下，軸径という。)について規定する。

Diameter of shafts

DIN 41591:1976 机电元件用轴端

Spindle ends for electromechanical componentsZusammenhang mit der von der International Electrotechnical Commission (IEC) herausgegebenen, Publikation IEC 390 sowie einer in Vorbereitung befindlichen Erg?nzung siehe Erl?uterungen.

Spindle ends for electromechanical components

DIN 75532-1:1976 旋转运动的传动装置.第1部分:连接齿轮、中间齿轮、挠性驱动轴与装置的连接方式

Transmission of rotary motions; joinings types on gears, intermediate gears, driving shafts and implementsInhalt dieser Norm sind neben den Festlegungen der Formen von Anschlüssen an Getrieben, Zwischengetrieben, biegsamen Wellen und Ger?ten die vorwiege

Transmission of rotary motions; Types of connection to gears, intermediate gears, flexible drive shafts and equipment

JIS B 0902:1976 发动和从动机旋转轴高度

Shaft heights for driving and driven machines

SAE J499A-1975 配件中软开启孔的平行侧花键

This Information Report along with SAE J500 and J501 is generally understood to be technically obsolete for the design of new applications. however, it is listed for those existing applications where it may be required. For the design of new applications, consult ANSI b92.1-1970-- involute Splines and Inspections Standard.

Parallel Side Splines for Soft Broached Holes in Fittings

DIN 5471:1974 机床.带4个键的花键轴和花键孔的剖面.内定心.尺寸

Machine tools; splined shaft and splined bore profiles with 4 splines; internal centering; dimensionsMachines-outils; arbres cannelés et moyeux cannelés, profiles avec 4 clavettes; centrage intérieur; dimensions

Machine Tools; Spline Shafts and Spline Bore Profiles with 4 Splines, Internal Centering, Dimensions

CSN 01 4992-1974 带锥度1的圆锥轴端1：10．基本尺寸

Zpracovatel: P?erovské strojírny, n. p., P?erov - B?etislav Kratochvíl Pracovník ??adu pro normalizaci a mě?ení: Ing. Zdeněk Jícha

Conical shaft ends with the conity 1:10. Basic dimensions

BS 4823:1972 圆柱轴端配件孔径的选择指南

Guidance is given on the selection of suitable tolerances (extracted from BS 4500) for the bore diameters of shaft fitments (e.g. couplings, pulleys) to give interference, close and free fits when the fitments are used with cylindrical shaft ends to BS 4506.

Guide to the selection of fitment bores for cylindrical shaft ends

GOST 12081-1972 1:10的锥形轴端.基本尺寸.允许的扭矩

Настоящий стандарт распространяется на конические концы валов с конусностью 1:10, диаметром от 3 до 630 мм, предназначенные для посадки детал

1:10 Conical shaft ends. Basis dimensions. Permissible torquie

NF E22-050:1970 圆柱的和1/10锥度的锥形轴端.总则

Cylindrical and 1/10 conical shaft ends.general.

NF E22-051:1970 圆柱形轴端.长系列(标准的)

Cylindrical shaft ends.long series (normal).

NF E22-052:1970 圆柱形轴端.短系列

Cylindrical shaft ends.short series.

NF E22-053:1970 圆柱形轴端.长和短系列.可传送的扭矩

Cylindrical shaft ends.long and short series.transmissible torques.

BS 4506:1970 轴端规范

Specifies shapes and sizes of cylindrical and conical shaft ends with keyways in diameters 6 mm to 630 mm inclusive. Provision is made for both long and short series and for external and internal screw threads for retaining matching parts by means of nut or screw.

Specification for shaft ends

DIN 1448-1:1970 带外螺纹的锥形轴端.第1部分:尺寸

Conical shaft ends with external thread, dimensionsZusammenhang mit der ISO-Empfehlung ISO/R 775-1969 siehe Erl?uterungen.Die kegeligen Wellenenden sind bestimmt für die Aufnahme von Riemenscheiben, Kupplungen und Zahnr?dern.Nicht angegebene Ma?e und E

Conical Shaft Ends with External Thread; Dimensions

DIN 748-1:1970 圆柱形轴端.第1部分:尺寸、公称传动力矩

Cylindrical Shaft Ends; Dimensions, Nominal Transmissible Torques

NF E22-151:1967 直齿花键.圆柱轴和轴套

CYLINDRICAL STRAIGHT-SIDED SERRATIONS.

GOST 12080-1966 轴的圆柱端

Настоящий стандарт распространяется на цилиндрические концы валов диаметром от 0,8 до 630 мм, предназначенные для посадки деталей, передающ

Cylindrical ends of the shafts

DIN 5464:1965 直边式花键.重型系列

Straight-sided splines; heavy series

Straight-sided Splines; Heavy Series